• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.47-54
• /
• 2006

This work proposes a dual-channel 6b 1GS/s ADC for ultra wide-band communication system applications. The proposed ADC based on a 6b interpolated flash architecture employs wide-band open-loop track-and-hold amplifiers, comparators with a wide-range differential difference pre-amplifier, latches with reduced kickback noise, on-chip CMOS references, and digital bubble-code correction circuits to optimize power, chip area, and accuracy at 1GS/s. The ADC implemented in a 0.18um 1P6M CMOS technology shows a signal-to-noise-and-distortion ratio of 30dB and a spurious-free dynamic range of 39dB at 1GS/s. The measured differential and integral non-linearities of the prototype ADC are within 1.0LSB and 1.3LSB, respectively. The dual-channel ADC has an active area of $4.0mm^2$ and consumes 594mW at 1GS/s and 1.8V.

• Journal of Advanced Navigation Technology
• /
• v.21 no.4
• /
• pp.377-385
• /
• 2017

The solar cell need the characteristic interpreting because the solar cell changes greatly according to the isolation, temperature and load in the photovoltaic development. Moreover, to get many energy in photovoltaic development need the position tracking of the sun according to the environment change. Also, The solar cells should be operated at the maximum power point. In this paper, I used microprocessor and sensor and designed to improve the efficiency of the photovoltaic system the photovoltaic position tracker device, and compared the normal photovoltaic system of fixed form with the photovoltaic system of solar position tracked form. Moreover, compared the catalogue of solar cell module and the simulation through a mathematics modelling with the solar cell's characteristic interpreting and composed an power conversion system with boost converter and voltage source inverter. Used the constant voltage control method for maximum power point tracking in boost converter control and, used the SPWM(Sinusoidal Pulse Width Modulation) control method in inverter control. The result was less then 5% when compared the catalogue of solar cell module and the simulation through a mathematics modelling. The boost rate of boost converter was similar to 167 % with the simulation.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.3
• /
• pp.96-101
• /
• 2015

This paper describes a design and implementation of the NFC bridge chip which performs interface between kinds of devices and mobile phones including NFC controller through NFC communication. The NFC bridge chip consists of the digital part and the analog part which are based on NFC Forum standard. Therefore the chip treats RF signals and then transforms the signal to digital data, so it can interface kinds of devices with the digital data. Especially the chip is able to detect RF signals and then wake up the host processor of a device. The wakeup function dramatically decreases the power consumption of the device. The carrier frequency is 13.56MHz, and the data rate is up to 424kbps. The chip has been fabricated with SMIC 180nm mixed-mode technology. Additionally an NFC bridge chip application to the blood glucose measurement system is described for an application example.

• Journal of the Korea Computer Industry Society
• /
• v.8 no.2
• /
• pp.107-112
• /
• 2007

Laser wave length can have evaporation effect by absorption because outer skin or tissue of focus is consisted of water almost though absorption of water occurs more than 90% almost in formation thickness of very thin floor. Can operate outer skin, steam by floor and correct incision of formation is available. Suture surgical operation is available to vein or lymph system and surgical operation region can dry and see as eye and radish bleeding surgical operation is available. Specially, stability of tube both end output about pulse by weight very, this research can cause various curative effect because can reduce bulk and control easily current wave style of medical laser using electric power conversion device of high frequency way. If introduce ZVS (Zero Voltage Switching) or ZVZCS (Zero Voltage and Zero Current Switching), is more profitable because can reduce switching damage. Because electric power department of proposed medical laser can do stable soft-switching in wide subordinate extent introducing ZVZCS technique by the first help and control department composes microcontroller, output current waveform user have free form make Result that experiment because design and manufacture, brought result that improve of 20% than existing equipment, and will be bought to get into superior result if supplement as systematic late.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.2
• /
• pp.379-385
• /
• 2017

In general, distribution board, panel board and motor control center can be installed over a wide area such as residence of group, building, schools, factories, ports, airports, water service and sewerage, substation and heavy industries that are used to supply converts the voltages extra high voltage into optimal voltage. There are electrical accidents due to rise of contact temperature, loose contact between busbar, deterioration of the contact resistance, over temperature of the busbars. In this paper, we designed and implemented the busbar joint and temperature measurement system, which can measure the joint resistance of busbar and loose connection between busbar using potentiometer and non-contact infrared sensor. The experimental results show that tightening the bolt and nut is fully engaged, resistance was decreased and maximum error range was 0.1mm. Also, the experimental result showed that the temperature at the contact area is increased from $27.3^{\circ}C$ to $69.3^{\circ}C$by the contact resistance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.745-752
• /
• 2016

In the era of the Internet of Things, where all physical objects are connected to the Internet, we suggest a remote control system using a Raspberry Pi single-board computer with ZigBee, which can turn an indoor light-emitting diode (LED) and a multiple-tap on and off, and with a smart phone can control the brightness of the LED as well as an electronic door lock. By connecting an infrared (IR) transmitter module to the Raspberry Pi, we can control home appliances, such as an air conditioner, and we can also monitor indoor images, indoor temperatures, and illumination by using a smart phone app. We developed a method of finding out IR transmission codes required for remote-controllable appliances with an AVR micro-controller. We suggest a method to remotely open and shut an office door by novating the door lock. The brightness level of an LED (between 0 and 10) can be controlled through a PWM signal generated by an ATmega88 microcontroller. A mutiple-tap is controlled using an ATmega32, a photo-coupler, and a TRIAC. The signals for measured temperature and illumination are converted from analog to digital by using the ATtiny44A microcontroller transmitting to a Raspberry Pi through SPI communication. Then, we connect a camera to the CSI head of the Raspberry Pi. We can turn on the smart multiple-tap for a certain period of time, or we can schedule the multi-tap to turn on at a specific time. To reduce standby power, people usually pull out a power code from multiple-taps or turn off a switch. Our method helps people do the same thing with a smart phone, if they are away from home.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.2
• /
• pp.120-128
• /
• 2016

This paper describes power generation from sea waves by using linear permanent magnet generator. A buoy is placed on the ocean surface and connected to the generator. The wave energy is carried out from the movement of a buoy. An electrical conversion system is needed between the generator and the grid. For an analysis of the power system, the modeling of the linear generator and converter system was proceeded. This paper proposes vector control method for wave power generation system using linear generator. In order to verify the proposed method, simulation and experiment performed and the results support the validity of the control scheme.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.4
• /
• pp.456-465
• /
• 2019

PHEV(Plug in Hybrid Electric Vehicle) and BEV(Battery Electric Vehicle) equip high voltage batteries to drive motor and vehicle electric system. Those vehicle require OBC(On-Board Charger) for charging batteries and LDC(Low DC/DC Converter) for converting from high voltage to low voltage. Since the charger and the converter actually separate each other in electrical vehicles, there is a margin to reduce the vehicle weight and area of installation by integration two systems. This paper studies a 1.5kW LDC converter that can be integrated into an OBC using an isolated current-fed converter by simplifying the design of LDC transformers. The proposed LDC can control the final output voltage of the LDC by using a fixed arbitrary output voltage of the bidirectional buck-boost converter, so that Compared to the existing OBC-LDC integrated system, it has the advantage of simplifying the transformer design considering the battery voltage range, converter duty ratio and OBC output turn ratio. Prototype of the proposed LDC was made to confirm normal operation at 200V ~ 400V input voltage and maximum efficiency of 91.885% was achieved at rated load condition. In addition, the OBC-LDC integrated system achieved a volume of about 6.51L and reduced the space by 15.6% compared to the existing independent system.

• Journal of Broadcast Engineering
• /
• v.19 no.4
• /
• pp.491-501
• /
• 2014

Recently, the need for disaster-preventing broadcast has increased gradually to cope with natural disaster like earthquake and tsunami causing enormous losses of both life and property. In disaster-preventing broadcast system, the wake-up signal is used to alert user terminal and switch the current state of channel to the emergency channel, which is for the fast and efficient delivery of emergency information. In this paper, we propose the detection method of wake-up signal for disaster-preventing broadcast systems. The wake-up signals for disaster-preventing broadcast should have a good auto-correlation property in low power and narrow-band conditions that does not affect the existing digital television (DTV) system. The suitability of the m-sequence and complementary code (CC) is analyzed for wake-up signals according to signal to noise ratio. A wake-up signal is proposed by combining the direct sequence spread spectrum (DSSS) technique and pseudo noise (PN) sequences such as Barker and Walsh-Hadamard codes. By using the proposed method, a higher detecting performance can be achieved by the spreading gain compared to the single long m-sequence and the Golay code.

• Proceedings of the Korean Information Science Society Conference
• /
• 2001.04a
• /
• pp.37-39
• /
• 2001

반도체 설계는 급속한 기능 추가와 기가 헬쯔에 육박하는 고속 동작에 부응하는 제품의 설계와 빠른 출시를 위하여 다방면의 연구를 거듭하고 있다. 하지만, 인터넷과 정보 가전의 모바일 기기에서 요구하는 폭발적인 기능의 추가와 가전기기의 최소화를 위하여서는 그 요구를 감당하지 못하고 있다. 이를 위한 방안으로 설계 재활용과 System-On-Chip의 설계가 수년 전부터 대두되었으나 아직 큰 실효를 거두지 못하고 있다. SoC설계는 다기능을 한 칩에 구성하는 방법을 시도하고 있고, 설계 재활용은 기존의 설계(IP)를 다른 것과 혼합하여 필요한 기능을 제공하는 방법이 시도되고 있다. 이 두가지의 VLSI 설계 방식 흐름을 가능하도록 하기 위한 연구로써, 레이아웃 이식에 관한 연구를 진행하였다. IP 재활용을 위하여서는 다양한 공정변화에 신속히 대응하고, 기존의 설계 설계규칙으로 설계된 면을 현재의 공정인 0.25um, 0.18um 테크놀러지에 맞도록 변환하는 VLSI 소프트웨어 시스템을 필요로 한다. 레이아웃 설계도면을 분석하여 소자 및 배선을 인식하는 알고리즘을 연구와 개발하고, 도면을 첨단 테크놀러지의 설계 규칙에 부응하도록 타이밍, 소비 전력, 수율을 고려한 최적의 소자 및 배선의 크기를 조절하는 방법을 고안하며, 칩 면적을 최적화할 수 있는 컴팩션 알고리즘을 개발하여 레이아웃 설계 도면을 이식할 수 있는 자동화 소프트웨어 시스템을 연구하였다. 더불어, 현재 반도체 소프트웨어 시스템의 최대 문제점에 해당하는 처리 속도와 도면의 처리 능력을 비교, 검토하여 본 연구가 속도면에서 평균 27배 효율면에서 3배 이상의 상대우위를 점하였다.전송과 복원이 이루어질 것이다.하지 않은 경우 단어 인식률이 43.21%인 반면 표제어간 음운변화 현상을 반영한 1-Best 사전의 경우 48.99%, Multi 사전의 경우 50.19%로 인식률이 5~6%정도 향상되었음을 볼 수 있었고, 수작업에 의한 표준발음사전의 단어 인식률 45.90% 보다도 약 3~4% 좋은 성능을 보였다.으로서 hemicellulose구조가 polyuronic acid의 형태인 것으로 사료된다. 추출획분의 구성단당은 여러 곡물연구의 보고와 유사하게 glucose, arabinose, xylose 함량이 대체로 높게 나타났다. 점미가 수가용성분에서 goucose대비 용출함량이 고르게 나타나는 경향을 보였고 흑미는 알칼리가용분에서 glucose가 상당량(0.68%) 포함되고 있음을 보여주었고 arabinose(0.68%), xylose(0.05%)도 다른 종류에 비해서 다량 함유한 것으로 나타났다. 흑미는 총식이섬유 함량이 높고 pectic substances, hemicellulose, uronic acid 함량이 높아서 콜레스테롤 저하 등의 효과가 기대되며 고섬유식품으로서 조리 특성 연구가 필요한 것으로 사료된다.리하였다. 얻어진 소견(所見)은 다음과 같았다. 1. 모년령(母年齡), 임신회수(姙娠回數), 임신기간(姙娠其間), 출산시체중등(出産時體重等)의 제요인(諸要因)은 주산기사망(周産基死亡)에 대(對)하여 통계적(統計的)으로 유의(有意)한 영향을 미치고 있어 $25{\sim}29$세(歲)의 연령군에서, 2번째 임신과 2번째의 출산에서 그리고 만삭의 임신 기간에, 출산시체중(出産時體重) $