• 제목/요약/키워드: 유연 벽면

검색결과 19건 처리시간 0.024초

유연재 코팅 평판의 난류 변동압력 특성에 관한 실험적 연구 (Experimental Study on the Characteristics of Turbulent Wall Pressure Fluctuation Over Compliant Coatings)

  • 박경훈;이승재;신구균
    • 한국음향학회지
    • /
    • 제26권6호
    • /
    • pp.293-300
    • /
    • 2007
  • 수중운동체가 주행할 때 수중운동체의 표면에는 난류 경계층이 형성되고, 난류 경계층 내 벽면 변동압력은 탄성체인 수중운동체의 표면을 가진시켜 유동 유기 소음을 발생시킨다. 이러한 유체 소음을 감소시키기 위한 하나의 방법으로 수중운동체 표면에 유연재를 부착하여 수중운동체의 유동 유기 방사 소음을 감소시키는 방법이 제안되기도 한다. 본 논문에서는 유연재 부착에 따른 수중에서의 유체소음의 변화 특성을 살펴보기 위하여 유연재가 코팅되지 않은 강판 시편과, 고무 재질의 Neoprene 및 폴리우레탄 재질의 유연재가 부착된 강판시편을 저소음 공동수조에 설치한 후 여러 가지 유속 조건에서 유체소음의 주요 소음원인 난류 경계층 내 벽면 변동압력을 측정하고 그 결과를 비교 분석하였다. 그 결과 유연재를 코팅한 경우에는 유연재로 인하여 난류 경계층의 두께가 두꺼워지는 등 경계층 유동이 변화하지만, 유연재에서의 난류 에너지의 소산으로 인하여 고주파수 대역에서 약 10dB의 벽면 변동압력의 감소 효과를 확인할 수 있었다.

벽면의 유연성을 고려한 액체저장탱크의 동적해석 (Seismic Analysis of Liquid Storage Tanks Considering Shell Flexibility)

  • 이창근;윤정방
    • 대한토목학회논문집
    • /
    • 제7권4호
    • /
    • pp.21-29
    • /
    • 1987
  • 직립원통형 액체저장탱크가 지진하중을 받을 때, 벽면 유연성이 벽면에 작용하는 유동압력에 미치는 영향에 대해 연구하였다. 탱크 구조물은 환(ring)형 유한요소를 사용하여 이상화하였으며, 유동에 대한 해는 Laplace 방정식을 이용하여 구하였다. 쉘-유체계의 운동방정식은 자유표면거동과 벽면유연성의 상관효과까지 포함하여 구성하였으며, 이에 따른 쉘 거동과 자유표면거동에 대한 자유진동모우드를 해석하는 방법이 개발되었다. 예제해석으로는, 구조적 특성이 다른 몇개의 저장탱크에 대해, 응답스펙트럼 해석법과 시간영역 해석법을 사용하여 동적응답을 구하였고, 그 결과들을 비교 분석하였다.

  • PDF

유량과 벽면횡단압력의 변화에 의한 유연한 관의 압착현상 (Collapsible Phenomena in the Flexible Tubes due to the Flow Rate and Transmural Pressure Changes)

  • 조민태;서상호;유상신
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2000년도 추계학술대회논문집B
    • /
    • pp.377-380
    • /
    • 2000
  • The collapsible phenomena of the circular tubes due to the excessive transmural pressure are investigated experimentally. Collapsible tubes are installed in the test section where the external pressure is applied to the test tubes by applying the hydrostatic head. The collapsible circular tubes are made of rubber, whose diameters are 6 and 4.2 mm, respectively. The hydrostatic water head of the upper reservoir is applied to the test section. Pressures at the upstream and downstream sides are measured by the pressure transducers. The collapsible phenomena are observed as the transmural pressure Increases, and also the flutter phenomenon occurs due to the critical transmural pressure.

  • PDF

난류 경계층에서 컴플라이언트 코팅된 벽면과 점탄성 벽면의 방사 소음에 관한 실험적 연구 (Radiated Sound from Compliant and Viscoelastic Plates in a Turbulent Boundary Layer)

  • 이창준;이승배;권오섭;전우평
    • 대한기계학회논문집B
    • /
    • 제27권3호
    • /
    • pp.294-301
    • /
    • 2003
  • We examine a problem in which porous/viscoelastic compliant thin plates are subject to pressure fluctuations under transitional or turbulent boundary layer. Measurements are presented of the frequency spectra of the near-field pressure and radiated sound by compliant surface. A porous plate consisting of 5mm thick. open-cell foam with fabric covering and a viscoelastic-painted plate of 1mm thick over an acoustic board of 4mm thick were placed over a rigid surface in an anechoic wind tunnel. Streamwise velocity and wall pressure measurements were shown to highly attenuate the convective wall pressure energy when the convective wavenumber (k$_{c}$h) was 3.0 or more. The sound source localization on the compliant walls is applied to the measurement of radiated sound by using an acoustic mirror system.

유연벽면 점탄성 소재 배합비와 저항저감 효과의 상관관계 (Correlation Between the Composition of Compliant Coating Material and Drag Reduction Efficiency)

  • 이인원;안남현
    • 대한기계학회논문집B
    • /
    • 제33권6호
    • /
    • pp.389-395
    • /
    • 2009
  • A specially designed flat plate was mounted vertically over the axial line in the wind tunnel of the Pusan National University. Strain balances were mounted in the trailing part of the plate to measure the skin friction drag over removable insertions of $0.55{\times}0.25m^2$ size. A set of the insertions was designed and manufactured: 3 mm thick polished metal surface and three compliant surfaces. The compliant surfaces were manufactured of a silicone rubber Silastic$^{(R)}$ S2 (Dow Corning company). To modify the viscoelastic properties of the rubber, its composition was varied: 90% rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% + 15% (strong). Modulus of elasticity and the loss factor were measured accurately for these materials in the frequency range from 40 Hz to 3 kHz. The aging of the materials (variation of their properties) for the period of one year was documented as well. Along with the drag measurement using the strain balance, velocity and pressure were measured for different coating. The strong compliant coating achieved 5% drag reduction within a velocity range $20{\sim}40$ m/s while standard and weak coatings increased drag reduction.

유연벽면 점탄성 소재의 광대역 동특성 계측 기법 (Measurement Method of Broadband Dynamic Characteristics of Viscoelastic Material for Compliant Coating)

  • 바셀 서우디;안드레이 보이코;전호환;이인원
    • 대한조선학회논문집
    • /
    • 제45권1호
    • /
    • pp.73-80
    • /
    • 2008
  • An improved method to measure the dynamic viscoelastic properties of elastomers is proposed. The method is based on the analysis of forced oscillation of a cylindrical sample loaded with inertial mass. No special equipment or instrumentation other than the ordinary vibration measurement apparatus is required. Typical measurement of the viscoelastic properties of a silicone rubber $Silastic^{(R)}$ S2 were measured over the wide frequency range from 10 Hz to 3 kHz under the action of wide region of deformation from $10^{-4}%$ to 5%. It was shown that modulus of elasticity and loss tangent fall on the single curves when the ratio of load mass to sample mass changed from 1 to 20.

맥동유동하에 있는 유연성 있는 평판 사이의 벽면전단응력: 벽면운동과 임피던스 페이즈 앵글과 비뉴턴유체의 영향 (Wall Shear Stress Between Compliant Plates Under Oscillatory Flow Conditions: Influence of Wall Motion, Impedance Phase Angle and Non-Newtonian Fluid)

  • 최주환;이종선;김찬중
    • 대한기계학회논문집B
    • /
    • 제25권1호
    • /
    • pp.18-28
    • /
    • 2001
  • The present study investigates flow dynamics between two dimensional compliant plates under sinusoidal flow conditions in order to understand influence of wall motion, impedance phase angle (time delay between pressure and flow waveforms), and non-Newtonian fluid on wall shear stress using computational fluid dynamics. The results showed that wall motion induced additional terms in the streamwise velocity profile and the pressure gradient. These additional terms due to wall motion reduced the amplitude of wall shear stress and also changed the mean wall shear stress. The trend of the changes was very different depending on the impedance phase angle. As the impedance phase angle was changed to more negative values, the mean wall shear stress decreased while the amplitude of wall shear stress increased. As the phase angle was reduced from 0°to -90°under $\pm$4% wall motion, the mean wall shear stress decreased by 12% and the amplitude of wall shear stress increased by 9%. Therefore, for hypertensive patients who have large negative phase angles, the ratio of amplitude and mean of the wall shear stress is raised resulting in a more vulnerable state to atherosclerosis according to the low and oscillatory shear stress theory. We also found that non-Newtonian characteristics of the blood protect atherosclerosis by decreasing the oscillatory shear index.

액체 저장구조물의 유체-구조물 상호작용 해석 (FLUID-STRUCTURE INTERACTION ANALYSIS OF LIQUID STORAGE STRUCTURES)

  • 윤정방;김진웅;서정문;전영선
    • 전산구조공학
    • /
    • 제5권4호
    • /
    • pp.103-111
    • /
    • 1992
  • 본 논문에서는 직사각형 형태의 사용후 핵연료 저장구조물에 대한 내진해석을 다루었다. Eulerian과 Lagrangian의 두가지 해석방법을 사용하여, 그 결과를 비교하였다. Eulerian접근방법에서는 유체 운동에 대한 Laplace방정식의 경계치 문제를 푼 반면, Lagrangian 접근방법에서는 저장구조물은 고체 유한요소로 모형화 하였고, 내부유체는 유체 유한요소로 모형화 하였다. 유체영역을 모형화 하는데 사용된 유체요소의 강성을 적절히 산정하기 위하여 (1*1)의 감차적분을 적용하였다. 응답스펙트럼해석법으로 유체-구조물 상관관계의 내진해석을 수행한 결과, 두 접근방법으로 구한 벽면에 작용하는 유동압이 잘 일치함을 알 수 있었다. 또한 벽면 유연성의 영향을 포함할 경우, 지진 발생시 벽면에 작용하는 유동압이 크게 증가할 수 있음을 알았다.

  • PDF

난류 경계층에서 컴플라이언트 코팅과 점탄성 벽면의 방사 소음에 관한 실험적 연구 (Radiated Sound from Compliant and Viscoelastic Plates in a Turbulent Boundary Layer)

  • 이승배;이창준;권오섭;전우평
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2002년도 학술대회지
    • /
    • pp.779-782
    • /
    • 2002
  • We examine the problem in which porous/viscoelastic compliant thin plates are subject to pressure fluctuations under transitional or turbulent boundary layer. Measurements are presented of the frequency spectra of the near-field pressure and radiated sound by compliant surface. A porous plate consisting of 5mm thick, open-cell foam with fabric covering and a viscoelastic painted plate of 1mm thick over an acoustic board of 4m thick were placed over a rigid surface in an anechoic wind tunnel. Streamwise velocity and wall pressure measurements were shown to highly attenuate the convective wall pressure energy when the convective wavenumber ($k_{ch}$) was 3.0 or more. The sound source localization on the compliant walls is applied to the measurement of radiated sound by using an acoustic mirror system.

  • PDF

클라우드 컴퓨팅 정보보호 프레임워크에 관한 연구 (A Research on the Cloud Computing Security Framework)

  • 김정덕;이성일
    • 정보보호학회논문지
    • /
    • 제23권6호
    • /
    • pp.1277-1286
    • /
    • 2013
  • 탄력성(elasticity), 빠른 적용과 릴리즈, 광대역 네트워크 접속, 다중 접속(multi-tenancy), 활용에 제한이 없는(ubiquity) 유연성 등 클라우드 컴퓨팅의 고유한 속성들은 클라우드를 선택한 기업과 기관에게 획기적인 효율성을 제공하지만 원천적으로 내재된 보안 위협을 제거해야 하는 대책수립이 필요하다. 이를 위해 본 논문에서는 전략적 연계 모델을 참조하여 클라우드 컴퓨팅 정보보호 프레임워크를 제시하였다. 클라우드 컴퓨팅 정보보호 프레임워크는 클라우드 위협, 보안통제 활동, 클라우드 이해관계자를 중심 축으로 합목적성, 책임성, 투명한 책임소재의 벽면으로 구성된다. 중심 축은 클라우드 환경에서 정보보호 활동을 수행하는 주요 목적인 위협 최소화목표와 이해관계자를 지정하고 그들이 해야 할 정보보호 활동을 정의하고 있다. 또한, 3개 벽면은 클라우드 환경에서 정보보호 활동을 수행하기 위한 원칙이며 중심 축 간의 접점에서 7개 서비스 패키지 도출을 위한 방향을 제공한다.