• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.414-416
• /
• 2003

As environmental conditions for memory products are increasingly high speed/high density, adopting diverse system configuration, it's more and more difficult for current component tester to adopt the actual condition of field application. If system test screening is realized in component level, test coverage failure can be made more secured in the initial stage, evaluation cost can be reduced and the effectiveness of investment for the facility can be maximized. Based on the above background, component automatic system tester was developed and showed off satisfactory results per each memory device family. In this paper, component quality stabilization strategy and cost saving for tester investment through future Quality monitoring and application to mass production will be presented.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.11
• /
• pp.544-547
• /
• 2006

In this paper, we present a temperature-controlled system for MEMS electrical resistance heaters without a temperature sensor. To rapidly control the heater temperature, the microheater system developed consists of a power supply, power amplifier, digital ${\underline{P}}roportional-{\underline{I}}ntegral-{\underline{D}}ifferential$ (PID) controller, and a quarter bridge circuit with the microheater and three resistors are nominally balanced. The microheaters are calibrated inside a convection oven to obtain the temperature coefficient with a linear or quadratic fit. A voltage amplifier applies the supply voltage proportional to the control signal from the PID controller. Small changes in heater resistance generate a finite voltage across the quarter bridge circuit, which is fed back to the PID controller to compare with the set-point and to generate the control signal. Two MEMS microheaters are used for evaluating the developed control system - a NiCr serpentine microheater for a preconcentrator and a Nickel microheater for ${\underline{P}}olymerase\;{\underline{C}}hain\;{\underline{R}}eaction$ (PCR) chip.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.242-244
• /
• 2019

본 논문은 방사선 치료에 사용되는 선형 전자가속기(LINAC)의 작동 원리와 구성 등 의료용 LINAC의 전반을 다룬다. 의료용 LINAC은 전자총에서 발사된 전자를 가속기 튜브 내에서 가속시켜 전자빔을 발생시키고, 이러한 전자빔을 금속 표적에 충돌시켜 발생한 X 선을 인체에 조사하는 원리이다. 최근에는 O-arm, C-arm 등 3-D 촬영을 위한 치료기가 개발됨에 따라, 의료용 LINAC의 전자총, 마그네트론 등을 구동하는데 사용되는 고전압 전원장치 또한 소형화와 고밀도화가 요구되는 추세이다. 본 논문에서는 마그네트론 구동을 위한 고밀도 40kV/100A 음극성 펄스 모듈레이터와 정전압 정전류 제어 및 50kV 절연이 가능한 히터 전원장치를 설계 및 제작하였으며, 9.3GHz, 1.7MW X-Band 마그네트론 연계실험을 통해 고효율 고신뢰성의 동작을 확인하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.504-504
• /
• 2011

최근 디지털 프린팅 기술의 핵심기술로 떠오르고 있는 잉크젯 프린팅 기술은 최근 기존의 문서인쇄 뿐 아니라, 직물 인쇄, 태양전지 등의 다양한 반도체 소자 제조에 널리 활용되고 있으며, 점차 그 응용 분야를 넓혀가고 있다. 특히 thermal 방식의 잉크젯 피린팅 기술은 etching, thin film process, lithography등의 반도체 공정 기술을 이용하여 제작할 수 있기 때문에, 현재 잉크젯 프린팅 기술은 대부분 thermal 방식을 체택하고 있다. 이러한 thermal 잉크젯 프린팅 방법에서는 잉크를 토출시키기 위하여, 전기적 에너지를 열에너지로 전환하는 전자저항막층이 필수적으로 필요하게 되는데, 이러한 전자저항막층은 수백도가 넘는 고온 및 잉크와 접촉으로 인한 부식 및 산화 문제가 발생할 수 있는 열악한 환경에서 사용되므로, Ta, SiN과 같은 보호층을 필수적으로 필요로 한다. 그러나 최근 잉크젯 프린터의 고해상도 고속화, 대면적 인쇄성 등과 같은 다양한 요구 증가에 따라, 잉크젯 프린터의 저전력 구동이 이슈로 떠올라 열효율에 방해가 되는 보호층을 제거할 필요성이 제기되고 있다. 지금까지는 Poly-Si, $HfB_2$, TiN, TaAl, TaN _0.8 등의 물질들이 잉크젯 프린터용 전자저항막 물질로 연구되거나 실제로 사용되어져 왔으나, 이러한 물질들을 보호층을 제거하는 경우 쉽게 산화되거나, 부식되는 문제점을 가지고 있다. 따라서, 기존 전자저항막의 기능을 만족시키면서, 산화나 부식에 대한 강한 내성을 가져 보호층을 제거하더라도 안정적으로 구동이 가능한 하이브리드 기능성(히터 + 보호층)을 가지는 잉크젯 프린터용 전자저항막 물질의 개발이 시급한 실정이다. 본 연구에서는 자기조립특성을 가져 정밀제어가 가능한 원자층증착법(Atomic Layer Deposition)을 이용하여 원자/나노 단위의 미세 구조 컨트롤을 통해 내열 내산화 내부식성 저온도저항계수를 동시에 가지는 다기능성 전자저항막을 설계 및 개발하고자 하였다. 전자저항막 개발을 위하여 우수한 내부식 내산화성을 가지고 결정립 크기에 따른 온도저항계수 조절이 가능한 platinum group metal들과 전기 저항 및 내열성 향상을 위한 물질의 복합구조막을 원자증증착법으로 증착하였다. 또한, 전자저항막 증착시 미세구조와 공정 변수가 내부식성, 내산화성, 그리고 온도저항계수에 미치는 영향을 체계적으로 연구하여, proto-type의 inkjet printhead를 구현하였다.

• Korean Journal of Optics and Photonics
• /
• v.28 no.2
• /
• pp.59-67
• /
• 2017

This paper proposes an asymmetric split-loop resonator with an outer square loop (ASLR-OSL), which can actively control terahertz wave transmission properties while maintaining a high-Q-factor of the asymmetric split-loop resonator (ASLR). An added outer square loop is designed to play the roles of both a metamaterial and a micro-heater, which can control the temperature through a directly applied bias voltage. A vanadium dioxide ($VO_2$) thin film, which exhibits an insulator-metal phase transition with temperature change, is used to control the transmission properties. The proposed ASLR-OSL shows transmission properties similar to those of the ASLR, and they can be successfully controlled by directly applying bias voltage to the outer square loop. Based on these results, an electrically controllable terahertz high-Q metamaterial could be achieved simply by adding a square loop to the outside of a well-known high-Q metamaterial.

• Journal of the Korean Institute of Gas
• /
• v.19 no.4
• /
• pp.41-48
• /
• 2015

The performance characteristics of a scroll expander is the most important variable for the performance of organic Rankine cycle system. In this paper, the performance characteristics of a scroll expander was identified using 1kW class organic Rankine cycle system with various operating conditions. The ORC system is composed of an evaporator, a scroll expander, a condenser and a working fluid feed pump that uses R245fa as working fluid. The hot water temperature was controlled from $80^{\circ}C$ to $115^{\circ}C$ by the 50kW-class electric water-heater. The maximum isentropic efficiency of the scroll expander was measured about 77%, and the shaft power was measured from 0.5 kW to 1.8 kW according to heat source temperatures.

• Journal of IKEEE
• /
• v.25 no.3
• /
• pp.534-539
• /
• 2021

Induction heating method that allows the maximum heating power to be delivered by varying switching frequency in the inductance change of the work coil of induction heater was proposed in this paper. Depending on the type of work piece in the work coil and proximity to the work coil, the resonance frequency of the resonant circuit will be changed. It may be difficult to deliver the maximum power due to the damage of the induced heater element or switching loss depending on the resonance frequency and switching frequency operating relationship. The switching frequency was variable to maintain the maximum power transmission by sensing the heating power due to the change of the resonance frequency. Through the result of the proposed method that can be controlled within the required output change range according to the change of the switching frequency corresponding to the change of the resonance frequency, the induction heater having a variable switching frequency characteristic that can transmit almost constant output power (within 0.43 dB) power efficiency was achieved.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.10
• /
• pp.919-926
• /
• 2013

Experiments were conducted to determine the operating characteristics of a small-scale ORC (organic Rankine cycle) system for various low-temperature heat sources. A small-scale ORC power generation system adopting R-245fa as a working fluid was designed and manufactured. Hot water was used as the heat source, and the temperature was controlled using 110-kW electric resistance heaters that provided temperatures of up to $150^{\circ}C$. An open-drive oil-free scroll expander directly connected to a synchronous generator was installed in the ORC unit. Experiments were conducted by varying the rotational speed of the expander under the same heat source temperature conditions. The factors that influence the performance of the small-scale ORC system were analyzed and discussed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.558-564
• /
• 2021

The water purifier market has increased rapidly in recent years. The welding technology of the evaporator is a key component that determines the level of ice production and the cold water performance of an ice purifier. The finger type evaporator of an ice purifier can remove ice and is divided largely into an instant heat method and a hot gas method. In the hot gas type evaporator, particularly during the production process, the pinhole phenomenon inside the copper pipe and clogging problems occur intermittently when welding high-pressure pipes due to the high-temperature oxygen welding. Its use in a water purifier can cause a problem in that ice and cold water do not form, and repairs cannot be made on site. To solve this problem, in this study, a cap jig was applied to improve the welding defect of the hot gas evaporator. In addition, the oxygen welding flame size was adjusted so that the heat source could be well supplied to the cap jig, and the effectiveness was confirmed through a wave pressure test, a test, and a thermal shock test.

• Journal of Bio-Environment Control
• /
• v.13 no.4
• /
• pp.217-225
• /
• 2004

This study was performed to provide the basic knowledge about the mushroom cultivation facilities. Classified current status of cultivation facilities in Gyeongnam province was investigated by questionnaire. The structure of Pleurotus eryngii cultivation facilities can be classified into the simple and permanent frame type. The simple frame structures were mostly single-span type, on the other hand, the permanent frame structures were more multi-span than simple structures. And the scale of cultivation facilities was very different regardless of structural type. But as a whole, the length, width and ridge height were prevailing approximately 20.0 m, $6.6\~7.0m$ and $4.6\~5.0m$ range, respectively. The floor area was about $132\~160\;m^2$, and floor was built with concrete to protect mushrooms from various harmful infection. The roof slope of the simple and permanent type showed about $41.5^{\circ}\;and\;18.6\~28.6^{\circ}$, respectively. The width and layer number of growing bed for mushroom cultivation were around $1.2\~1.6m$, 4 layers in common, respectively. Most of year round cultivation facilities were equipped with cooler, heater, humidifier, and ventilating fan. Hot water boiler was the most commonly used heating system, the next was electric heater and then steam boiler. The industrial air conditioner has been widely used for cooling. And humidity was controlled mostly by ultra-wave or centrifuging humidifier. But some farmers has been using nozzle system for auxiliary purpose. More then $90\%$ of the mushroom house had the independent environment control system. The inside temperature was usually controlled by sensor, but humidity and $CO_2$ concentration was controlled by timer for each growing stage. The capacity of medium bottle was generally 850 cc and 1100cc, some farms used 800 cc, 950 co and 1,250 cc. Most of mushroom producted has been usually shipped to both circulating company and joint market.