• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.1
• /
• pp.21-28
• /
• 2008

Stress-strain curves based on Ramberg-Osgood and Hollomon relations are strongly dependent upon the regressed range of strain. This work investigates mathematical expressions of true stress-strain curves of metallic materials. We first observe the variation of yield strength, strain hardening exponent and stress-strain curve with regressed range of stain. Based on sectional regression and expression using one or two parameters, we propose an optimal strain range for which yield strength and nonlinear material behavior are quite appropriate.

• The Korean Journal of Rheology
• /
• v.9 no.4
• /
• pp.174-182
• /
• 1997

결정성 고분자수지는 가공조건에 의해 결정되는 미세구조의 변화에 따라 최종물성 이 현저히 달라지므로 최종 성형품의 물성을 극대화하기 위해서는 성형가공 중에 필연적으 로 부가되는 열이력 뿐만 아니라 전단이력이 결정화 거동에 미치는 영향을 규명하고 가공조 건의 최적화를 통하여 미세구조를 적절히 제어하는 것이 요구된다. 따라서 본 연구에서 in-situ 상태로 전단유도 결정화거동을 조사할수 있는 rheo-kinetic 실험 방법을 개발하고 결정화 거동에 미치는 열이력과 전단이력의 영향을 규명하고자 하였다. 이를 위해 비교적 결정화 속도가 빠른 폴리 부틸렌 테레프탈레이트 수지를 대상으로 냉각조건, 전단부가시간, 전단속도등을 다양하게 변화시키면서 plate-plate 레오미터로 시간에 따른 전단응력의 변화 를 조사하는 rheo-kinetic 연구를 수행하였다. 아울러 실험 중에 액체 질소로 급냉하여 얻은 시료를 대상으로 등온 및 비등온의 열분석 실험을 수행하고 JMA식과 Hoffman-Lauritzentlr 을 사용하여 분석한 다음, 그 결과를 rheo-kinetic 해석결과와 비교함으로써 결정화 거동에 미치는 전단응력의 영향을 규명하였다. 일정전단속동하에서 수행한 rheo-kinetic 실험결과, 시간에 따른 저난응력의 증가와 용융열이 증가하는 경향이 매우 유사한 거동을 보이므로 전 단응력의 증가는 결정화가 일어남에 기인한 결과임을 확인할수 있었으며 고분자수지가 전단 이력을 받게 되면 분자배향의 결과로 결정화 유도시간이 짧아지고 결정화속도가 증가할 뿐 만 아니라 보다 더 높은 온도에서 결정화가 일어나게 됨을 알수 있었다. 또 결정화 반가기 시간과 Hoffman-Lauritzen 식의 매개변수들이 전단속도, 전단부가시간, 결정화 온도 등의 이력에 무관하게 전단응력에 따라 선형적으로 변하고 있으므로 전단유도 결정화거동은 수지 에 부가되는 전단응력에 직접적인 영향을 받음을 알수 있었다. 이상과같은 전단유도 결정화 거동에 관한 결과를 가공공정상의 열전달 현상과 결합하여 해서하면 성형품 내부의모폴로지 의 예측이 가능하므로 성형품 물성의 극대화 방안의 수립에 이용될수 있을것으로 사료된다.

• Geotechnical Engineering
• /
• v.6 no.3
• /
• pp.65-76
• /
• 1990

A series of consolidated drained and untrained cubical triaxial tests were performed to investigate three dimensional strength characteristics of compressible sand. All specimens, which are formed by deposisting a fine sand loosely, were used. Failure strength in terms of effective stress analysis was greatly influenced by the variation of intermediate principal stress and so was failure criterion The adjusted effective frictional angles obtained by the stress state projected on the same octahedral plane showed almost same value, while the measured effective frictional angles showed considerable difference depending on the drainage conditions. Results of total stress analysis in undrained test turned out to fit Tresca's failure criterion well, but results of effective stress analysis turned out to fit Lade's failure criterion well.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.341-346
• /
• 2010

The effect of specimen geometry on the bending and tensile strengths of dissimilar joints ($\beta-Si_3N_4/S45C$) with copper interlayers was evaluated. The average bending strength of specimens with circular cross sections was higher than that of specimens with rectangular cross sections. The crack initiation stress ($\sigma_i$) was successfully determined by the acoustic emission (AE) method and was approximately 60~80% of the bending strength. The residual stresses near the interfaces on the ceramic side were measured by X-ray diffraction before conducting the bending test. The bending strength and the crack initiation stress decreased with an increase in the residual stresses. The effect of the bending strain component was evaluated by the tensile testing; the tensile strength decreased with an increase in the bending strain component and was approximately 80% of the bending strength.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.3 s.36
• /
• pp.407-421
• /
• 1998

The purpose of this paper is to provide and verify an analytical method, based on the spline finite strip method, which can be used to investigate the buckling mode and stress of thin-walled steel sections. Geometric imperfection and initial stress of plates and plate assemblies, which are resulted from various preloadings and may cause prebuckling deformations before buckling, are included in the analysis. Material nonlinearity and residual stress are also considered. It can be applied to sections with simple or non-simple boundary conditions and arbitrary loading. The method has been applied to investigate the buckling behavior of plates and plate assemblies which are subjected to compression with initial imperfections and residual stresses.

• Journal of the Korean Geosynthetics Society
• /
• v.5 no.3
• /
• pp.31-36
• /
• 2006

In this study, stress relaxation behaviors of nonwoven geotextile and geomembrane which have protection, filtration and drainage, water barrier functions, respectively were examined. 'Theory of transition phenomen' was applied to interpretate the stress relaxation behaviors of two geosynthetics. The initial and later relaxation times for stress relaxation behaviors of geosynthetics were derived from the constitutive equations. The initial relaxation behaviors of these geosynthetics were dependent on the additional strains and were especially faster with temperature. Finally, both relaxation times of geosynthetics were shorter with additional strain and temperature and the reduction of relaxation times of nonwoven geotextile were larger than those of geomembrane.

• The Journal of Engineering Geology
• /
• v.4 no.2
• /
• pp.231-243
• /
• 1994

To better understand the fundamental problems of the true micro-damage in medium-grained granite under uniaxial compressive stress, micro-damage localization, initiation and propagation have been observed in a great detail in contact portion of two grains such as quartz and feldspar. For this purpose, new experimental system allowing us to observe the micro-damaging process continuously was developed. Earlier studies used the specimens of unloaded state and it is difficult to visualize stress-induced microcracks under unloading state. Thus, direct observation under loading state is very important for understanding the true micro-damage process. The results explain well the mechanism of micro-damage at two grains, and mechanics of the micro-damage is clarified well by Hertzian fracture mechanics.

• Journal of the Korean Geosynthetics Society
• /
• v.3 no.4
• /
• pp.21-27
• /
• 2004

Stress relaxation behaviors of nonwoven geotextile and geomembrane which have protection, filtration and drainage, water barrier functions, respectively were analyzed. 'Theory of transition phenomena' was applied to interpretate the stress relaxation behaviors of two geosynthetics. The initial and later relaxation times for stress relaxation behaviors of geosynthetics were derived from the constitutive equations. The initial relaxation behaviors of these geosynthetics were dependent on the additional strains and were especially faster with temperature. Finally, both relaxation times of geosynthetics were shorter with additional strain and temperature.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.169-169
• /
• 2010

박막형 CIGS 태양전지의 배면전극으로 사용되는 Mo 박막은 낮은 저항으로 인한 전기전도성과 열적 안전성이 아주 우수하다. 연구에서는 연성 CIGS 태양전지의 제조를 위한 Mo 배면전극의 대면적 증착기술에 관한 것으로 DC Magnetron Sputtering 공정을 이용하여 전주기술을 통한 Ni-Fe계 연성기판재 위에 졸걸법으로 합성된 $SiO_2$ 절연박막에 Mo 박막을 증착하는 것을 목적으로 하고 있다. 실험에서는 연성기판재 대신 시편을 Sodalime glass, Si wafer, SUS계 소재를 사용하여 스퍼터링 공정에 의한 Mo 박막을 증착하였다. 실험에서 타겟에 인가되는 전력과 공정압력을 변수로 하여 Mo 박막의 증착율, 전기저항성을 측정하였다. 타겟의 크기는 $80mm{\times}350mm$, 타겟과 기판간 거리 20cm 이었으며, 공정 압력은 2~50 mtorr 영역에서 인가전력을 0.5-1.5kW로 하였다. Mo 박막의 증착율과 전기적 특성을 측정하기 위하여 $\alpha$-step과 4-point probe(CMT-SR 1000N)를 이용하였다. 그리고 Mo 박막의 잔류응력을 측정하기 위하여 잔류응력측정기를 이용하였다. Mo 박막의 미세구조분석을 위하여 SEM 및 XRD를 분석을 실시하였다. 배면전극으로서 전기저항성은 공정압력에 따라 좌우 되었으며, 2 mTorr 공정압력과 1.5kW의 전력에서 최소값인 $8.2\;{\mu}{\Omega}-cm$의 저항값과 증착율 약 $6\;{\mu}/h$를 보였다. 기판재와의 밀착성과 관련한 잔류응력 측정과 XRD분석을 통한 결정립 크기를 분석하여 공정압력에 따른 Mo 박막의 잔류응력과 전기 저항 및 결정립 크기의 상관관계를 조사하였다. 그리고 대면적 CIGS 증착공정을 위해 직각형 타겟을 통해 증착된 Mo 박막의 증착분포를 20cm 이내 조사하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5A
• /
• pp.817-822
• /
• 2006

Post-tensioning the full-depth precast slab longitudinally is to eliminate the tensile stresses in the transverse joints and to prevent any leakage through the joints. When the prestressing is applied to full-depth precast slab which does not composite steel girder, stress concentration occurs at the corners of shear pocket, and compressive stress is not uniformly distributed in the section of precast slab. In this paper, full-depth precast slabs using four different shapes of shear pockets are analyzed by commercial finite element program. Round type of shear pockets is superior to reduction in stress concentration.