• Journal of Energy Engineering
• /
• v.10 no.2
• /
• pp.120-131
• /
• 2001

최근 세라믹 필터에 대한 연구는 열악한 환경 및 산성가스에 대한 저항성으로 인해 고온 가스 여과에서 가장 전망 있는 기술로 부각되는 시점에 있다. 본 연구의 목적은 탄화규소(SiC) 세라믹 캔들 필터를 사용하여 IGCC와 PFBC의 새로운 전력생산 공정에서 배출되는 먼지를 제거하기 위한 필터성능을 조사하기 위함이다. 필터의 성능 평가는 고온.고압.고온.상압 조건에서 이루어졌으며 필터의 압력강하, 먼지 제거효율, 저항 계수, 그리고 열적.기계적 저항성 등을 파악하였다. 길이 30cm, 60cm 필터에 2종류의 먼지(코크스와 물유리 공정)를 이용하여 나타난 먼지 제거효율은 99.9% 이상을 보였으며 필터의 평균 기공 크기가 감소함에 따라 압력강하가 증가함을 확인하였다. 또한 탄화규소 세라믹 필터의 성능은 내부압력이 증가할수록 압력강하가 감소하고 유량이 증가할수록 압력강하가 증가함과 특히 유체에 대한 압력강하 변화는 온도의 영향보다는 상대적으로 내부압력에 더 많은 영향을 받음을 확인하였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.2
• /
• pp.88-94
• /
• 2013

The primary objective of the current work is to obviously analyze regarding effects of trim conditions of a ship on resistance performance using model test and CFD. Model tests at a towing tank are conducted to investigate resistance for trim conditions at the given same displacement. Measured resistance shows small but distinct differences according to trim conditions. However, these differences are difficult to be clarified by measured physical quantities and wave pattern analysis from model tests. CFD is employed for the assessment of resistance performance according to trim conditions. The flow computation is conducted considering free surface and dynamic trim using a commercial CFD code (STAR-CCM+). The initiative of the present work is to systematically demonstrate pressure resistance acting on each region of divided finite zones of ship surface along the length and draught direction of surface when pressure distribution on the ship is interpreted. Also, a standard to assess the pressure resistance applied on the divided regions of a ship is established.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.2
• /
• pp.66-72
• /
• 1992

A computational method of the Michell integral for water of finite depth is developed and the method makes use of the expansion of the hull form by the Legendre polynomial in both the longitudinal and the vertical directions. The wave resistance coefficient is given as a quadruple summation of the product of the shape factor and the hydrodynamic factor. The shape factor depends only upon the geometry of the hull form, and the hydrodynamic factor upon the depth-based Froude number and the ratios of the water depth and the draft to the ship length. Example calculations are done for the Wigley parabolic hull and the Series 60 $C_B$ 0.6, and the comparison of our results with the existing experimental data is shown.

• Journal of the Society of Naval Architects of Korea
• /
• v.59 no.6
• /
• pp.345-354
• /
• 2022

It is easy for a ship passing through confined waters to be exposed in dangers of collisions and grounding due to different hydrodynamic responses. Since marine accidents can cause significant impacts on environments, global economy, and human lives, it is necessary to study the effect of shallow water on hydrodynamic performance of a ship. In this paper, the effect of water depth on resistance performance was investigated using CFD analysis as an initial study for improving navigational safety of a large container ship under confined waters. After a CFD set-up for deep water condition was validated and verified by comparing CFD analysis with model test results, CFD calculations according to ship speed and water depth were conducted. The features were investigated in terms of tendency and physical knowledge related to resistance performance. The increase of resistance due to shallow water effect was reviewed with empirical formula suggested from SWABE JIP. Speed loss due to shallow water effect was additionally reviewed from estimated delivered power according to ship speed and water depth.

• Journal of computational fluids engineering
• /
• v.15 no.4
• /
• pp.1-8
• /
• 2010

This article describes the numerical investigation of turbulent blood flow in the stenosed artery bifurcation under periodic acceleration of the human body. Numerical analyses for turbulent blood flow were performed with different magnitude of periodic accelerations using a modified turbulence model which was considering drag reduction of non-Newtonian fluid. The blood was considered to be a non-Newtonian fluid which was based on the power-law viscosity. In order to validate the modified $k-{\varepsilon}$ model, numerical simulations were compared with the standard $k-{\varepsilon}$ model and the Malin's low Reynolds number turbulence model for power-law fluid. As results, the modified $k-{\varepsilon}$ model represents intermediate characteristics between laminar and standard $k-{\varepsilon}$ model, and the modified $k-{\varepsilon}$ model showed good agreements with Malin's verified power law model. Moreover, the computing time and computer resource of the modified $k-{\varepsilon}$ model were reduced about one third than low Reynolds number model including Malin's model.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.1
• /
• pp.23-33
• /
• 2019

Unmanned Surface Vehicle (USV) is being developed to do maritime survey and maritime surveillance at Korea Research Institute of Ships & Ocean engineering (KRISO). The goal is that USV should be operated at the maximum speed of 45 knots and it should be operated at sea state 4. Therefore the planing hull of USV should be excellent in resistance performance and manoeuvring performance. It is needed to check its performance using Experimental Fluid Dynamics (EFD), Computational Fluid Dynamics (CFD) or analytic method before designing the hull. In this study, resistance performance was analyzed by EFD and CFD. EFD with heave and pitch was performed at high speed towing system in Seoul National University. CFD was performed using SNUFOAM based on openFOAM with dynamic mesh to calculate running attitudes. The results of CFD were compared with EFD results. The results of CFD were resistance, running attitudes and wave height. The flow distribution and pressure distribution were also analyzed. The results of numerical resistance was under estimated than EFD. Even though the results of CFD have a slight limitation, it can be successfully used to estimate the resistance performance of planing hull. In addition it can be used as a supplement for EFD results.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.2
• /
• pp.267-274
• /
• 2018

A variety of appendages are attached to coastal and offshore fishing boats to improve stability during navigation or fishing operations (stability performance and roll reduction). These appendages are generally classified into three types, which are shown in Fig. 1. The numerical calculations were conducted for the following eight cases: one case of a bare hull, three cases where a single appendage attached, three cases of a pair of appendages attached, and one case where all three appendages were attached. Table 1 presents the main dimensions of the bare hull and Table 2 describes the main dimensions of the three appendages. The fluid dynamic performance with regard to the three hull appendages was evaluated via CFD for the following cases: each of the appendages attached independently, a pair of appendages attached, and all three appendages attached simultaneously. The No. 1 appendage showed that pressure resistance was proportionally greater than friction resistances. Both Nos. 2 and 3 appendages showed comparable levels of pressure and friction resistances. The correlation between appendages was minimal in the case of pairs and Comparing the cases of the No. 2 appendage attached and all appendages attached, at 11 kn, the EHP showed an difference of 9 %.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.6
• /
• pp.688-696
• /
• 2023

In the present study, free roll decay and resistance performances of fishing vessels were evaluated with the combinations and variations of in the parameters of appendages which are attached to improve motion performance of fishing vessels. Computational Ffluid Ddynamics was used to perform free roll decay and resistance analysis. The roll period and decay coefficient were derived by the variations in the combination and dimensions of the primary appendages of the bilge keel and the under keel. It was observed thatThe variations of in the length of the under keel did not significantly impact to the roll damping coefficient. Conversely, for the bilge keel, an increase in the length and angle resulted in an increase in the roll damping coefficient. Comparison of resistance performance was additionally assessed among the selected hulls with the appendages and bare hull. The resistance of the hull with the appendages was higher than that of the bare hull due owing to the changes of in the pressure on the surface of the hull and trim angle. Throughout the present study, the impact of appendage parameter and arrangement on the free roll decay and resistance performance of fishing vessels were was assessed,. which This will be beneficial for the application of appendages to fishing vessels.

• Journal of Energy Engineering
• /
• v.19 no.3
• /
• pp.143-150
• /
• 2010

Line source method of borehole system assumes the entire surrounding medium is uniform. However, thermal properties of grouting region are considerably different from those of surrounding soil. In this study we investigate the effect of grouting materials on the solution of line source method with the aid of numerical analysis. This numerical model generates the temperature of borehole fluid with which line source solution can be obtained. Then this solution can be compared with input condition of numerical model. The results of this comparison show that thermal conductivity and borehole thermal resistance of line source solution are approximately 86% and 91% of the input condition of numerical model. Chart method is developed in this study to find the numerical input conditions (thermal conductivity and borehole thermal resistance) from the line source solution. Thermal response test of test borehole is conducted, the results of which are approximately consistent with the Chart method. Thermal property changes of grouting materials on the line source solution are also examined.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.20 no.5
• /
• pp.552-557
• /
• 2014

The objective of the This study is to access the speed performance employing the sea trial test and CFD with the our own designed and manufactured one-man boat. The overall design process including hull form design was explained. The sea trial was carried out with a manufactured boat in the clam sea. Brake power at the design speed of a boat through the sea trial was measured as 1680 W. The flow computation was conducted considering free surface and dynamic trim using a commercial CFD code(STAR-CCM+). The result of computation provided the information that residual resistance is bigger than fraction's at design speed. The total efficiency were predicted based on the sea trial and CFD. The Total efficiency was divided into shaft efficiency and quasi-propulsive efficiency. By using quasi-propulsive efficiency, it becomes possible to predict speed performance of boat in future. The results can provide information regarding hull form design, performance analysis and development of a boat in future.