• Current Research on Agriculture and Life Sciences
• /
• v.5
• /
• pp.75-80
• /
• 1987

We investigated physico-chemical properties of hard wheat flours for frozen yeast-raised breadmaking and freezing stability of frozen dough prepared by the straight no-time method. The general Composition of wheat flours were : moisture ; 14.0%, ash ; 0.48%. protein ; 13.15%, and dry gluten ; 13.43%. In farinograph data, development time and water absorption were 5.5 mimutes and 62 %, respectively. Amylograph maximum viscosity was 500 BU. Resistance to extention increased with the time and their extensibility decreased in the extensigraph data. From these results obtained from these physico-chemical properties, it was confirmed that the used wheat flours were most suitable for bread-baking. Considering effect of gassing power on cold storage period and fermentation time, it was effective that dough temperature should be adjusted to $20^{\circ}C$ in order to decrease freezing injury and maintain freezing stability.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.2
• /
• pp.214-221
• /
• 2024

The present study concerns the resistance of calcium aluminate cement (CAC) to steel corrosion. The corrosion behavior of steel, chloride binding/buffering and chloride transport were evaluated in order to predict the risk of steel corrosion. The CAC mortar exhibited no corrosion on steel, irrespective of the curing temperature and CAC types, whereas ordinary Portland cement (OPC) showed a severe corrosion on the steel surface. The chloride binding capacity of CAC found to be was lower than that of OPC, yet buffering capacity against pH decrease was found to be significantly higher in the CAC paste. Furthermore, chloride ingress at all depths was found to be reduced in CAC, thereby reducing the risk of corrosion.

• Journal of the Korean Vacuum Society
• /
• v.21 no.3
• /
• pp.142-150
• /
• 2012

In this Study, Mo back electrode were deposited as the functions of various working pressure, deposition time and plasma per-treatment on sodalime glass (SLG) for application to CIGS thin film solar cell using by DC sputtering method, and were analyzed Mo change to $MoSe_2$ layer through selenization processes. And finally Mo back electrode characteristics were evaluated as application to CIGS device after Al/AZO/ZnO/CdS/CIGS/Mo/SLG fabrication. Mo films fabricated as a function of the working pressure from 1.3 to 4.9mTorr are that physical thickness changed to increase from 1.24 to 1.27 ${\mu}m$ and electrical characteristics of sheet resistance changed to increase from 0.195 to 0.242 ${\Omega}/sq$ as according to the higher working pressure. We could find out that Mo film have more dense in lower working pressure because positive Ar ions have higher energy in lower pressure when ions impact to Mo target, and have dominated (100) columnar structure without working pressure. Also Mo films fabricated as a function of the deposition time are that physical thickness changed to increase from 0.15 to 1.24 ${\mu}m$ and electrical characteristics of sheet resistance changed to decrease from 2.75 to 0.195 ${\Omega}/sq$ as according to the increasing of deposition time. This is reasonable because more thick metal film have better electrical characteristics. We investigated Mo change to $MoSe_2$ layer through selenization processes after Se/Mo/SLG fabrication as a function of the selenization time from 5 to 40 minutes. $MoSe_2$ thickness were changed to increase as according to the increasing of selenization time. We could find out that we have to control $MoSe_2$ thickness to get ohmic contact characteristics as controlling of proper selenization time. And we fabricated and evaluated CIGS thin film solar cell device as Al/AZO/ZnO/CdS/CIGS/Mo/SLG structures depend on Mo thickness 1.2 ${\mu}m$ and 0.6 ${\mu}m$. The efficiency of CIGS device with 0.6 ${\mu}m$ Mo thickness is batter as 9.46% because Na ion of SLG can move to CIGS layer more faster through thin Mo layer. The adhesion characteristics of Mo back electrode on SLG were improved better as plasma pre-treatment on SLG substrate before Mo deposition. And we could expect better efficiency of CIGS thin film solar cell as controlling of Mo thickness and $MoSe_2$ thickness depend on Na effect and selenization time.

• Journal of the Korean Magnetics Society
• /
• v.15 no.5
• /
• pp.270-275
• /
• 2005

Dust cores (compressed powder cores) of $Fe-6.0wt\%Si$ alloy with a size of $35\~180\;{\mu}m$ in diameter have been prepared by phosphate coatings and annealings at $600\~900^{\circ}C$ for 1 h in nitrogen atmosphere. Further the magnetic and mechanical properties of the powder cores were investigated. As a general trends, the compressive strength and core loss decreased with the increase in annealing temperature. When annealed at $800^{\circ}C$, the compressive strength was 15 kgf, the permeability and quality factor were 74 and 26, respectively. Moreover the core loss at 50 kHz and 0.1 T induction was $750\;mW/cm^3$, and the percent permeability under the static field of 50 Oe was estimated to be about 78. In addition, the cut-off frequency in the cure representing the frequency dependence of effective permeability was measured to be around 200 kHz. These properties of the $Fe-6.0wt\%Si$ alloy dust cores could be considered to be due to the good insulation effect of iron-phosphate coats, the decrease in magnetocrystalline anisotropy and saturation magnetostriction and the increase in electric resistivity.

• Food Science and Preservation
• /
• v.6 no.2
• /
• pp.161-166
• /
• 1999

In order to increase the Korean wheat-cultivators' incomes as well as to promote their consumptions, the native wheat of 11 varities (Chokwangmil, Geurumil, Eunpamil, Tapdongmil, Woorimil, Olgeurumil, Alchanmil , Gobunmil, Geungangmil Seodunmil and Suwon 265) were investigated on dough properties to compared with those of two imported wheat varieties, DNS (Dark Northern Spring Wheat) and ASW (Austrlian Standard White). In dough stickiness, Chokwangmil was highest as 81.78, and the mean value of native wheat was 53.98 g. ASW and DNS showed the stickiness values of 58.7 g and 52.9 g, respectively. Tapdongmil was highest in the tensile tone of dough as 87.6 g. In the texture test, the highest elasticity, gumminess, firmness and chewiness were observed in Woorimil as values of 0.980, 1,022.8, 1,562.7 and 1,001.9, respectively, while the highest cohesiveness and adhesiveness were obtained from Suwon 265 and Geurumil, respectively, as 0.710 and -609.4. In amylogram properties, the initial gelatinization temperature was ranged from 65$^{\circ}C$ to 69$^{\circ}C$, and maximum, minimum and final viscosities were highest in Woorimil as 1,140, 1,100 and 1,730 BU, respectively. In farinogram, water absorption rate was highest in Suwon 265 as 65.1%, which required the longest dough arrival time of 3.5 min. Dough developing time, weakening and stability were longest in Gobunmil as 9.7. 32.1 and 29.9 min., respectively. The resistance of dough was highest in Olgeurumil as 110 BU.

• Journal of the Korean Magnetics Society
• /
• v.13 no.3
• /
• pp.109-114
• /
• 2003

The purpose of this study Is to investigate the effect of $V_2$O$_{5}$ addition on the microstructures and magnetic properties of 7.7${\times}$4.5${\times}$1.0 mm sized multi-layer chip inductors prepared by the screen printing method using 0∼0.5 wt％ $V_2O_{5}$-doped NiCuZn ferrite pastes. With increasing the $V_2O_{5}$ content, the exaggerated grain growth of ferrite layers was developed due to the promotion of Ag diffusion and Cu segregation into the grain boundaries oi ferrites, which affected significantly the magnetic properties of the chip inductors. After sintering at $900^{\circ}C$, the inductance at 10 MHZ of the 0.5 wt％ $V_2O_{5}$-doped chip inductor was 3.7 ${\mu}$H less than 4.2 ${\mu}$H of the 0.3 wt% $V_2O_{5}$-doped one, which was thought to be caused by the residual stress at the ferrite layers increased with the promotion of Ag diffusion and Cu segregation. The quality factor of the 0.5 wt% $V_2O_{5}$-doped chip inductor decreased with increasing the sintering temperature, which was considered to be caused by the electrical resistivity of the ferrite layer decreased with the promotion of Ag/cu segregation at the grain boundaries and the growth of the mean grain size of ferrite due to exaggerated grain growth of ferrite layers.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.1
• /
• pp.37-42
• /
• 2021

The effect of chemical composition on the structural and thermal properties of TiZrN thin films was studied. As the Zr fraction in the deposited TixZr1-xN (x = 0.87, 0.82, 0.7, 0.6, and 0.28) increased, microstructural changes consisted of reduction in the grain size and a gradual transition from columnar structure to granular structure were observed. In addition, it was also confirmed that a gradual crystal phase transition from TiN to TiZrN has occurred as the Zr fraction increased up to 0.4. After heat treatment at 900℃, Ti0.82Zr0.18N and Ti0.7Zr0.3N layers were converted to a form in which rutile phase TiO2 and TiZrO4 oxides coexist, while Ti0.6Zr0.4N layer was converted to TiZrO4 oxide. Among the five compositions of TiZrN films, the Ti0.6Zr0.4N showed the best high temperature stability and produced a significant enhancement in the thermal oxidation resistance of Inconel 617 through suppressing the surface diffusion of Cr caused by thermal oxidation of the Inconel 617 substrate.

• Journal of Life Science
• /
• v.19 no.9
• /
• pp.1226-1231
• /
• 2009

Enzyme substitution with recombinant phenylalanine ammonia-lyase (PAL, EC 4.3.1.5) is currently being explored for treatment of phenylketonuria (PKU), an autosomal recessive genetic disorder with mutations of the gene encoding phenylalanine-4-hydroxylase (EC 1.14.16.1). However, oral administration of PAL is limited because of proteolytic digestion in the gastrointestinal tract. The aim of this study was to determine the biochemical properties of PAL and delinate the susceptibility of wild-type PAL to pancreatic proteolysis by exploring several mutants, and to develop therapeutic drugs with PAL for PKU. The specific activity of PAL was assayed and its optimal pH, temperature stability, and intestinal protease susceptibility were investigated. Its $V_{max}$ values for phenylalanine and tyrosine were 1.77 and $0.47{\mu}mol$/ min/mg protein, respectively, and its $K_m$ values were $4.77{\times}10^{-4}$ and $4.37{\times}10^{-4}\;M$, respectively. PAL showed an optimal pH at 8.5, corresponding to the average pH range of the small intestine. It showed no loss of activity at $-80^{\circ}C$ for 5 months and possessed 93.4% of its activity under $4^{\circ}C$ for 4 wks. PAL was susceptible to chymotrypsin digestion and, to a lesser extent, to trypsin, elastase, carboxypeptidase A, and B. The trypsin and chymotrypsin cleaving sites were mutated to investigate protection from pancreatic digestion and the specific activities of these mutants were evaluated. The six mutants displayed low specific activities compared to the wild-type, suggesting that the primary trypsin and chymotrypsin cleaving sites may be essential for catalytic reaction. The PAL mutants could therefore be applied as a pretreatment modality without susceptibility to proteolytic attack, however, additional modification for enhancing enzymatic activity is needed to reduce the Phe levels effectively.

• The korean journal of orthodontics
• /
• v.36 no.5
• /
• pp.349-359
• /
• 2006

Objective: Nickel-titanium alloy wire possesses excellent spring-back properties, shape memory and super-elasticity. In order to adapt this wire to clinical use, it is necessary to bend as well as to control its super-elastic force. The purpose of this study is to evaluate the effects of heat treatment on the load-deflection properties and transitional temperature range (TTR) of nickel-titanium wires. Methods: Nickel-titanium wires of different diameters ($0.016"\;{\times}\;0.022"$, $0.018"\;{\times}\;0.025"$ and $0.0215"\;{\times}\;0.028"$) were used. The samples were divided into 4 groups as follows: group 4, posterior segment of archwire (24 mm) without heat treatment; group 2, posterior segment of archwire (24 mm) with heat treatment only; group 3, anterior segment with bending and heat treatment; group 4, anterior segment with bending and 1 sec over heat treatment. Three point bending test was used to evaluate the change in load-deflection curve and obtained DSC (different scanning calorimetry) to check changes in $A_f$ temperature. Results: In the three point bending test, nickel-titanium wires with heat treatment only had higher load-deflection curve and loading and unloading plateau than nickel-titanium wires without heat treatment. Nickel-titanium wires with heat treatment had lower Af temperature than nickel-titanium wires without heat treatment. Nickel-titanium wires with heat treatment and bending had higher load-deflection curve than nickel- titanium wires with heat treatment and nickel-titanium wires without heat treatment. Nickel-titanium with heat treatment of over 1 sec and bending had the highest load-deflection curve. Nickel-titanium wires with heat treatment and bending had lower Af temperature, Nickel-titanium wires with heat treatment of over Af sec and bending had the lowest Af temperature. Conclusion: From the results of this study, it can be stated that heat treatment for bending of Nickel-titanium wires does not deprive the superelastic property but can cause increased force magnitude due to a higher load-deflection curve.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.30 no.4
• /
• pp.543-549
• /
• 1997

The problems in the existing modeling rules for fishing nets, especially in the Tauti's rule which had been used most commonly, were investigated and it was found that the rules could not give a good similarity between the prototype and model nets because they din neither analyze the flow resistance of nets accurately nor decide the ratio of flow velocity between the two nets properly. Thus, the modeling rule was newly derived by regarding the nets as holey structures sucking water into their mouth and then filtering water through their meshes as in the previous paper. The similarity conditions obtained, between the two nets distinguished by subscript 1 and 2, are as follows; $$\frac{d_2}{d_1}=\sqrt{\frac{l_2}{l_1}},\;\frac{N_2}{N_1}=(\frac{d_1}{d_2})^{1.5}\frac{L_2}{L_1},\;\varphi_1=\varphi_2,\;\frac{d_{r2}}{d_{r1}}=\sqrt{\frac{L_2{(\rho_{r1}-\rho_{w1})}}{{L_1{(\rho_{r2}-\rho_{w2})}}$$ $$\frac{N_{a2}}{N_{a1}}=\frac{W_{a1}}{W_{a2}}(\frac{L_2}{L_1})^2,\;\nu_1=\nu_2\;and\;\frac{R_2}{R_1}=(\frac{L_2}{L_1})^2$$, where L is the length of nettings, d the diameter of netting twines, 2l the mesh size, $2\varphi$ the angle between two adjacent bars, N the number of meshes at the sides of nettings, $d_r$, the diameter of ropes, $\rho_r$, the specific gravity of ropes, $W_a$ the weight in water of one piece of float or sinker, $N_a$ the number of floats or sinkers, $\nu$ the flow velocity, and R the flow resistance of net. In the case where the model experiments aim at investigating the influence of weight in water of nettings on their shapes in nets subjected to the water flow of very low velocity, however, the following condition is added; $$\frac{\rho_2-\rho_{w2}}{\rho_1-\rho_{w1}}=\frac{d_1}{d_2}$$ where $\rho$ is the specific gravity of netting twines.