• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.5
• /
• pp.332-340
• /
• 2015

Acoustic emission (AE) is an effective nondestructive test that uses transient elastic wave generated by the rapid release of energy within a material to detect any further growth or expansion of existing defects. Over the past decades, because of environmental issues, the use of compressed natural gas (CNG) as an alternative fuel for vehicles is increasing because of environmental issues. For this reason, the importance and necessity of detecting defects on a CNG fuel tank has also come to the fore. The conventional AE method used for source location is highly affected by the wave speed on the structure, and this creates problems in inspecting a composite CNG fuel tank. Because the speed and dispersion characteristics of the wave are different according to direction of structure and laminated layers. In this study, both the conventional AE method and the energy based contour map method were used for source location. This new method based on pre-acquired D/B was used for overcoming the limitation of damage localization in a composite CNG fuel tank specimen which consists of a steel liner cylinder overwrapped by GFRP. From the experimental results, it is observed that the damage localization is determined with a small error at all tested points by using the energy based contour map method, while there were a number of mis-locations or large errors at many tested points by using the conventional AE method. Therefore, the energy based contour map method used in this work is more suitable technology for inspecting composite structures.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.153-158
• /
• 1995

보 및 평판의 진동에 대해서 에너지의 손실은 재료감쇠를 이용한 표면감쇠처리나 지지부에서의 감쇠처리에 의하여 증가될 수 있다. 감쇠재료를 이용한 표면감쇠처리의 예로서 보/평판 표면에 접착되는 감쇠 테이프나 코팅등은 아주 효과적임이 입증되었다. 마찬가지로 지지부 감쇠처리는 점탄성재료의 삽입에 의해서 설명될수 있다[1]. 보/평판의 감쇠에 대한 최근의 많은 연구들은 진동하고 있는 보/평판의 표면에 적용하는 감쇠 테이프 혹은 적층형태의 감쇠 처리방법에 대해서 주로 수행되었다. 일반적으로 표면감쇠처리방법은 진동감소에 아주 효과적이지만 실제 적용상에서 항상 가능한 것은 아니며, 이와 같은 경웨는 지지부 감쇠 처리방법에 의존하게 된다[2]. 감쇠특성을 갖는 점탄성재료를 실제로 적용할 때 보/평판의 유한한 길이가 점탄성재료로 지지되며 점탄성재료의 물성치와 치수에 따라서 계의 모우드 매개변수(고유진동수, 계의 손실계수 그리고 모우드형상)가 크게 달라진다. 그리고 이와 같은 계에 대해서는 지지부의 거동보다는 전체 시스템의 고유진동수와 손실계수 그리고 보 영역에서의 모우드 형상에 더 관심이 있으므로 지지부 영역을 집중매개변수(lumped parameter)로 나타내어 계를 해석할 수 있다. 일반적으로 보와 평판의 경계에서는 병진 및 회전방향의 강성 뿐만 아니라 두 강성사이에 연성효과도 동시에 발생하게 되므로 이 항을 고려하여 계를 모델링해야 한다. 본 연구에서는 우선 점탄성 재료에 의한 지지부영역의 등가 강성계수들을 구하고 경계에 강성행렬을 갖는 보의 등가시스템을 얻는다. 그리고 등가시스템의 주파수방정식으로부터 모우드 매개변수에 대한 지지부의 영향을 살펴본다. 또한 시스템이 비교적 복잡한 사각 평판의 진동에 대해서도 동강성행렬법(dynamic stiffness matrix method)을 이용하여 해석하고자 한다. 수준임이 입증되었다. 본 연구의 결과를 토대로우리나라 젊고 건강한 남성에게 적합한 무게상수는 작업자군에 대하여 25.05kg, 학생군에 대하여 20.24kg 으로 나타나 이는 미국 NIOSH 안전기준과 대체로 일치함을 발견하였다.ive structures utilized in Client/server architecture for distribution and cooperative processing of application between server and client this study presents two different data management methods under the Client/server environment; one is "Remote Data Management Method" which uses file server or database server and. the other is "Distributed Data Management Method" using distributed database management system. The result of this study leads to the conclusion that in the client/server environment although distributed application is assumed, the data could become centralized (in the case of file server or database server) or decentralized (in the case of distributed database system) and the data management method through a distributed database system where complete responsi

• Land and Housing Review
• /
• v.2 no.3
• /
• pp.287-297
• /
• 2011

This paper presents the results of performance verification tests of the isolated flat plate apartment building with the laminated rubber bearings. The shaking table test is carried out in CABR(China Academy of Building Research) with two 1/10 scale isolation and non-isolation models under 4 excitation waves. The shaking table test is proceeding from x axis, y axis and x+y axis with different amplitude of acceleration values. The results show that, to non-isolated model, the natural vibration period is remarkably decreased and entered non-linear condition after moderate earthquake. Its accelerations become lager with increasing storey number and completely collapsed under large earthquake. The inter-storey shifts largely exceed the limit values of regulated displacement angles. But to isolated model, the natural vibration period of isolated modal is almost the same in all conditions and still in its elastic condition. The earthquake loading is greatly reduced and the accelerations of superstructure are greatly reduced. The inter-storey drifts are very small and can be neglected. The isolated model is in translational state and can be seen as a rigid whole. The displacements of isolation layer are in the allowable range. This experiment demonstrates that the seismic isolation is very effective to mitigate the influence of earthquake on structures and it is possible to increase the serviceability due to decrease the floor acceleration. facilities from their good states that is superior to non-isolated structure.

• Economic and Environmental Geology
• /
• v.37 no.5
• /
• pp.533-541
• /
• 2004

A steadily consolidated conglomerate formation (CCF) is developed thickly around Tabjeong-ri and Janghang-ri to the east of Tohamsan, Gyeongju City. The CCF has been regarded to a basal conglomerate, Cheonbug Conglomerate, of the Yonil Group by Tateiwa (1924). Son et al. (2000) correlated the CCF to the Songjeon Formation, which occupies the southwestern block of Tertiary Waup Basin. However, the Songjeon Formation stratigraphically does not face to the extension of the CCF. OSL (Optically Stimulated Luminescence) data on the reddish brown to bluish gray psammitic layers, which are intercalated in the CCF, yielded to 85∼92 ka. Therefore, the age of CCF constrains to the last interglacial stage (MIS 5c-5e) rather than the Early Miocene Cheonbug Conglomerate. The Late Pleistocene Tohamsan Formation (TF) is newly named to the CCF and is subdivided to megabreccias and boulders. A rectangular basin, in which the TF is accumulated, is bounded by Oedong and Yonil faults (segments of Yonil Tectonic Line) and is given a name of Toham Basin. Neotectonically, Pliocene EW-transpression gave an effect of the top-up-to-the-west reverse faulting and the accompanied normal fault movement during the last interglacial age (ca. 100 ka). The basin is graben type, in which basin fills are composed of collapsed colluvial deposits, TF.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.10
• /
• pp.1201-1206
• /
• 2013

Defects that occur during the manufacturing process or operation of a wind turbine blade have a great influence on its life and safety. Typically, defects such as delamination, pore, wrinkle and matrix crack are found in a blade. In this study, the detectability of the pores, a type of defect that frequently occur during manufacturing, was examined from the full field strain distribution determined with the image correlation technique. Pore defects were artificially introduced in four-ply laminated GFRP composites with $0^{\circ}/{\pm}45^{\circ}$ fiber direction. The artificial pores were introduced in consideration of their size and location. Three different-sized pores with diameter of 1, 2 and 3 mm were located on the top and bottom surface and embedded. By applying static loads of 0-200 MPa, the strain distributions over the specimen with the pore defects were determined using image correlation technique. It was found the pores with diameter exceeding 2 mm can be detected in diameter.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.2
• /
• pp.77-83
• /
• 2006

Ultrasonic nonlinearity has been considered as a solution for the detection of microcracks or interfacial delamination in a layered structure. The distinguished phenomenon in nonlinear ultrasonics is the generation of higher-order harmonic waves during the propagation. Therefore, in order to quantify the nonlinearity, the conventional method measures a parameter defined as the amplitude ratio of a second-order harmonic component and a fundamental frequency component included in the propagated ultrasonic wave signal. However, its application In field inspection is not easy at the present stage because no standard methodology has yet been made to accurately estimate this parameter. Thus, the aim of this paper is to propose an advanced signal processing technique for the precise estimation of a nonlinear ultrasonic parameter, which is based on power spectral and bispectral analysis. The method of estimating power spectrum and bispectrum of the pulse-like ultrasonic wave signal used in the commercial SAM (scanning acoustic microscopy) equipment is especially considered in this study The usefulness of the proposed method Is confirmed by experiments for a Newton ring with a continuous air gap between two glasses and a real semiconductor sample with local delaminations. The results show that the nonlinear parameter obtained tv the proposed method had a good correlation with the delamination.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.30 no.2
• /
• pp.145-151
• /
• 2014

Purpose: The purpose of this study was to investigate the microleakage in class II cavity resin restorations used with resin-modified glass ionomer (RMGI) lining material depending on two different applying methods; classical delivery method using a dental explorer and a specially designed rotating bur. Materials and Methods: A total thirty-six extracted teeth were prepared with a class II proximal box, and randomly divided into three groups: 1) control group with no lining added and the proximal box restored (Group I), 2) the second group used RMGI as a lining material which was spread with an explorer (Group II), 3) the third group used a specially designed rotating bur to thin out RMGI (Group III). All teeth were restored with the same manner using incrementally placed resin composite. All 36 teeth were prepared and sectioned for the dye penetration test, and observed with a stereomicroscope for scoring the dye penetration. Results: When RMGI liners were used, both groups using an explorer and the special bur with the liner had significantly less microleakage than the control group with no liner (P < 0.05). The 50% of the group with RMGI liner using the bur showed no microleakage under a dye penetration test whereas all the teeth in control group showed microleakage of different degrees. However, there was no statistically significant difference between Group II and Group III. Conclusion: RMGI is an effective lining material to decrease microleakage in class II composite resin restorations regardless of applying methods.

• Composites Research
• /
• v.34 no.5
• /
• pp.317-322
• /
• 2021

When a complex load such as torsion, low-speed impact, or fatigue load is applied, the properties in the thickness direction are weakened through microcracks inside the material due to the nature of the laminated composite material, and delamination occurs. To prevent the interlaminar delamination, various three-dimensional reinforcement methods such as Z-pinning and stitching, and structural health monitoring techniques that detect the microcrack of structures in real time have been continuously studied. In this paper, the single-lap joints with I-fiber stitching process were manufactured by a co-curing method and their strengths and failure detection capability were evaluated. AE and electric resistance method were used for detection of crack and failure signal and electric circuit for signal analysis was manufactured, and failure signal was analyzed during the tensile test of a single-lap joint. From the experiment, the strength of the single lap joint reinforced by I-fiber stitching process was improved by about 44.6% compared to the co-cured single lap joint without reinforcement. In addition, as the single-lap joint reinforced by I-fiber stitching process can detect failure in both the electrical resistance method and the AE method, it has been proven to be an effective structure for failure monitoring as well as strength improvement.

• Composites Research
• /
• v.32 no.5
• /
• pp.199-205
• /
• 2019

The composite material has the advantage that the fibers can be arranged in a desired direction and can be manufactured in one piece. However, micro voids can be formed due to micro air, moisture or improper curing temperature or pressure, which may cause the deterioration in mechanical strength. In this paper, the composite panels with different thicknesses were made by varying the curing pressure in an autoclave vacuum bag process and their microporosities were evaluated. Microporosity was measured by image analysis method, acid digestion method, and combustion method and their correlation with ultrasonic attenuation coefficient was analyzed. From the test results, it was found that the acid digestion method had the highest accuracy and the lower the curing pressure, the higher the microporosity and the ultrasonic attenuation coefficient. In addition, the microporosity and the ultrasonic attenuation coefficient were increased as the thickness of the composite panel was increased at the same curing pressure.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.3
• /
• pp.25-29
• /
• 2022

Recently, the importance of electronic packaging technology has been attracting attention, and heterogeneous integration technology in which chips are stacked out-of-plane direction is being applied to the electronic packaging field. The 2.5D integration circuit is a technology for stacking chips using an interposer including TSV, and is widely used already. Therefore, it is necessary to make the interposer mechanically reliable in the packaging process that undergoes various thermal processes and mechanical loadings. Considering the structural characteristics of the interposer on which several thin films are deposited, thermal stress due to the difference in thermal expansion coefficients of materials can have a great effect on reliability. In this study, the mechanical reliability of the metal pad for wire bonding on the silicon interposer against thermal stress was evaluated. After heating the interposer to the solder reflow temperature, the delamination of the metal pad that occurred during cooling was observed and the mechanism was investigated. In addition, it was confirmed that the high cooling rate and the defect caused by handling promote delamination of the metal pads.