• 대한소아치과학회지
• /
• 제38권4호
• /
• pp.376-382
• /
• 2011

제1대구치는 막중한 역할을 함에도 불구하고, 청소년 이전에 건강을 상실하는 경우가 드물지 않다. 본 연구는 청소년기 이전에 치수치료를 받게 된 제1대구치의 우식 및 수복 상태와 분포를 파악할 목적으로 시도되었다. 최근 5년간 부산대학교 치과병원에서 치수치료를 받은 18세 이하 106명 환자의 135개 제1대구치를 대상으로 의무기록에 대한 조사를 시행하여 다음과 같은 결과를 얻었다. 1. 평균 연령은 11.9세(남 11.5세, 여 12.5세)였고 유의한 성차를 보였으며(p<0.05), 악별로는 상악 47개, 하악 88개로 하악 치아가 더 많았다. 2. 치수 치료 전 치료 기왕력이 없는 치아는 74개, 치수 또는 수복 치료를 받은 치아는 61개였다. 그 중 재치수치료를 받게 된 경우는 22개로 치수절제술-치수절단술의 순이었으며, 단순 수복치료를 받았던 치아는 39개로 복합레진-아말감-GI-인레이-수복물 탈락 후 미치료-열구전색 및 주조 전장관의 순이었다. 3. 병소 위치가 분류 가능한 73개의 병소 중에서는 근심면 병소가 22개, 교합면 혹은 협설면 병소 39개, 원심면 병소가 12개를 차지하였다.

• 한국전자파학회논문지
• /
• 제25권1호
• /
• pp.83-91
• /
• 2014

현재 단품 단위 태깅(Item-level tagging)을 위한 UHF 대역 RFID Tag는 원거리 인식 거리와 저가 등의 장점들 때문에 유통산업 현장에서 폭발적으로 확대 보급되고 있다. 그러나 스마트폰과 태블릿 시장의 확대에 따라 실제 현장에서는 RFID 태그와 스마트 기기 간의 신호 간섭 문제가 예상된다. 이로 인해 RFID 태그는 인식률 및 인식 거리 감소 등 성능 저하가 발생하고 있다. 특히 KT에서는 최근 900 MHz 대역의 LTE 주파수와 구형 RFID 기술의 심각한 간섭 문제를 시연회를 통해 강조하였다. 이에 따라 본 논문에서는 스마트 기기로부터 송신되는 신호로 부터 수동형 UHF 대역 RFID 태그의 간섭 내성 측정 방법을 제안한다. 또한, 시중에 유통 중인 3개의 RFID 태그용 인레이(Inlay)를 선정하여 신호 간섭에 따른 인식 거리 감소 결과를 PCR 지수를 이용하여 정량적으로 비교 평가하였다. 그 결과, 신호 간섭 영향 측면에서 WCDMA 시스템에 비해 LTE 시스템이 약 3배 정도 강하며, 일부 태그의 인식 거리 성능은 약 60 % 저하되었다.

• Restorative Dentistry and Endodontics
• /
• 제25권1호
• /
• pp.17-40
• /
• 2000

Resin cements are used for cementing indirect esthetic restorations such as resin or porcelain inlays. Because of its limitations in curing of purely light cured resin cements due to attenuation of the curing light by intervening materials, dual cured resin cements are recommended for cementing restorations. The physical properties of resin cements are greatly influenced by the extent to which a resin cures and the degree of cure is an important factor in the success of the inlay. The purpose of this study was to evaluate the influence of porcelain thickness and exposure time on the polymerization of resin cements by measuring the microhardness and the degree of conversion, to investigate the nature of the correlation between two methods mentioned above, and to determine the exposure time needed to harden resin cements through various thickness of porcelain. The degree of resin cure was evaluated by the measurements of microhardness [Vickers Hardness Number(VHN)] and degree of conversion(DC), as determined by Fourier Transform Infrared Spectroscopy(FTIR) on one light cured composite resin [Z-100(Z)] and three dual cured resin cements [Duo cement(D), 3M Resin cement(R), and Dual cement(DA)] which were cured under porcelain discs thickness of 0mm, 1mm, 2mm, 3mm with light exposure time of 40sec, 80sec, 120sec, and regression analysis was performed to determine the correlation between VHN and DC. In addition, to determine the exposure time needed to harden resin cements under various thickness of porcelain discs, the changes of the intensity of light attenuated by 1mm, 2mm, and 3mm thickness of porcelain discs were measured using the curing radiometer. The results were obtained as follows ; 1. The values of microhardness and the degree of conversion of resin cements without intervening porcelain discs were 31~109VHN and 51~63%, respectively. In the microhardness Z was the highest, followed by R, D, DA. In the degree of conversion, D and DA was significantly greater than Z and R(p<0.05). 2. The microhardness and the degree of conversion of the resin cements decreased with increasing thickness of porcelain discs, and increased with increasing exposure time, D and R showed great variation with inlay thickness and exposure time, whereas, DA showed a little variation. 3. The intensity of light through 1mm, 2mm, and 3mm porcelain inlays decreased by 0.43, 0.25, and 0.14 times compared to direct illumination, and the respective needed exposure times are 53 sec, 70 sec, and 93 sec. In D and R, 40 sec of light irradiation through 2mm porcelain disc and 80 sec of light irradiation through 3mm porcelain disc were not enough to complete curing. 4. The microhardness and the degree of conversion of the resin cements showed a positive correlationship(R=0.791~0.965) in the order of R, D, Z, DA. As the thickness of porcelain discs increased, the decreasing pattern of microhardness was different from that of the degree of conversion, however.

• Restorative Dentistry and Endodontics
• /
• 제25권1호
• /
• pp.109-115
• /
• 2000

This study was designed to evaluate the microhardness of restorative composite resin and dual-cured composite resin cement which were light cured through the 1.5mm thickness composite overlay. For restorative materials, Z100 and Tetric Ceram were used. For dual cured composite cements, Variolink II((VL II) of three consistency (low, high, ultra high) were used. To determine the optimal microhardness of Z100, Tetric Ceram and Variolink II, each material was packed into the 1mm thickness teflon mold without composite overlay and light cured for 60 seconds. Then the microhardnesses of each sample were measured, averaged and regarded as optimal hardness of each material. To evaluate the microhardness of restorative composite resin and dual-cured composite resin cement which were light cured through the 1.5mm thickness composite overlay, the composites were packed into 1mm thickness teflon mold, coverd with celluloid strip, and then precured composite overlay which was made of Targis(Ivoclar/Vivadent, Liechtenstein) was positioned. 2 types of visible light curing machine, the power density of one of which was 400$mW/cm^2$ and the other was 900$mW/cm^2$, and one type of argon laser were used to cure the restorative composite and dual cured cement. For each group, 10 sample were assigned. The light curing tip was positioned over the composite overlay and light cured for 1min., 2min. or 3min with visible light curing machine or 15sec, 30 sec, 45sec, and 60 sec with argon laser. The Vickers hardnesses of upper and lower surface of Z100, Tetric Ceram, and 3 types of VL II cement were measured. When the 900 $mW/cm^2$ curing light was used, 2min. was needed for optimal curing of Z100 and Tetric Ceram. Variolink II did not be cured optimally even though the curing time was extended to 3min. When 400$mW/cm^2$ curing light was used, 3min. was necessary for Z100, whereas 3min. was not enough for Tetric Ceram. Variolink II was not cured optimally even though the curing time was extended to 3min. When argon laser was used, Z100, Tetric Ceram and Variolink II were not cured optimally in 60 seconds.

• Restorative Dentistry and Endodontics
• /
• 제33권5호
• /
• pp.443-451
• /
• 2008

이 연구의 목적은 단일 접착 과정의 레진 시멘트인 Maxcem을 제조사의 지시대로 사용하는 것과 부가적인 산 부식과정을 추가하여 접착을 시도함에 있어 그 임상적 접착 강도를 알아보고자 하는 것이었다. 치아 우식에 이환되지 않은 120개의 상하악 구치를 사용하여 간접 수복물 제작을 위한 와동을 형성하고 금인레이와 간접복합레진(Synfony) 수복물을 제작하였다. 실험군은 수복물의 종류마다 사용한 시멘트의 종류와 방식에 따라 세 군으로 분류하였다. 최종적으로 102개의 와동 시편에 수복물의 접착을 위해 Maxcem을 사용한 군, 인산으로 부가적인 산부식 후에 Maxcem을 사용한 군, 그리고 대조군으로 다단계 전-산부식 (total-etching) 시멘트인 Variolink II 를 사용하여 접착한 실험군으로 각 군 당 17개씩으로 분류하였다. 자체 제작한 만능시험기로 push-out 접착 강도를 측정하고 와동 접착 표면적으로 나누어 단위 면적당 결합력으로 산출하였다. SPSS 12.0K 프로그램을 사용하여 one-way ANOVA와 95% 신뢰도의 Scheffe's Test로 각 실험군의 접착력를 비교하였다. 이 실험의 조건하에서는 Maxcem을 사용할 때, 간접수복물의 종류에 관계없이, 제조사의 지시 외에 부가적인 산부식 과정은 접착 강도를 감소시키는 역효과를 유발하였으며 더욱 강한 접착력을 필요로 하는 경우는 다단계 접착제를 사용하여 산부식 과정과 접착제 적용, 시멘트 도포 등을 분리하여 사용하는 것이 바람직하다.

• Restorative Dentistry and Endodontics
• /
• 제21권2호
• /
• pp.619-627
• /
• 1996

There are increasing use of composite resin in the posterior teeth and the new indirect inlay technique was introduced for compensating much troubles faced in direct technique. Many researchers insisted that overall properties of restorative materials were enhanced by an additional curing but this technique still has a problems about using cement material. Resin inlay obtains retention force from friction and another adhesion to tooth structure. A shape of cavity preparation was noted but studies about cement thickness and bond strength with cavity divergency are rare. The purpose of this study is to assess the effect of cavity divergency on cement thickness and bond strength of resin inlay. Cavities, which divergency was $6^{\circ}$, $16^{\circ}$, and $26^{\circ}$ in each group, were prepared and their divergency was verified by Adobe Photoshop program through the image capture with stereo microscope and FlexCam. Inlays were fixed into the cavities with a resin cement, Superbond and were handled under chemical (in 75% ethanol for 24 hrs.) and thermal stress (500 cycles from $5^{\circ}$ to $55^{\circ}C$). MXT 70 (x400) was used for measuring the cement thickness and bond strength was evaluated with a universal testing machine. Following results were obtained : 1. The cement thickness in Mean (S.D.) were; 35.58 (10.31)${\mu}m$ in $6^{\circ}$ group, 35.97 (10.49)${\mu}m$ in $16^{\circ}$ group, and 41.43 (9.33)${\mu}m$ in $26^{\circ}$ group. But there was no significant difference between groups. 2. The bond strength in Mean (S.D.) were ; 33.18 (5.53)kg in $6^{\circ}$ group, 23.47 (13.40)kg in $16^{\circ}$ group, and 19.75 (10.48)kg in $26^{\circ}$ group. $6^{\circ}$ group showed significantly higher value compared to $16^{\circ}$ and $26^{\circ}$ groups (p<0.05). Although the results of this study indicate $6^{\circ}$ divergency will be good for resin inlay, cavity preparation with this type will have lots of difficulties in manufacturing, try-in, and cementation procedures, such as deformation. So it is concluded that $16^{\circ}$ divergent cavity preparation is recommended in resin inlay technique.

• 대한치과기공학회지
• /
• 제41권1호
• /
• pp.21-27
• /
• 2019

Purpose: To evaluate 2D and 3D of occulsal, mesial-occlusal and mesial-occlusal-distal cavity of composite resin inlay. Methods: Abutment tooth 16, 36 of FDI system was selected for the study. Inlay prostheses classified as occlusal cavity (OC group), mesial-occlusal (MOC) and mesial-occlusal-distal cavity (MODC) were prepared using composite resin. Composite resin was injected with composite resin in prepared tooth cavity and then photopolymerized with UV light. Additional thermal polymerization was performed. Marginal gap of composite resin inlays were measured by digital microscope(x160) with silicone replica technique. The data was analyzed from statistical software for Kruskal-Wallis test (${\alpha}=0.05$). 3-dimensional analysis was analyzed through superimposition method. Results: The smallest 2D marginal fit measure of the three groups was $47.0{\pm}21.6{\mu}m$ in the MOC group. The largest 2D marginal was $69.1{\pm}33.8{\mu}m$ in the MODC group. In the trueness of the three groups, the most accurate figure was $14.4{\pm}2.3{\mu}m$ for the MODC group. In Precision, the most accurate figure was $14.5{\pm}4.3{\mu}m$ for the MODC group. Conclusion : In this study, 2D marginal fit of OC, MOC, and MODC cavities fabricated with composite resin was applicable to all clinical applications. In the 3D inner surface accuracy evaluation, the MODC group showed the accuracy results.

• 대한치과보철학회지
• /
• 제53권1호
• /
• pp.19-25
• /
• 2015

오늘날 치과 분야에서 CAD/CAM (computer-aided design/computer-aided manufacturing)은 인레이나 크라운, 임플란트 등에 광범위하게 사용되고 있으며 총의치로도 그 영역을 넓히고 있다. CAD/CAM을 이용하여 총의치 제작 시 환자의 chair time과 방문 횟수를 줄일 수 있고 이로 인해 총 제작기간의 단축과 비용절감을 노릴 수 있으며 기공과정의 오차 감소를 기대할 수 있다. 최근 CAD/CAM을 이용한 여러 시스템 중 DENTCA$^{TM}$ CAD/CAM denture (DENTCA Inc. Los Angeles, USA)는 무치악 인상체를 스캔한 후 디지털 상에서 의치를 디자인한 뒤 3D 프린팅을 사용하여 시적의치를 제작해 이를 최종의치로 변환하는 기술을 이용하고 있다. 이로 인해 최적의 경우 2~3번의 내원으로 의치 장착이 가능하며 정확한 의치적합도를 기대할 수 있다. 본 증례의 환자는 71세 남자로, 기존 의치를 장기간 착용하여 재제작 상담을 위해 내원하였으며 예후가 불량한 잔존 치아와 치근을 발거하고 기존 하악의치를 수정하여 2달 간 사용한 뒤, 치료를 시작하였다. DENTCA에서 제공하는 알맞은 크기의 기성 트레이를 선택하여 one-step border molding을 시행한 후, wash impression을 채득하였다. 기존의치의 수직고경을 바탕으로 고딕 아치 트레이싱을 시행한 후 결정된 중심위로 상하악 트레이를 고정하고 교합인기를 시행하였다. DENTCA에서 이를 스캔하여 인공치 배열 및 festooning을 시행하고 3D 프린팅을 이용해 시적의치를 제작하였다. 환자 구강 내에 시적하고 교합평면 및 교합관계를 평가한 뒤 다시 교합인기를 시행하였으며, 이를 바탕으로 최종의치로 변환하였다. 양측성 균형교합을 형성하기 위해 안궁 이전을 이용하여 임상적 재부착 후 교합조정을 시행하였으며 이로 인해 양호한 결과를 얻었기에 보고하는 바이다.

• 대한소아치과학회지
• /
• 제29권4호
• /
• pp.632-640
• /
• 2002

초음파 진동을 치의학에 처음 이용한 것은 치석 제거기였으나, 최근에는 주조금속과 레진 인레이를 접착할 때, 인산아연시멘트나 레진시멘트의 점도를 낮추는데 이용되고 있다. 이러한 초음파 진동은 재료의 흐름성을 증가시킴으로써 피막도를 낮추고, 따라서 수복물 주위의 미제누출을 감소시킬 수 있는 장점이 있다. 그러나, 복합레진의 수복에 있어서 이러한 초음파 진동의 임상적 효과에 관한 연구가 아직까지 미흡한 실정이다. 이에 저자는 초음파 진동을 상아질 결합제에 적용하여 점도를 감소시킴으로써 상아세관으로의 레진 침투 정도의 변화와 결합력에 미치는 효과를 알아보고자 하였다. 발거 후 실온의 0.1% thymol 용액에 보관된 88개의 건전한 사람의 대구치를 치관부 법랑질을 제거하고 아크릴 레진을 이용하여 직경 1-inch의 PVC 관에 매몰하였다. 각 시편의 교합면이 아크릴봉과 동일한 높이가 되도록 220-, 500-grit의 연마지로 순차적으로 연마하였고, 무작위로 추출하여 각 군당 22개씩 네 군으로 분류하였다. 1군과 2군은 Single Bond(3M-ESPE, St. Paul, USA)를 3군과 4군은 One-Step(Bisco Inc., Schaumburg, USA)을 제조사의 지시에 따라 치면을 산부식, 수세, 건조한 후 연속하여 2번을 도포하였다. 2군과 4군은 초음파 치석제거기를 이용하여 치면에 대고 10 초간 진동을 가한 후 광중합하였다. 이후 직경 2.3mm, 높이 3.5mm의 Teflon mold(Ultradent Products Inc., South Jordan, USA)를 이용하여 복합레진을 충전한 후 40초씩 두 번에 나누어 광중합하였다. 모든 시편은 24시간 동안 실온의 수도물에 보관한 후 열순환을 시행하고, 만능측정기(Instron 4465, Canton, USA)로 전단결합강도를 측정하였으며 resin tag의 양상을 비교하기 위해 각 군의 시편의 치질을 탈회시킨 후에 표면을 주사전자 현미경으로 관찰하여 다음과 같은 결과를 얻었다. 1. 초음파 진동을 가하지 않은 1군, 3군에 비해 초음파 진동을 가한 2군과 4군에서 전단결합강도가 유의하게 높게 나타났다(p<0.05). 2. Single Bond와 One-Step의 전단결합강도는 유의한 차이를 보이지 않았다(p>0.05). 3. 전자현미경 관찰에서 초음파 진동을 가한 군에서 resin tag의 길이가 길었고, lateral branch의 수도 많이 관찰되었다.

• Restorative Dentistry and Endodontics
• /
• 제22권1호
• /
• pp.254-266
• /
• 1997

This study was to know the usefulness of argon laser for composite resin, to prove the polymerized effect of heat treatment of composite resin inlay and to get the curing method for optimal physical properties of composite resin inlay. In this study we used four light curing units and one heat curing unit: Visilux $II^{TM}$, a visible light gun: $SPECTRUM^{TM}$, an argon laser: Unilux AC$^{(R)}$ and Astorn XL$^{(R)}$, visible light curing unit: CRC-$100^{TM}$ for heat treatment. Compared to a control group, we divided the experemental groups into five as follows: Control group: Light curing(Visilux $II^{TM}$) Experimental group 1 : Light curing(Visilux $II^{TM}$) + Light curing(Unilux AC$^{(R)}$) Experimental group 2: Light curing(Visilux $II^{TM}$) + Light curing(Astron XL$^{(R)}$) + Heat treatment(CRC-$100^{TM}$) Experimental group 3 : Laser curing($SPECTRUM^{TM}$) Experimental group 4 : Laser curing($SPECTRUM^{TM}$) + Light curing(Unilux AC$^{(R)}$) Experimental group 5 : Laser curing($SPECTRUM^{TM}$) + Light curing(Astron XL$^{(R)}$) + Heat treatment (CRC-$100^{TM}$) According to the above classification, we made samples through the curing of Clearfil CR Inlay$^{(R)}$, which is a composite resin for inlay, in a separable cylindrical metal mold and polycarbonate plate. And then, we measured and compared the value of compressive strength, diametral tensile strength and the surface micro hardness of each sample. The results were as follows : 1. Among the experimental groups, group 5 showed the highest value of compressive strength, $157.50{\pm}10.24$ kgf and control group showed the lowest value of compressive strength, $103.93{\pm}21.93$ kgf. Control group showed significant difference with the experimental groups(p<0.001). Group 2 which was treated by the heat showed higher compressive strength than that of group 1 which was not, and there was significant difference between group 1 and group 2(p<0.001). Group 5 which was treated by heat showed higher compressive strength than group 4 which was not, and there was significant difference group 4 and group 5(p<0.001). 2. Among the experimental groups, group 5 showed the highest value of diametral tensile strength, $95.84{\pm}1.97$ kgf and control group showed the lowest value of diametral tensile strength, $81.80{\pm}2.17$ kgf. Control group which was cured by visible light showed higher diametral tensile strength than group 3 which was cured Argon Laser. Group 2 which was treated by heat showed higher compressive strength than that of group 1 which was not, and there was significant difference between group 1 and group 2(p<0.001). Group 5 which was treated by heat showed higher compressive strength than group 4 which was not, and there was a significant difference group 4 and group 5(p<0.001). 3. Among the experimental groups, group 5 showed the highest value of microhardness of top surface, $148.42{\pm}9.57$ kgf and control group showed the lowest value of microhardness, $111.43{\pm}7.63$ kgf. In the case of bottom surface, group 5 showed the highest value of $146.19{\pm}7.62$ kgf, and control group showed the lowest, $104.03{\pm}11.05$ kgf. Group 3 which was cured by Argon Laser showed higher diametral tensile strength than control group which was cured only with a visible light gun. Group 2 which was treated by heat showed higher compressive strength than that of group 1 which was not, and there was a significant difference between group 1 and group 2(p<0.001). Group 5 which was treated by heat showed higher compressive strength than group 4 which was not, and there was a significant difference group 4 and group 5(p<0.001). 4. According to the above results, we took a conclusion that argon laser can be used as a useful unit for curing the composite resin and heat treatment can improve the physical properties of the composite resin inlay.