• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.2
• /
• pp.110-116
• /
• 2013

A concrete structure has become bigger and higher because of development of construction technology and a change in construction environment. Also it tends to focus on repairing, reinforcement and exterior in harmony with environment for structure maintenance and performance improvement. The research is about eco friendly durable painting applicable to concrete structure using civil and architecture. it purpose to improve external beauties and durable problems due to flexibility by variation of temperature, adhesion of exterior wall, crack and delamination in existing organic and mineral painting. For those problems, we made a eco friendly pre-paint that is made with preliminary treatment mixture as a highly enriched waterproof agent and adhesive increasing agent in preprocessing mixture. Then we performed an experiment on durability of prevention neutralization of concrete, durability abrasion, hiding power, adhesion, temperature resistance and resistance to chemical attack. The result of an experiment shows that hiding power is over 0.96 in standard test, durability abrasion test got higher value 1mg than water paint 75mg and tensile strength is 6 times higher than standard waterproof specification.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.3
• /
• pp.130-134
• /
• 2017

In this study, numerical simulation was performed to focus on optimized process condition for obtaining a long-term growth and high quality SiC crystal. It could be optimized by considering the change of fluid and a carbon flow in the Si melt added with 40 % Cr. The Crystal Growth Simulator ($CGSim^{TM}$, STR Group Ltd.) was used as a numerical simulation. It was confirmed that many parameters such as temperature, rotation speed of seed crystal and crucible, and seed position during the crystal growth step had a strong influence on the speed and direction of solution flow for uniform temperature gradient and stable crystal growth. The optimized process condition for the solution growth of SiC crystal was successfully exhibited by adjusting various process parameters in the numerical simulation, which would be helpful for real crystal growth.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.4
• /
• pp.58-66
• /
• 1990

A series of test was performed measuring the failure strength and failure mode of Gr/Pi, $[0^{\circ}/45^{\circ}/90^{\circ}/-45^{\circ}]_s$ laminate containing a single pin loaded hole. The finite element method is applied to calculate the stress distribution in the laminates, then the failure load and the failure mode were predicted by means of the characteristic length. 12 different geometric variations were developed to analyze the effects of the ratio of specimen width to hole diameter (W/d) and ratio of edge distance to hole diameter (L/d). X-Ray of NDE methods were utilized in finding out the initial defects, damage and the fracture mechanism, and SEM(Scanning Electron Microscopes) was used the evaluation of the fracture mechanism and crack propagation around hole under tension pin loading. $[0^{\circ}/45^{\circ}/90^{\circ}/-45^{\circ}]_s$ laminate are found to be most sensitive to W/d but not so influenced by L/d. The failure mode and tensile strength predicted by the model show agreement with experiment data for pin loading bolted jointed test except range of $L/d{\leqq}3$.

• Journal of the Korea Concrete Institute
• /
• v.23 no.1
• /
• pp.121-127
• /
• 2011

In this study, possible use of indigenous natural loess (Hwangtoh) as a new binding material via geopolymerization process is examined. Hwangtoh pastes with four different mix proportions of varying alkali liquid concentrations (6 M, 8 M) and the constituents of the binder as well as the alkali liquid at a constant liquid-to-binder ratio of 0.55 were prepared. Analysis of the natural loess (Hwangtoh) paste was carried out as follows : 1) Measurement of compressive strength and weight of cubic specimens versus curing time; 2) Analysis by X-ray diffraction (XRD) and scanning electron microscope (SEM) about reaction product; 3) Porosity analysis of hardened Hwangtoh paste. The result showed that it is possible to prepare Hwangtoh paste with 29.1 MPa at the age of 7 day by using alkali solution (made as 1 : 4.5 the mass ratio of liquefied $Na_2SiO_3$ and NaOH solution and applying the curing temperature of $60^{\circ}C$). Compressive strength development with respect to the degree of moisture evaporation from the paste seems to be independent of curing temperature. Therefore, it seems that higher early strength of the paste specimens cured at higher temperature can be attributed to both higher rate of reaction and moisture evaporation.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.3
• /
• pp.276-285
• /
• 2020

In this study, accelerated chloride diffusion tests were performed on OPC(Ordinary Portland Cement) and FA(Fly Ash) concrete considering three levels o f W/B(Water to Binder) ratio o n 1,095 curing days. The accelerated chloride diffusion coefficient and the passed charge were evaluated in accordance with Tang's method and ASTM C 1202, and the resistance performance to chloride attack improved over time. FA concrete showed excellent resistance performance against chloride penetration with help of pozzolanic reaction. As the result of the passed charge, FA concrete showed durability improvement, "low" grade to "very low" grade, but OPC concrete changed "moderate" grade to "low" grade at 1,095 curing days. After assuming the design variables used for durability design as normal distribution functions, the service life of each case was evaluated by the probabilistic analysis method based on MCS(Monte Carlo Simulation). In FA concrete, the increase of probability of durability failure was lower than that of OPC concrete with increasing time, because the time-dependent coefficient of FA concrete was up to 3.2 times higher than OPC concrete. In addition, the service life by probabilistic analysis was evaluated lower than the service life by deterministic analysis, since the target probability of durability failure was set to 10%. It is considered that more economical durability design will be possible if the mo re suitable target probability of durability failure is set for various structures through researches on actual conditions and indoor tests under various circumstances.

• Journal of Korean Society of Forest Science
• /
• v.108 no.4
• /
• pp.562-573
• /
• 2019

In a cable yarding system, a small-scale tower yarder attached to a farm tractor wasdeveloped and used for small-diameter tree harvesting operations. Based on this design, improvement of traction performance was required for medium- and large-diameter tree harvesting operations. In this study, the mechanical transmission employed for the tower yarder was modified into ahydro-mechanical transmission system. Maximum traction forces, including tractor engine speed and hydraulic power pressure, were investigated, and comparisons were made between the mechanical and hydro-mechanical transmission systems. Six tractor engine speeds (1,200, 1,400, 1,600, 1,800, 2,000, and 2,200) and three levels of power transmission mechanism pressure (4.9, 6.9, and 8.8 MPa) were investigated in the two different transmission systems. Results showed a maximum traction force of 15,146.6 N at an engine rotation speed of 757 rpm in the current mechanical transmission system, and 36,140.0 N at anengine rotation speed of 1,575 rpm in the modified hydro-mechanical transmission system. The maximum traction forces for the hydro-mechanical transmission were 2.4 times greater than those of the mechanical transmission, and may therefore be applicable to medium and large-diameter tree harvesting operations. Thus,as a modified version of the conventional transmission system, the new hydro-mechanical transmission system may be cost-effective for use in large-scale cable yarding operations. In the future, however, it will be necessary to investigate problems that may arise from field application tests.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.32 no.3
• /
• pp.149-157
• /
• 2016

Tooth preparation design is essential for successful laminate veneer treatment. Preservative tooth preparation limited on enamel, supra-margin advantageous for plaque control, and maintaining contact points known as a standard concept. However, the tooth preparation design has been the controversial issue. In biomechanical considerations, the incisal coverage should be decided on esthetic needs and necessity for the anterior guidance reconstruction. In occasion for sufficient enamel thickness, preparation can prolong to the palatal side but not recommended at palatal concavity. Elongation to contact point is selective option according to the cases. If an old resin restoration located at contact area, laminate veneer should cover over half area of that after surface treatment. The laminate veneer can be also selected at a partially discolored tooth root canal therapy (RCT) and at this occasion, the fiber-reinforced composite (FRC) posts are recommended.

• Journal of Navigation and Port Research
• /
• v.40 no.1
• /
• pp.1-6
• /
• 2016

This study was conducted on a circulation system which can recycle waste water from EGCS(Exhaust Gas Cleaning System) using a wet scrubber that is used to treat air pollutants from ships. Though we developed a water treatment system that could remove effectively particulate matters and dispersed oil included in cleaning water for Ship Exhaust Gas Recycle System(DePM & DeSOx), we found that it is difficult to treat minutely dispersed oil only by means of centrifugal-typed purifier. Therefore, to this system, we applied a coalescer that coalesces emulsified minute oil particles in the 2nd phase of dispersion state after being filtered through the centrifugal-typed purifier. After we treated cleaning water drained out of Ship Exhaust Gas Recycle System(DePM & DeSOx) by using both purifier and coalescer, we found that particulate matters and dispersed oil were removed more than 55% and 99%, respectively, in comparison with those contained in cleaning water influent. Putting the results together, we conclude that the treated cleaning water can be recycled as normal cleaning water if this cleaning water treatment system is employed by the wet cleaning tower system for the reduction of air pollutants from ships.

• The KIPS Transactions:PartD
• /
• v.11D no.3
• /
• pp.671-682
• /
• 2004

As new and diverse information technologies are being introduced and software complexity is increased, software development cost and efforts are also sharply increased. Component-Based Development (CBD) technology is appealing as a new way to reduce the cost and effort by increasing reusability and maintainability. Component in CBD has variability infernally which enables customization of the component within the specific domain. A component user can easily set up internally variability parts though Required interface which is provided by the component. Enterprise JavaBeans (EJB) is utilized as a commercial standard to implement Java-based components. However, EJB constructs are limited in directly implementing Required interfaces of coarse-grained components［8］. In this paper, we define Required interface and propose interface-storage technique, class-storage technique, interface-generation technique, and Plug -in technique for implementing required interface of component. Interface-storage technique stores variable value in Required interface and class-storage technique take the Bean containg variability as Required interface without modification of component model. Interface-generation technique generates new Bean which takes the role of Required interface for component variability and Plug-in technique sets up component variability that component user plugged-in variable part externally The proposed four techniques conform to the semantics of CBD component interface and enable the implementation of high quality components.

• The KIPS Transactions:PartA
• /
• v.13A no.6 s.103
• /
• pp.545-554
• /
• 2006

Although the current Web search engines provide tremendous information, it is hard to find right information among the huge information. Users need to spend extra time to filter out unnecessary information. In order to overcome the limit of current Web search engines, Semantic Web was developed to provide efficient search, integration, and reuse of information by structuring semantic information from Web resources. In this paper, an elementary education contents retrieval system using Semantic Web is proposed. The proposed system emphasizes history contents that have high relevancy among data. For construction of the proposed system, ontology is proposed first for elementary study contents and ontology for historical contents is proposed for easy access to those contents using semantic relation among them. Based on the ontology, the proposed system is designed and implemented. The proposed system has the following characteristics. First, the system provides various query formats in detail so that search results can be refined efficiently. Second, the system presents only semantically information connected with key words or including key words using study contents ontology. Finally, the proposed system can increase study effects by presenting various contents that are related with query by users.