• Journal of the Korea Organic Resources Recycling Association
• /
• v.19 no.1
• /
• pp.109-114
• /
• 2011

This study was conducted to investigate the effect of hydraulic retention time(HRT) on the power density in a horizontal flow microbial fuel cell(MFC) reactor. When HRTs were 15min, 30min, 60min and 180min, maximum power densities were $24.7mW/m^2$, $27.3mW/m^2$, $22.8mW/m^2$ and $17.2mW/m^2$, respectively. The highest power density was obtained at HRT of 30min. It was 59% improvement when compared to the power density at an HRT of 180min. When HRT was increased, COD removal rate increased whereas the coulombic efficiency remained constant. The result shows that the optimal performance of the horizontal flow MFC reactor could be achieved at HRT of 30min.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.21 no.1
• /
• pp.39-44
• /
• 2013

This study evaluated the effect of fluid flow on the power density in a horizontal-flow microbial fuel cell (MFC). The maximum power densities in four types of flow induced by different channel types in the anode chamber were investigated. The fluid flow at each channel was analyzed using tracer tests. Results of polarization curves showed that the maximum power densities of case 1, 2, 3 and 4 were 95.7, 129.1, 190.9 and 114.2 mW/m2, respectively. Case 3 with a set of guide walls where flow had an S type-like shape showed the highest power density. Based on the Morrill Dispersion Index (MDI) value of case 4, microbial activity would be enhanced since the reactor allows even distribution of substrate but the overflow occurrence would not guarantee stable performance. Therefore, case 3 could be an effective reactor type for MFC because of high electricity generation and stable performance.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.16 no.2
• /
• pp.87-92
• /
• 1987

Crease cut pearled baller was studied in relation to product and quality, and processing electricity requirement with various pearling yields. 1. Increasing the pearling rate resulted in increasing broken grain of cut-Polished barley. 2. The range of length/width ratio in cut-polished baller were from 2.09 to 2.13 and those of pearled barley were 1.36, respectively. 3. Cut-polished barley required more electricity than pearled barley at the same polishing rate. As pearling rate increased at first polishing before cutting, total electricity requirement of cut-polished barley reduced significantly.

• Journal of Advanced Navigation Technology
• /
• v.15 no.4
• /
• pp.562-570
• /
• 2011

In this paper, a distributed mobile relay power control (DMRPC) scheme for maximizing individual cell throughput is proposed for mobile relay aided multi-cell orthogonal frequency division multiplexing (OFDM)-time division duplex (TDD) system. In the system with DMRPC, the power levels of relay's are controlled by individual cell without cell cooperation and signalling overhead. It is demonstrated by numerical simulation that DMRPC provides the better cell throughput performance than either the full power relay aided system or conventional system without relay does. Moreover, it is also shown that relay aided systems with DMRPC, and the conventional system have almost identical cell edge throughput, while full power relay aided systems show worse performance in cell edge throughput.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.11 s.353
• /
• pp.85-94
• /
• 2006

Simple-relay aided resource allocation (SRARA) schemes are incorporated with throughput guarantee scheduling (TGS) in IEEE 802.16 type TDD-OFDMA downlink to enhance service coverage, where the amount of resources at each relay is limited due to either its available power which is much smaller than base station (BS) power or the required overhead The performance of SRARA schemes is evaluated with both proportional fair (PF) and TGS schedulers at 64 kbps and 128 kbps user throughput requirements. For SRARA with RSs of relatively lower power, a scheme putting total power into only one subchannel shows larger coverage than when both subchnnels are used in a manner of equal power allocation, while the RS with evenly power-allocated two subchannels could provide larger coverage gain for a relatively higher power. In a lower target (64kbps), more improvement comes from relay scheme rather than scheduler design. For a relatively higher level (128 kbps), it comes from scheduler design rather than relay.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.122-129
• /
• 2014

Due to remarkable market growth of smart devices, higher performance and more functionalities are required for a core system-on-chip (SoC), and thus the power demand is rapidly increasing. However, aggressive shrink of CMOS transistor have brought severe process variations thereby adversely affected the performance and power consumption under strict power constraint. Voltage binning (VB) scheme is one of the effective post silicon tuning techniques, which can reduce parametric yield loss due to process variations by adjusting supply voltage. In this paper, an optimal supply voltage tuning based voltage binning technique is proposed to reduce average power without an additional yield loss. Considering the different LVCC margins of process corners along with speed and leakage characteristics, the proposed method can optimize the deviation of voltage margin and thus save power consumption. When applying on a 30nm mobile SoC product, the experimental results showed that the proposed technique reduced average power consumption up to 6.8% compared to traditional voltage binning under the same conditions.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.251-251
• /
• 2012

다양한 금속기판 위에 탄소나노튜브(CNT)를 직접성장 시키는 경우, 플라즈마를 이용한 기판 전처리가 CNT의 저온 합성 및 합성수율 향상에 미치는 영향을 살펴보았다. 합성용 금속기판으로는 SUS316L, Inconel, Invar, Hastelloy 등 Ni계 합금을 이용하였다. 전처리 시 플라즈마의 인가전력 및 기판온도의 증가에 따라 기판 표면조도의 증가를 확인하였고, 그에 따른 합성온도 저하 및 합성수율 증대 결과를 얻었다. 기판 열처리를 부가적으로 실시한 경우, 기판 열처리 온도 또한 합성수율에 영향을 미침을 알 수 있었으며, 특히, 인코넬 기판의 경우, 열처리 후 플라즈마 전처리를 실시한 기판에서 합성수율이 크게 향상되는 것을 알 수 있었다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.1A
• /
• pp.9-12
• /
• 2007

In this paper, we propose and analyze a scheme for wireless channels, which is a combination of a type I hybrid-automatic repeat request (H-ARQ) scheme and a power ramping. The power ramping is considered for more reliable downlink data transmission, in which the transmission power is gradually changed from a small level to a large level when the number of retransmissions increases. The simulation results demonstrate that, when the power ramping step size is 0.5dB, the average throughput gain may be as high as 2% to 5% with properly selected parameters.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.604-607
• /
• 2001

본 논문은 새로운 타입의 중첩형 오존발생기를 제안하였다. 방전시 방전실 내의 과도한 방전전력은 온도상승을 가져온다. 이러한 열로 인해 오존분해반응이 생성되어 오존생성수율이 나빠진다. 제안한 전원장치는 잉여전력을 재충전하여 열의 발생을 억제하고 오존분해반응을 줄일 수 있음을 실험으로 검증하였다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.5A
• /
• pp.387-393
• /
• 2007

In this paper, we propose the load control procedure for WiBro system in order to keep the data traffic throughput maximum. The transmitter at a mobile terminal can estimate maximum available power for each user and then the maximum number of subchannels can be calculated considering the total available power. The data traffic throughput and the total throughput (the sum of signaling traffic and data traffic throughput) are considered. As the number of bandwidth requests per frame increases, the data traffic throughput can significantly decrease. Therefore, the load control procedure is indispensible to maintain the data throughput at the maximum level. So, we propose the load control procedure to prevent data traffic throughput from decreasing and evaluate the proposed procedure through the computer simulation under the multi-user environment. The maximum throughput can be maintained by applying the proposed procedure.