• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.8
• /
• pp.22-26
• /
• 2012

This paper introduces a 2.5-Gb/s optical receiver implemented in a standard 1P4M 0.18um CMOS technology for the applications of active optical HDMI cables. The optical receiver consists of a differential transimpedance amplifier(TIA), a five-stage differential limiting amplifier(LA), and an output buffer. The TIA exploits the inverter input configuration with a resistive feedback for low noise and power consumption. It is cascaded by an additional differential amplifier and a DC-balanced buffer to facilitate the following LA design. The LA consists of five gain cells, an output buffer, and an offset cancellation circuit. The proposed optical receiver demonstrates $91dB{\Omega}$ transimpedance gain, 1.55 GHz bandwidth even with the large photodiode capacitance of 320 fF, 16 pA/sqrt(Hz) average noise current spectral density within the bandwidth (corresponding to the optical sensitivity of -21.6 dBm for $10^{-12}$ BER), and 40 mW power dissipation from a single 1.8-V supply. Test chips occupy the area of $1.35{\times}2.46mm^2$ including pads. The optically measured eye-diagrams confirms wide and clear eye-openings for 2.5-Gb/s operations.

• Journal of Radiation Protection and Research
• /
• v.21 no.2
• /
• pp.139-143
• /
• 1996

A multi-wire proportional counter with large sensitive area was designed and constructed considering diameter of anode wire. its material and space. A preamplifier connecting detector to main amplifier or counter was also designed and constructed for measurement output pulse from multi-wire proportional counter. The preamplifier was composed of charge-sensitive differential circuit. clipping circuit and amplification circuit. To test the performance of this equipment, terminal output pulse from the preamplifier was measured and compared with noise For these tests $^{239}Pu(360 Bq)\;and\; ^{90}Sr/^{90}Y(250 Bq)$ were used as radiation sources. The noise ingredient contributing to the maximum amplitude(180mV from $^{239}Pu$ and 200 mV from $^{90}Sr/^{90}Y$) was found to be very small(8 mV) Piled up pulse occurring at the output pulse of charge-sensitive differential circuit was measured as an independent pulse since this affected the amplification in the clipping circuit and amplification circuit. This information can be used to improve the loss of measurement due to piled up pulse.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.7
• /
• pp.944-950
• /
• 1993

Diodes and GaAs have been commonly used in a mixer design until recently. However, diodes are not preferred to use at the front-end of DBS receiver due to the conversion loss large noise. HEMT has larger conversion gain and better noise characteristics comparing with GaAs MESFET. This paper describes the design procedure, structure, and performance of a mixer, utilizaing HEMT designed by OKI Co. . A mixer configuration in which the local oscillator(LO) signal is applied to the gate is used. When the LO power is 0.01 dBm, the conversion gain of 3.7dB is obtained at IF and the 3 dB bandwidth is 400MMz.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.9
• /
• pp.13-20
• /
• 1999

A 2-stage MMIC(monolithic Microwave Integrated Circuits) LNA(Low Noise Amplifiers) at 30GHz hand has been designed and fabricated for the Ka-band Satellite Communications. The $0.15 {\mu}m$ with the width of $80 {\mu}m$ pHEMT technology was used for the fabrication of this MMIC LNA. Using the series feedback technique, ultra low noise and excellent S11 could be obtained at the same time without the cost of gain at 30GHz-band. The stability factors(Ks) for each stage and overall stage are greater than 1 at full frequency bands by the bias circuits and stabilization circuit. The measured performances, which agree well with the predicted performances, show this 2-stage MMIC LNA has the gain of more than 15.7dB and noise figure of less than 2.09dB over 29GHz to 33GHz.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.4
• /
• pp.59-64
• /
• 2020

Occasionally, MODEM test in satellite communication systems are needed. But Rx terminals in satellite communications are designed to obtain high SNR generally, therefore artificial bad conditions and environments are demanded for the test. One of the typical method is satellite output power reduction. Using noise generator can be another method. However, these costs a lot of money, time, and procedures in reality. In order to overcome these problems, this paper proposes an artificial noise generation method for MODEM test in satellite communication systems. First of all, SNR of a general heterodyne Rx terminal is calculated. Based on the calculation, a new model which is including variable attenuator is proposed to increase noise level. Simulation results illustrate the variable attenuator can control SNR, and these show that MODEM test in satellite communication systems be possible.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.199-207
• /
• 2011

A Ku-band low noise amplifier has been designed and fabricated by using 0.25 um SiGe BiCMOS process. The developed Ku-band LNA RFIC which has been designed with hetero-junction bipolar transistor(HBT) in the BiCMOS process have noise figure about 2.0 dB and linear gain over 19 dB in the frequency range from 9 GHz to 14 GHz. Optimization technique for p-tap value and electro-magnetic(EM) simulation technique had been used to overcome the inaccuracy in the PDK provided from the foundry service company and to supply the insufficient inductor library. The finally fabricated low noise amplifier of two fabrication runs has been implemented with the size of $0.65\;mm{\times}0.55\;mm$. The pure amplifier circuit layout with the reduced size of $0.4\;mm{\times}0.4\;mm$ without the input and output RF pads and DC bais pads has been incorporated as low noise amplication stages in the multi-function RFIC for the active phased array antenna of Ku-band satellite VSAT.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.81-89
• /
• 2020

This paper describes the design and fabrication of a LNB(Low Noise Block downd-converter) which is a component of a FST(Flyaway Satellite Terminal), one of the ET(Earth Terminal) of the military satellite. LNB is physically composed of an down-converter module, a low noise amplifier module, a transmit band suppression filter, a isolator, a housing, and a cable assembly. It was designed using simulator (AWR) to satisfy the electrical characteristics of LNB's such as gain, noise figure and unwanted signal. The gain and noise figure characteristics were measured at 61.4dBm and 1.37dB, respectively. The unwanted wave was measured at -66.79dBc. Of the electrical requirements of Table 1, not only the above three but also all other items were confirmed to be satisfied.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.137-140
• /
• 2008

본 논문에서는 높은 주파수에서 이미지신호에 따른 하향변환기의 선현성을 우수하게 나타내기 위하여 이미지 제거 특성이 우수한 능동소자를 선택하여 VSAT 위성통신용 Ka-band 하향변환기를 설계 및 제작하였다. 하향변환기의 구성은 저잡음 증폭기단, 이미지 제거 필터, 주파수 혼합기, 주파수 체배기, 전압제어 감쇄단 및 IF단으로 구성하였고, RF 경로의 동작 유무를 판단하기 위하여 국부 루프 경로로 구성되어 있다. 하향변환기의 이득은 $11.73{\sim}13.23dB$, 잡음지수 4.4dB 이하, 50dBc 이상의 이미지 제거 특성을 나타내어, 본 논문에서 제작한 하향변환기는 고속/광 대역폭을 가지는 디지털 통신 시스템에도 적용할 수 있다.

• Proceedings of the IEEK Conference
• /
• 2001.09a
• /
• pp.315-318
• /
• 2001

본 논문에서는 DTV 수상기에서 전송 받은 영상을 원하는 크기로 디스플레이 하기 위해 필요한 포맷 변환에 관한 알고리즘을 제시한다. 포맷 변환을 할 때에 영상을 보간하면 영상의 품질이 떨어지는 것을 볼 수 있는데 특히 에지 부분이 눈에 민감한 특성을 생각한다면 에지 부분에서의 무뎌짐은 상당한 문제점이 된다. 이를 해결하기 위해 고역 통과 필터링을 해주어 영상의 선명도를 올려줄 수 있는데 영상 전체에 고역 통과 필터링을 해주게 되면 영상의 에지뿐만 아니라 잡음 신호까지도 같이 증폭되는 문제점이 나타난다. 따라서 이를 해결하기 위해 에지 부분만을 적응적으로 고역 통과 필터에 통과시켜 잡음 성분은 줄이면서 에지 부분의 선명도는 올려주는 알고리즘을 제시하였다. 이를 검증하기 위해 다양한 영상에 대하여 컴퓨터 모의 실험을 하였고, 결과를 기존의 방법들과 비교하여 알고리즘의 우수성을 확인하였다.

• Journal of Welding and Joining
• /
• v.11 no.2
• /
• pp.1-12
• /
• 1993

용접과 관련되는 분야에서, 재료평가와 비파괴 검사법으로서의 Acoustic Emission의 응용을 살펴 보았다. 재료 평가법으로서의 AE는 다른 시험방법들이 검출해 내지 못하는 재료 내부에서의 미시적인 현상들을 정량적으로 평가할 수 있는 장점을 가지고 있다. 앞으로 새로운 용접재료의 개발이라든지, 고도의 신뢰성이 요구되는 용접부위의 정량적인 평가를 위해서 AE의 응용은 중요한 정보들을 제공하게 될 것이다. 한편 용접구조물의 비파괴적 평가법으로서의 AE는 균열의 동적인 거동 및 균열의 위치를 검지할 수 있다는 장점 때문에 응용범위는 더욱 넓어질 것이다. 여기서 유의하여야 할 점은, 목적으로 하는 AE신호를 수만배 까지 증폭시키는 과정에서 환경잡음의 영향을 무시할 수 없는 경우에는 우선적으로 잡음을 적극적으로 제거하는 고도의 연구도 함께 병행되어야 한다는 것이다.