• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.5
• /
• pp.417-423
• /
• 2017

This paper intend to implement monitoring systems for individual customized diagnostics to maintain ongoing disease management to promote human health. Analyze the threshold of a measured biological signal using a number of measuring sensors. Performance assessment revealed that the SVM algorithm for bio-signal analysis showed an average error rate of 2 %. The accuracy of the classification is 97.2%, and reduced the maximum of 19.2% of the storage space when you split the window into 5,000 pieces. Out of the total 5,000 bio-signals, 84 results showed that results from the system were differently the results of the expert's diagnosis and showed about 98 % accuracy. However, the results of the monitoring system did not occur when the results of the monitoring system were lower than that of experts. And About 98% accuracy was shown.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2003.04a
• /
• pp.35-35
• /
• 2003

)를 금속와이어에 인가하면 저항발열에 의해 와이어가 미세한 입자나 금속증기상태로 폭발하는 현상을 이용한 것으로 기상합성법에 속한다고 할 수 있다. 선폭법은 다른 제조법에 비해 공정이 간단하여 생산비용이 저렴하며, 원재료의 조성을 갖는 분말의 합성과 금속간화합물, 융점차이가 나는 재료의 합금화 등이 가능하다. 인가에너지의 크기와 폭발 시 분위기를 제어함으로써 분말의 평균크기와 분포 제어 또한 가능하다. 본 연구는 러시아의 우수한 기초기술을 바탕으로 Pb-Sn계 합금은 전기폭발법으로 극미세분말을 제조하였으며, 분말의 형상, 상 화학조성의 변화를 조사하였다. 본 실험에 사용된 Sn-Pb계(All-Union State Standard 1499-70, 0.53mm)합금와이어는 자동시스템(1-0.6Hz)에 의해 챔버안으로 공급되었다. 이 때 임계폭발 와이어 길이는 50-80nm으로 실험을 행하였다. 챔버 압력은 1.4~2.0atm으로 유지하였다. 제조된 분말의 특성은 XRD, XRPES, SEM등을 이용하여 분말의 형상과 상, 화학조성, 표면분석을 행하였으며 DSC, TGA, BET분석을 통하여 온도변화에 따른 금속분말의 열량변화, 질량변화, 비표면적을 측정하였다. 제조된 Sn-Pb계 분말은 모두 평균 입도 117nm~220nm의 구형형상이었다. 이때 합금분말의 조성은 51.17~63.21 at%Sn, 35.47~46.37 at%Pb로 나타났다. 와이어에 인가되는 비에너지(W/Wc)가 감소된에 EK라 표면층의 Pb함량이 증가함을 보였다. 이는 와이어 내부 저항의 감소로 인한 공정시간의 지연과 Sn, Pb의 확산계수 차이에 의한 것으로 사료된다. 열분석 결과, Sn~Pb계 화합물의 융점은 167~$169^{\circ}C$로 관찰되었으며, $10^{\circ}C$/min로 $920^{\circ}C$까지 승은 하였을 때 17.1~18 wt%의 질량증가를 보였다.TEX>계 나노복합분말이 얻어짐을 알 수 있었다. 이 때 X션 회절피크의 line broadening으로부터 복합분말의 Fe 명균 결정립 크기는 24nm로 초미세 결정럽의 분말합금이었다. 포화자화값은 볼밀처리에 따라 점점 증가하여 MA 30시간에는 20.3emu/g로 포화됨을 알 수 있었다. 또한 보자력 Hc는 MA초기단계에 350e로 매우 낮으나 30시간 후에는 Hc값이 2600e로 매우 큰 값을 나타내었다. 이것은 환원반응결과 초기에 생성된 Fe의 결정립이 비교적 크고 결정결함이 적으나 볼밀처리를 30시간까지 행하면 Fe 결정렵의 미세화 빛 strain 증가로 magnetic hardening이 일어나기 때문인 것으로 사료된다.길이가 50, 30cm인 압출재를 제조하였다. 열간압출한 후의 미세조직을 광학현미경으로 압출방향에 평행한 방향과 수직방향으로 관찰하였고, 열간 압출재 이방성을 검토하기 위하여 X선 회절분석을 실실하여 결정방위를 확인하였다. 전기 비저항 및 Seebeck 계수 측정을 위하여 각각 2$\times$2$\times$10$mm^3$ 그리고 5$\times$5$\times$10TEX>$mm^3$ 크기의 시편을 준비하였다.준비하였다.전류를 구성하는 주요 입자의 에너지 영역(75~l13keV)에서 가장 높은(0.80) 상관계수를 기록했다. 넷째, 회복기 중에 일어나는 입자들의 유입은 자기폭풍의 지속시간을 연장시키는 경향을 보이며 큰 자기폭풍일수록 현저했다. 주상에서 관측된 이러한 특성은 서브스톰 확장기 활동이 자기폭풍의 발달과 밀접한 관계가 있음을 시사한다.se that were all low in two aspects, named "the Nonsignificant group". And the issues were high risk perception in general setting and lo

• Journal of Korean Society of Steel Construction
• /
• v.10 no.1 s.34
• /
• pp.85-99
• /
• 1998

This paper describes an experimental study to examine collapse causes of the lifting cable due to brittle failure of an fitting anchor under the lifting works. Also, in this study an collapse mechanism that was obtained from stress analysis was compared with an actual collapse procedure. Fractographical analysis as well as chemical component test, tension test and Charpy V-Notch impact test for the fractured steel members were carried out. And then, its results were compared with that of normal steel members. Circumferential surface flaws were developed at internal facets of the fitting anchor before tensile stress occurred. Hence, a higher stress than nominal stress was occurred at flaws by stress concentration at the crack tip. Also, stress intensity factor of members increased by crack size of the potential flaws. Because the stress intensity factor at the crack tip was greater than critical values(fracture toughness), brittle fracture occurred under the lifting works. It is judged that the main collapse of the lifting cable is due to brittle fracture of the fitting anchor.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.4
• /
• pp.313-327
• /
• 2008

Thermo-mechanical coupled behavior of an underground structure during a fire accident have not been fully understood yet. Moreover, when such a thermo-mechanical coupled behavior is not considered in numerical analyses based on conventional heat transfer theory, fire-induced damage zone in an underground structure can be considerably underestimated. This study aims to develop a FEM-based numerical technique to simulate the thermo-mechanical coupled behavior of an underground structure in a fire accident. Especially, an element elimination model is newly proposed to simulate fire-induced structural loss together with a convective boundary condition. In the proposed model, an element where the maximum temperature calculated from heat transfer analysis is over a prescribed critical temperature is eliminated. Then, the proposed numerical technique is verified by comparing numerical results with experimental results from real fire model tests. From a series of parametric studies, the key parameters such as critical temperature, element size and temperature-dependent convection coefficients are optimized for the RABT and the RWS fire scenarios.

• Polymer(Korea)
• /
• v.28 no.2
• /
• pp.154-161
• /
• 2004

Modified poly(4-vinylpyridine) was obtained by partial quarternization of nitrogen atoms in pyridine rings of poly(4-vinylpyridine) with methyl group. By means of laser light scattering and fluorescence, it was found that this modified polymer chains were aggregated in the aqueous solution and its structure was core-shell type. The hydrophobic parts of the chains were densely condensed in core part and the hydrophilic part of quarternized amino with positive charge formed the shell part. In the mixed system of modified poly(4-vinylpyridine) and anionic surfactant, sodium dodecyl sulfate, it was observed that a critical aggregation concentration existed and that this critical concentration was suddenly decreased above 0.1 M NaCl. The size change of aggregates was also investigated by dynamic light scattering while sodium dodecyl sulfate was added into polymer solution upto the critical aggregation concentration.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.12
• /
• pp.87-94
• /
• 2008

This parer presents the soil ionization phenomena and parameters associated to characterize the transient performances of grounding system under lightning impulse Currents. Ionization properties in occurring some soil media were experimentally investigated. The cylindrical test cell was employed in order to facilitate the analysis of soil breakdown field intensity and ionized radius. The soil breakdown field intensity, dependence of impedance on the amplitude of impulse current, V-I curves and transient impedances were discussed based on the voltage and current oscillograms. It was found that the ionization process and dynamic behaviors were strongly dependent on the types of soil and two current peaks were not observed in highly water-saturated soils. The results presented in this paper will provide useful information on the improvement of transient performance of a grounding system subjected to lightning impulse Current considering the soil ionization.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.225-225
• /
• 2020

최근 국내·외에서는 재래식 소류사량 채집기를 이용한 직접계측방법의 한계를 보완하기 위해 음향센서(하이드로폰)를 활용하여 소류사가 이동할 때 발생하는 충돌음 신호로부터 소류사량을 간접적으로 추정하는 방법이 개발 검토되고 있다. 이러한 방법은 하이드로폰에 계측된 음향신호의 특성 중 음향 펄스 수와 소류사량의 상관성을 해명하는 연구가 주를 이루고 있다. 그러나 기존의 펄스 카운트 알고리즘은 원시신호에 대한 불충분한 노이즈 필터링 작업과 음향특성 중 진폭만을 고려하여 임계치를 설정하였기 때문에 운송되는 소류사량이 많을 경우 신호 파형의 중첩으로 인한 펄스 수의 과소평가, 감지 가능한 상한 입자 크기가 제한되는 등의 결점을 가지고 있다. 또한 대다수의 연구가 소류사량의 총량과 시계열적인 변화를 추정하는데 주안점을 두고 있어 소류사량의 입도분포를 추정하기 위한 연구사례는 매우 부족한 실정에 있다. 따라서 본 연구에서는 위와 같은 한계를 극복하기 위해 다양한 입경과 유속 조건을 고려한 단독입자 공급 실험을 통해 하이드로폰에서 계측되는 소류사 입경별 충돌음의 진폭과 특정 주파수대역을 기준으로 음향특성치를 효과적으로 필터링 할 수 있는 개선된 Band-Passs Method 방법을 제안하였다. 제안된 방법의 검증을 위해 기존의 음향신호 필터링 방법(증폭 채널 방법, 임계치 설정 방법)과 비교·분석을 수행한 결과 제안한 방법이 기존의 필터링 방법보다 높은 소류사량 추정률을 보이는 것으로 나타났다. 아울러 단일입경 연속공급 실험을 수행하여 입경별 소류사량 추정관계식을 산출하고 혼합입경의 입도분포 추정 가능성을 확인하였다. 연구수행의 최종단계로 혼합입경 소류사량 추정이 가능한 입경별 통합 소류사량 추정 알고리즘을 개발하고 실측 소류사량과의 비교·분석을 통해 알고리즘의 소류사량 추정 정밀도를 검증하였다.

• Journal of the Korean Vacuum Society
• /
• v.14 no.3
• /
• pp.153-158
• /
• 2005

The effective mean free path model was adopted to examine the thickness effect on the thermoelectric properties of flash-evaporated n-type $Bi_2Te_{2.4}Se_{0.6}$ thin films. Annealing effects on the electron concentration and mobility were also studied, and their variations were analyzed in conjunction with antisite defects. Seebeck coefficient and electrical resistivity versus inverse thickness showed a linear relationship, and the mean free path was found to be $5120\AA$ Electron mobility was increased by annealing treatment and electron concentration was decreased considerably due to reduction of antisite defects, so that electrical conductivity was decreased and Seebeck coefficient was increased. When annealed at 473k for 1 hour, Seebeck coefficient and electrical conductivity were $-200\;\mu V/k\;and\;510\omega^{-1}cm^{-1}$, respectively. Therefore, the thermoelectric power factor was improved to be $20\times10^{-4}\;W/(mK^2)$.

• Composites Research
• /
• v.15 no.4
• /
• pp.23-31
• /
• 2002

The two dimensional size effect of specimen gauge section ($length{\;}{\times}{\;}width$) was investigated on the compressive behavior of a T300/924 $\textrm{[}45/-45/0/90\textrm{]}_{3s}$, carbon fiber-epoxy laminate. A modified ICSTM compression test fixture was used together with an anti-buckling device to test 3mm thick specimens with a $30mm{\;}{\times}{\;}30mm,{\;}50mm{\;}{\times}{\;}50mm,{\;}70mm{\;}{\times}{\;}70mm{\;}and{\;}90mm{\;}{\times}{\;}90mm$ gauge length by width section. In all cases failure was sudden and occurred mainly within the gauge length. Post failure examination suggests that $0^{\circ}$ fiber microbuckling is the critical damage mechanism that causes final failure. This is the matrix dominated failure mode and its triggering depends very much on initial fiber waviness. It is suggested that manufacturing process and quality may play a significant role in determining the compressive strength. When the anti-buckling device was used on specimens, it was showed that the compressive strength with the device was slightly greater than that without the device due to surface friction between the specimen and the device by pretoque in bolts of the device. In the analysis result on influence of the anti-buckling device using the finite element method, it was found that the compressive strength with the anti-buckling device by loaded bolts was about 7% higher than actual compressive strength. Additionally, compressive tests on specimen with an open hole were performed. The local stress concentration arising from the hole dominates the strength of the laminate rather than the stresses in the bulk of the material. It is observed that the remote failure stress decreases with increasing hole size and specimen width but is generally well above the value one might predict from the elastic stress concentration factor. This suggests that the material is not ideally brittle and some stress relief occurs around the hole. X-ray radiography reveals that damage in the form of fiber microbuckling and delamination initiates at the edge of the hole at approximately 80% of the failure load and extends stably under increasing load before becoming unstable at a critical length of 2-3mm (depends on specimen geometry). This damage growth and failure are analysed by a linear cohesive zone model. Using the independently measured laminate parameters of unnotched compressive strength and in-plane fracture toughness the model predicts successfully the notched strength as a function of hole size and width.

• Journal of the Korean Magnetics Society
• /
• v.14 no.5
• /
• pp.169-173
• /
• 2004

We have synthesized monodispersed $\alpha$-F $e_2$ $O_3$ nano particles to investigate the spin change during the Morin transition temperature( $T_{M}$). The particle size was founded to have a very uniform distribution of 80 nm by x-ray diffraction and size dispersion analyzer. The Mossbauer spectra between the 4.2 K and the room temperature show that $T_{M}$ was shifted and the spin states of Fe ion were changed with the particle size. The Morin transition temperature of bulk usually quoted in literature is 265 K but, it decreases with the size and no transition was found at the critical size down to 4.2K. The spin direction of 80 nm sized particles are normal to the hexagonal c-axis above the $T_{M}$ and are tilted about 28～29$^{\circ}$ below $T_{M}$, which is the [110] direction of rombohedral structure.