Shape Memory Alloy(SMA) has been used in many engineering fields because of its good characteristics of actuator. For example, SMA wire can be embedded easily in the polymer composite laminate and then be used as actuator for structural control. Since the strain have a significant influence on the electrical resistance of SMA wire, It is a possible to use the SMA wire as a sensor of such physical quantities. In this study, the possibility for the application of Ni-Ti SMA wire as a sensor embedded within a composite laminate is investigated.
Journal of the Korea institute for structural maintenance and inspection
/
v.26
no.2
/
pp.1-8
/
2022
The corrosion of reinforcement is the main reason for the performance degradation of concrete structures. The pre-rusted parts of rebar in concrete structures are vulnerable to the corrosion, especially if the structure is exposed to wet or chlorinated environments. In this study, effects of different curing solution on corrosion behavior of the pre-rusted rebars in the cement composites were investigated. HCl(3%) and CaCl2(10%) solution were utilized to accelerate the pre-rust of the rebar, and each pre-rust condition rebar including reference (RE) were placed in mortar cylinder. Three kinds of samples then were cured in CaCl2 (3%) solution and tap water respectively for 120 days. Electrochemical polarization and half-cell potential measurement were used to monitor the influence of curing water on the corrosion behavior of pre-rusted steel bar in cement composite. The surface morphology and composition of corroded steel bar were analyzed by scanning electron microscope and energy dispersive X-ray diffraction. The results show that the corrosion rates of pre-rusted samples in both curing water are higher than that of non-pre-rusted samples. The corrosion rates of RE, CaCl2 and HCl pre-rusted samples in salt water were 8.14, 4.48, 13.81 times higher than those in tap water respectively, on the 120th day.
A series of the studies on the applied physical properties of domestic species have been conducted last three years. Liriodendron tulipifera, Betula costata, Paulownia coreana were examined on sorption property, thermal property, electric property, acoustic property. Because the same apparatus and experimental procedures were used for all species, their results can be easily comparable. The experiments for sorption property were conducted with 80 mesh wood powder and resulted in their EMC's and sorption isotherms. The thermal conductivity and diffusivity, and electric resistance and volumetric electric resistivity were measured with a thermal-wire device and a high electric resistance meter. The differences of the thermal and electric properties between quarter-and flat-sawn specimens were observed, which was partially attributed to their anatomical differences. An acoustic measurement system was used to evaluate dynamic MOE and internal friction. This paper provides the useful fundamental data for designing a wood structure, correcting a portable resistance-type moisture meter, and acoustic properties of wood.
Kim, Hyung-Sun;Cho, Byung-Won;Yun, Kyung-Suk;Chun, Hai-Soo
Applied Chemistry for Engineering
/
v.7
no.2
/
pp.362-370
/
1996
The performance of The performance of $Li/V_6O_{13}$ cell and the electrochemical properties of polymer electrolyte based on poly(acrylonitrile)[PAN] was investigated. The ionic conductivity of polymer electrolyte showed $2.3{\times}10^{-3}S/cm$ and the compatibility with lithium electrode was excellent. Also, it showed the electrochemical stability up to 4.3V(vs. $Li^+/Li$). The cell reaction of $Li/V_6O_{13}$ was dominated by the interfacial resistance between $V_6O_{13}$ electrode and polymer electrolyte. The diffusion coefficient of lithium ion within $V_6O_{13}$ was $2.7{\times}10^{-9}{\sim}4.2{\times}10^{-8}cm^2/sec$. The utilization of $V_6O_{13}$ active material was 95% at C/8($50{\mu}A/cm^2$) and 82% at C/4($100{\mu}A/cm^2$), respectively.
Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
/
v.23
no.9
/
pp.1-5
/
2009
Disinfection using UV irradiation has been considered to an alternative for chlorination because it does not suffer from disinfection byproducts problem. The aim of this study was to verify if UV irradiation with 368.6[nm] wavelength has a potential to be used a efficient disinfection. UV irradiation was given for 60 minutes to E. coli. which was used as a model microorganism. Remarkable decrease in number of microorganism was not observed for initial 30 minutes, however, 83.3[%] of disinfection efficiency was achieved after 30 minutes of irradiation. Inactivation constant, k was determined to 0.00868[$cm^2$]/([$mW{\cdot}s$]) using kinetic approach.
Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
/
v.23
no.1
/
pp.92-99
/
2009
Deeply-driven ground rod in the rainy season may contact with rainwater and ground water. When surge voltages are applied to the submerged ground rods, the ionization around the ground rods are occurred. Ionization in soil and/or water is affected in dynamic performance of ground rod systems. This work aims at studying the transient performance of ground rod system under impulse voltage using scale model in an electrolytic tank. The potential reduction and energy dispersion caused by ionization were treasured and quantitatively analyzed using the Matlab Program. As a result, the peak voltage at the terminal of ground rod was varied with water resistivity and charging voltage of Marx generator. The potential at the terminal of the ground rod was approximately reduced to a half of the applied voltage just below breakdown voltage. Also the energy more than half of the applied energy was dispersed through the ground rod due to ionization just below breakdown voltage.
Indium Tin Oxide (ITO) thin films have been fabricated by the rf magnetron sputtering technique with a target of a mixture $In_{2}O_{3}$ (90mol%) and $SnO_{2}$ (10mol%). We prepared ITO thin films with substrate temperature 100, 200, 300, 400, $500^{\circ}C$ and post-annealing temperature 300, 400, $500^{\circ}C$. And we analyzed X -ray diffraction patterns, electrical properties, transmission spectra and SEM photographs. As a result, the crystallinity, electrical conductivity and transmittance of ITO thin films were improved with increasing substrate temperature. But, as increasing post-annealing temperature in air, conductivity of the film was decreased. When the ITO thin film was fabricated with substrate temperature of $500^{\circ}C$ and thickness of $3000{\AA}$, its resistivity and transmittance were about $2{\times}10^{-4}{\Omega}cm$ and 85% or more, respectively.
Management of gas safety is becoming important with increasing use of gas facilities. U-safety system is being promoted as part of national management of gas, and thus real-time and in-situ gas sensor should be developed. Detection method for When the gas sensor is installed in gas conduit, explosion may be likely, because hydrocarbon gases is usually used the difference of thermal resistance between reference and working electrode. Therefore, it is required to detect the hydrocarbons, such as $CH_4$ and CO, at room temperature via electrochemically catalytic reaction. In this study, Pt nanoparticle was doped on the porous gold powder by electrolytic plating method, and then it was used as catalytic electrode for CO oxidation. For Pt/PAu electrode, approximately 21% of CO conversion was obtained. It is noted that Pt/PAu electrode could be used to react the oxidation of hydrocarbon gases at room temperature via applying of external voltage.
산소이온전도체 13mol% CaO안정화 $ZrO_{2}$에 대한 $AI_{2}$$O_{3}$의 첨가효과를 살펴보기 위해 출발원료분말을 ($Zr_{0.87}$$Ca_{0.13}$ O$1.87_{1-x}$$AI_{2}$$O_{3}$)x,(x=0,0.01,0.02,0.03,0.05)와 같은 조성이 되도록 공침법으로 합성하고 $1400^{\circ}C$에서 소결시켜, $AI_{2}$$O_{3}$의 첨가에 따른 /grain size의 변화, $AI_{2}$$O_{3}$의 형태 및 존재위치, 소결밀도의 변화, 그리고 저항률의 변화를 살펴보았다. 그 결과, 결정립의 크기는 1mol% A $I_{2}$$O_{3}$첨가까지는 증가하였고, 2mol%첨가이상에서는 입계로 석출하기 시작한 $AI_{2}$$O_{3}$의 pinning효과에 기인되어 감소하였다. 또 1mol% $AI_{2}$$O_{3}$첨가시에 격자상수값의 급격한 감소가 보여지고, 그 이상에서는 변화가 별로 없어 13mol%CaO안정화 $ZnO_{2}$의 고용도한은 최대 1mol%임을 알 수 있었다. 전기전도도 또한 1mol% $AI_{2}$$O_{3}$첨가시에 증가됨을 나타냈다. $ZrO_{2}$에의 고용도한까지의 $AI_{2}$$O_{3}$첨가는 결정립성장을 촉진시키며 밀도값의 증대를 가져오고 전기전도도의 증가를 가져오는 긍정적인 효과를 나타냈다.
Proceedings of the Korean Institute of Surface Engineering Conference
/
2018.06a
/
pp.114-114
/
2018
탄소 재료는 뛰어난 물성에서 다양한 재료로의 응용이 기대되고 있다. 특히, 이종 원소 함유 카본 재료는 전기적 특성과 촉매성의 발현 등 새로운 기능을 카본 재료에 부여할 수 있어서 연료 전지, 에너지 저장, 태양 전지 등에의 응용이 기대되고 있다. 최근, 용액 중의 저온 플라즈마인 솔루션 플라즈마(solution plasma process)를 이용하여 벤젠 용액 등에서 탄소 재료 합성에 성공하였다. 그러나 기존의 연구에서는 솔루션 플라즈마 프로세스를 이용하여 합성한 이종원소 카본은 전도성이 낮아 이종원소의 함유량을 낮추는 고온의 열처리가 필요했다. 따라서 본 연구에서는 우수한 물리적 전기적 특성을 갖는 그래핀(graphene)과 같은 이종 원소 카본 나노시트(heteroatom carbon nanosheets)의 합성 및 메커니즘(mechanism)에 대해 검토하였다. 다양한 이종원소를 포함한 유기용매 안에 바이폴라 펄스 전원에 의한 전압을 두 텅스텐 전극 간에 인가하고, 솔루션 플라즈마를 생성하여 이종원소 카본 재료를 합성했다. 플라즈마 생성은 텅스텐 봉을 전극으로 사용하고 전압을 2.0 kV, 펄스 주파수를 200 kHz, 펄스 폭을 $1.0{\mu}s$, 전극 간 거리를 1.5 mm에서 일정하게 유지하며 200 mL 유기용매 중에서 방전시키는 것으로 재료를 합성했다. 플라즈마 방전 후, 필터을 이용하여 흡인 여과한 뒤 $200^{\circ}C$에서 1 시간 동안 건조 시켰다. 건조 후의 이종원소 카본의 물리적 특성을 원소 분석, X선 회절 법(XRD), 저항률 측정, 투과형 전자 현미경(TEM) 및 라만 분광법, 전자 현미경(SEM), X-선광전자분광기(XPS)등을 이용하여 카본의 형상 및 특성을 분석하였다. 그 결과 다양한 이종원소를 포함한 유기용매 중 2-pyrrolidone을 사용했을 때, 이종 원소 카본 나노시트를 합성하는데 성공하였다. 또한, 이 연구방법을 통해서 솔루션 플라즈마 프로세스를 통한 카본 나노시트 합성의 메커니즘을 규명하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.