• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1993.04a
• /
• pp.87-94
• /
• 1993

The study summarized in this paper is concerned with the buckling of a longitudinal bar in reinforced concrete members by numerical analysis method. The objectives of this study are to investigate the stress transfer mechanism between concrete and reinforcment and to propose a modeling equation. The result gives an acceptable agreement between the proposed modeling equation and the computer package as follows: (1) the proposed equation is a possible prediction of the strain softening of concrete and reinforcement buckling. (2) the buckling of longitudinal bars is mainly influenced by the spacing of hoops and the location of the bar.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.227-229
• /
• 2005

교류전동기의 벡터제어 구동 시스템에서 상전류 측정 오차는 토크 및 속도 제어 성능에 직접적인 영향을 주는 요소로서, 맥동 없는 토크 및 속도 제어를 위해서는 상전류의 정확한 측정이 필요하다. 상전류 측정 오차는 오프셋(Offset) 변동에 의한 오차와 스케일(Scale) 차이에 의한 오차로 분류할 수 있으며, 각각의 오차 성분은 고정자 전기 주파수의 1배 및 2배에 해당하는 토크 맥동을 야기 한다. 본 논문에서는 교류전동기 벡터제어 구동 시스템에서 상전류 측정 오차에 의한 토크 맥동을 저감시킬 수 있는 새로운 알고리즘을 제시하며, 시뮬레이션 및 실험을 통해 제안된 방식의 타당성을 입증한다.

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2017.11a
• /
• pp.129-130
• /
• 2017

본 논문에서는 국내 재난경보방송시스템의 현황을 소개하고 시스템 구성에 대해 알아본다. 운용의 목적이나, 사업의 진행방향 및 제조사 별 특성에 맞는 경보방송시스템들이 구성되어 운영되고 이다. 또한, 지진조기경보시스템의 구성을 알아보고 소개한다. 다양한 종류의 재난경보방송시스템이 목적에 따라 구축되어 운영되는데 상호 호환성의 문제를 지적하고 서로 다른 시스템들을 하나의 발령시스템으로 통합하기 위한 통합경보시스템 구성방안을 제안한다. 특히, 국가적 지진조기경보시스템에서 나타나는 한계점에 대해 알아보고 실효성을 향상하기 위해 MEMS 센서를 이용한 지진감지 및 경보방안을 제안한다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.9
• /
• pp.100-107
• /
• 2013

Since the West Sea experiences a big difference in tides, the output power of the small marine hydroelectric power plant varies with the tide. When an induction generator is used here for small hydroelectric power, the reactive power capacitor should be installed at the generator main bus to compensate for the changes in power. As such, the sizing method for the power compensation of the induction generator is reviewed and an optimal method for compensation is suggested. The self-excitation minimum capacitor capacity method, which prevents high voltages, and the power factor automatic control method, which retains a power factor of greater than 90% are reviewed. The compensation effect of reactive power is confirmed through a case study.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2493-2502
• /
• 2011

For Static analysis of software code, an experienced tester prefer detecting defects with using selective static technique. Many cases of static method have been reported such as coding rules, software metrics, defect data, etc. However, many of analysis case only present effectiveness of static analysis, not enough description for how the tester judged to classify code defects used in code analysis and removed them properly for ensure high quality. Occasionally, there are materials to show the effect of through some examples through some examples. But difficult to gain trust, because of not enough detail for application process. In this paper, introduced the static technique commonly used in railway and applied to the real development challenges. And the each of results were compared and analyzed. It is hard to generalize the results of this parer. But can be used and referenced as a case of study.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.388-391
• /
• 1999

Well oriented Bi2212 superconductor thick films were formed successfully on a copper substrate by liquid reaction between a Cu-free precursor and Cu tape method in which Cu-free BSCO powder mixture was' printed on copper plate and heat-treated. And we examined the effect of heat-treatment atmosphere for the superconducting properties and microstructure of Bi2212. The composition of Cu-free BSCO powder mixture was Bi$_2O_3$ : SrCO$_3$ : CaCO$_3$ = 1.2~2 : 1 : 1 and the heat-treatment for the superconducting formation reaction was performed in air, oxygen, nitrogen and low oxygen pressure. At heat-treatment temperature, the printing layer partially melt by reacting with CuO of the oxidizing copper plate, and the nonsuperconducting phases present in the melt are typically Bi-free phases and Cu-free phases. Among the nonsuperconducting phases, it is known that the (Sr,Ca)CuO$_3$ phase restrain the formation of the Bi2212 superconducting phase. Because a kind of the nonsuperconducting phases is controled by the oxygen partial pressure, the optimum condition in which the remnants of the second phases don't leave in the fully processed conductor was determined by XRD and the critical tempera to re (Tc) analysis.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.4
• /
• pp.199-208
• /
• 1993

Using several soil parameters which are obtained from the PI-experimental formulas and the back analysis method, the elastic analysis, the elasto-plastic analysis and the elasto-viscoplastic analysis for soil deformation are executed. Comparing the results with those of consolidation test, the indirect estimation method for soil parameters and the suitability of constitutive models are studied. The elastic analysis using back analysis result and the elasto-plastic analysis using the perconsolidation test. The elasto-viscoplastic analysis disagrees with the results of meability coefficient obtained from back analysis are the nearest to the results of the consolidation test. It is inferred that elasto-viscoplastic model is not adequate to the soil of which plasticity index is low.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.2223-2231
• /
• 2010

Recently, an important physical device of transportation, such as car, railroad, ship and aircraft has changed into electronic control unit. According to accident reports, the most of car accidents are caused by faults of embedded software loaded to computer control unit. The facts implies that the test to find defects in embedded software haven't performed sufficiently. As a result, it is necessary to establish the test procedures of embedded software based on safety assessment criteria. The objective of this proposal is to provide a unit test procedure complied with the safety assessment criteria for the embedded software. In addition, an effective unit testing procedure and defect analysis methods are proposed and a testing procedure using a safety criteria built-in tool is presented.

• Geotechnical Engineering
• /
• v.13 no.4
• /
• pp.109-120
• /
• 1997

In the working stress conditions, the strain level in a soil mass experienced by existing structures and during construction is less than about 0.1-1%. In order to analyse the deformational behavior accurately, the in-situ testing technique which provides the reliable deformational characteristics at small strains, needs to be developed. The purpose of this paper is to measure the small-strain shear modulus of soils by using pressuremeter test(PMT). PMT is a unique method for assessing directly the in-situ shear modulus of soils with strain amplitude. For the accurate small strain measurements without initial disturbance effect, the unloading-reloading cycle was used and the measured modulus was corrected in view of the relevant stress and strain levels around the PMT probe during testing. Not only in the calibration chamber but in the field, PMT tests were performed on the cohesionless soils. The variation in shear modulus with strain amplitude ranging from 10-2% to 0.5% was reliably determined by PMT PMT results were also compared with other in-situ and laboratory test results. Moduli obtained from different testing techniques matched very well if the effect of strain amplitude was considered in the com pall son.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.82-89
• /
• 2007

This paper presents a coplanar waveguide fed L-planar type monopole antenna which covers ultra wideband(UWB) region of 3.1 GHz to 10.6 GHz. The proposed UWB L-planar type monopole antenna is designed and implemented on the organic substrates( ${\varepsilon}_{r}=3.38,\;@10\;GHz$). The radiation elements, feed line, and ground planes of the antenna are printed on the same conductive layer of the substrates. The bandwidth of the proposed antenna is measured in the range of 3.0 GHz to 11.0 GHz. The measured radiation patterns are symmetrical in E-plane and omni-directional in H-plane. Antenna gains ranges from 1.4 dBi to 4.6 dBi. The proposed UWB antenna shows that the structure is adequate for the design of RFIC.