• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.6
• /
• pp.22-27
• /
• 2012

Drilling process is usually the most efficient and economical method of making a hole in a solid body. However, there have been no analytical method to assess drilling process based on the shear and frictional characteristics. In this paper, procedures for analyzing shear and frictional processes of drilling have been established by adopting an equivalent turning system to drilling. A series of drilling experiments were carried out with varying feed, velocity and drill shape factors. Using the results of the experiments, the cutting characteristics including shear in the primary shear zone and friction in the chip-tool contact region of drilling process have been analyzed. The specific cutting energy tends to decrease exponentially with increase of feed rate. In drilling process 35-40% of the total energy is consumed in the friction process. This is greater than that of turning process in cutting of the same work material.

• Journal of the Korean Geotechnical Society
• /
• v.40 no.3
• /
• pp.41-54
• /
• 2024

Regular monitoring plays a crucial role in ensuring the safety of geotechnical structures. Currently, nondestructive methods are employed to monitor such structures to minimize the impact, e.g., sensor-based accelerometers, displacement meters, image-based lasers, and drone imaging. These technologies can observe surface changes; however, they frequently suffer difficulties in terms of identifying changes in internal properties. To monitor changes in internal properties, in situ geotechnical investigations can be employed. A nondestructive test that can be used for this purpose is the spectral analysis of surface wave (SASW) test using geophones. The SASW test is a nondestructive method; however, due to the time required for data interpretation and the difficulty in analyzing the data, it is challenging to use the SASW test for monitoring applications that require frequent observations. However, it is possible to apply the first-step analysis, which yields the dispersion curve, for monitoring rather than the complete SASW analysis, which yields the shear wave velocity. Thus, this paper presents a fundamental study on the phase difference that derives the dispersion curve to utilize the SASW test for monitoring. The reliability of each phase difference interval is examined to determine the boundary to the subjected monitor. The study used phase difference data obtained using a geophone from a single-layered, homogeneous ground site to evaluate reliable boundaries. The findings of this study are expected to improve the utility of monitoring by identifying the ideal boundary for phase difference data.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.10
• /
• pp.111-122
• /
• 2009

Dissolution of some of geo-materials may yield the loss of the soil strength and the settlement of earth structures. The goal of this study is to monitor the several physical behaviors of soluble mixtures during dissolution. Sand-salt mixtures are used to monitor the meso to macro response including the settlements and shear waves. The mixtures of photoelastic and ice disks are used to monitor micro to meso behavior of soluble mixture including the void ratio, force chain, coordination number and horizontal force changes. In the sand-salt mixtures, shear waves are measured by using bender elements in conventional oedometer cells. In the photoelastic disk - ice disk mixtures, micro to meso response are measured by digital images and load cells. The shear wave velocity decreases at the initial stage of the dissolution, and then increases and approaches to asymptotic value. The larger dissoluble particle and the more random packing produces the severe horizontal fore change. After dissolution, the void increases and the coordination number decreases. This study demonstrates that the particle level behavior such as the changes of the force chain, void ratio, and coordination number affects the global behavior such as the change of the shear wave velocity and horizontal force of the system.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.4 s.71
• /
• pp.493-500
• /
• 2004

In this study, the effects of ring stiffeners for buckling of cylindrical shells with composite materials were analyzed. The finite element method was used: 3-D beam elements were used for stiffeners and flat shell elements were used for cylindrical shells and were improved by introducing a substitute shear strain. The ring stiffeners were of the transverse rib type. The buckling behaviors of the cylindrical shells were analyzed based on various parameters, such as locations and sizes of stiffeners, diameter/length ratios and boundary conditions of shells, and fiber-reinforced angles. Effective reinforcement was examined by understanding the exact behaviors for buckling. The results of the analysis may serve as references for designs and future investigations.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.11
• /
• pp.5-15
• /
• 2014

It is very important to design and construct slopes safely because damage cases are increasing due to slope failure. Recently, Limit Equilibrium Method (LEM) based programs are commonly used for slope designs. Though LEM can give factors of safety through simple calculation, it has a disadvantage that the sliding surface should be assumed in advance. On the other hand, the use of Finite Difference Method (FDM) is increasing since the factor of safety can be easily estimated by using shear strength reduction technique. Therefore the purpose of this study is to present a reasonable slope design methodology by comparing the two commonly used analysis approaches; LEM and FDM. To this end, the reinforcement effects of the two methods were compared in terms of the support pattern of soil nailing reinforced in the section where plane failure is anticipated. As a result, the reinforcement effects by nail angle and nail spacing turned out to be equal. Also it was found that the factor of safety increased in LEM, but not changed in FDM when the nail length increased.

• Journal of the Korean Geosynthetics Society
• /
• v.23 no.2
• /
• pp.19-27
• /
• 2024

Geotechnical structures such as dams, tunnels, and slopes require regular inspection and monitoring to ensure stability. Domestically, drones and accelerometers have become common tools for inspecting and monitoring various structures. However, drones have difficulty identifying internal changes in structures and the subsurface, and accelerometers generally serve for seismic design or strain measurement purposes. Therefore, this paper proposes to utilize accelerometers to monitor the internal information of the ground on a real-time or periodic basis. The proposed method utilizes a part of the analysis technique from the SASW test to monitor the stability and state changes of geotechnical structures. Cases where SASW was used to evaluate the safety of geotechnical structures, such as slopes, dams, and tunnels, were reviewed to verify the suitability of the technology. To make the proposed method more practical, the study considered using only the first-step analysis to derive the dispersion curve rather than the second-step analysis to determine the shear wave velocity profile, which requires complex analysis. The proposed technique is expected to enable the continuous monitoring and inspection of geotechnical structures by utilizing accelerometers.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.281-288
• /
• 2000

In this study, we tried to determine failure criteria for joints of soft rock using ring shear test machine. The residual stress fellowing shear behavior was determined by the result of ring shear test and direct shear test. Ring shear test with the specimens which cover a large deformation range was adapted to measure a residual stress, and was possible to present the peak stress to present the peak stress to the residual stress at the same time. Residual stress is defined a minimal stress of specimens with a large displacement and the result of the peak residual stress is shown by a size of displacement volume. Therefore, the residual stress in soil was decided by shear stress of maximum shear stress - shear displacement(angle) based on the test result of a hyperbolic function ((equation omitted), a, b ＝ experimental constant). In this study, it was proved that the residual stress of rock joint can be determined by using of this method.

• Korean Journal of Materials Research
• /
• v.6 no.5
• /
• pp.532-539
• /
• 1996

동과 동을 저온에서 단시간내에 접합시키는 가능성을 검토하기 위해서 직류 자기 스퍼터링을 이용한 코팅한 주석 및 주석-잡 합금층을 중간층으로 사용하였다. 접합은 대기중 200-35$0^{\circ}C$의 온도에서 수행되었고 접합온도에 도달직후 바로 냉각하였다. 접합 계면에는 액상의 주석과 고상의 동간의 반응에 의해 n-상(Cu6Sn5) 및 $\varepsilon$-상(Cu3Sn)으로 구성된 금속간화함물 층이 형성되었다. 전단강도로 측정된 접합강도는 접합온도에 따라 비례적으로 증가하지만 30$0^{\circ}C$ 이상에서 감소하였다. 접합강도는 2.8-6.2MPa 범위로 나타났으며, 중간층합금 성분에 따른 접합계면에서의 금속간화합물의 생성거동과 관련지어 설명되었다. 실험결과 실용적인 접합법으로서 저온 단시간 접합의 가능성이 확인되었다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.135-138
• /
• 2005

Since a ductile coupled shear wall system is the primary seismic load resisting systems of many structures, a coupling beams of these system must exhibit excellent ductility and energy absorption capacity. In this paper, the seismic response of coupled shear wall system is discussed. It includes that the evaluation of the degree of coupling between the shear walls and the coupling beams. It is demonstrated through a review of experimental investigations of coupling beam behavior that often the coupling beam ductility demand exceeds the expected available ductility. As a result, it is possible that coupled shear wall system will not behave as desired in the course of a significant seismic event. Limits to the allowable degree of coupling are proposed as a remedy to this apparent deficiency.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.257-260
• /
• 2006

Coupled shear walls consist of two or more in-plane walls inter-connected with coupling beams. In order to effectively resist seismic loads, coupling beams must be sufficiently stiff, strong and posses a stable load-deflection hysteretic response. Much of requirements to the civil and building structures have recently been changed in accordance with the social and economic progress. Ductility of high performance fiber reinforced cementitious composites(HPFRCCs), which exhibit strain hardening and multiple crackling characteristics under the uniaxial tensile stress is drastically improved. This paper provides background for design guidelines that include a design model to calculate the shear strength of pseudo strain hardening cementitious composite steel coupling beam.