• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.15-20
• /
• 2005

Most of studies for the ground load and ground behavior of landing gear have been conducted with an assumption that the structure of landing gear was rigid body. The assumption of rigid body during design process results in many errors or discrepancy. High ground load occurs in 3 directions on the shock absorbing strut during landing. This ground load initiated high structural deformation. In this study, the flex-multi-body dynamics is applied to adapt flexible bodies, so the results of analysis can be described close to landing gears real behaviour.

• Journal of KSNVE
• /
• v.9 no.6
• /
• pp.1259-1266
• /
• 1999

The objective of this investigation is to develop a compliant track link model and apply this model to the multi-body dynamic analysis of high mobility tracked vehicles. Two major difficulties encountered in developing the compliant track models. The first one is that the integration step size must be kept small in order to maintain the numerical stability of the solution. This solution deals with high oscillatory signals resulting from the impulsive contact forces and stiff compliant elements to represent the joints between the track links. The second difficulty is due to the large number of the system equations of motion of the three dimensional multibody tracked vehicle model. This problem was sloved by decoupling the equations of motion of the chassis subsystem and the track subsystems. Recursive methods are used to obtain a minimum set of equations for the chassis subsystem. Several simulation scenarios were tested for the high mobility tracked vehicle including accelaeration, high speed cruising, braking, and turning motion in order to demonstrate the effectiveness and validity of the methods proposed in this investigation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.6
• /
• pp.747-752
• /
• 2013

Recently, virtual test laboratory techniques have been widely used to reduce vehicle development costs and time. In this study, a virtual durability test process using multibody dynamics simulation and fatigue simulation is proposed. The flexible multibody model of the front half of a car suspension is solved using road loads that are measured from durability test courses such as a Belgian road. To verify the simulation results, the measured loads of components and simulation results are collated.

• Journal of the Korean Society for Railway
• /
• v.9 no.6 s.37
• /
• pp.792-797
• /
• 2006

In general, the Maglev vehicle is ran over the elevated guideway consisted of steel or concrete structure. Since the running behaviour of the vehicle is affected by the flexibility of the guideway, the consideration of the flexibility of guideway is needed for evaluation of dynamics of both the vehicle and guideway. A new technique based on flexible multibody dynamics is proposed to model the Maglev vehicle, levitation controller, and guideway into a coupled model. To verify the technique, an urban Maglev vehicle is analyzed using the technique and discussions are carried out.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.1
• /
• pp.31-40
• /
• 2021

Modern aircraft are high-performance and lightweight. Thus, the characteristics of the flexible structure appear and affect flight performance or limit it. These flexible characteristics need to be analyzed from the early stages of aircraft design. To this end, a program to analyze the dynamic and static behavior of flexible aircraft has been developed and the results are presented. Based on the multi-body dynamics simulation technique, rigid flight mechanics, structural vibrating behavior, and unsteady aerodynamics have been developed and integrated. Lastly, the level flight and the turn flight of the flexible characteristic aircraft have been analyzed using this integrated simulation program.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.3
• /
• pp.339-346
• /
• 2012

The pre-evaluation of the current-collection performance is an important issue for high-speed railway vehicles. In this paper, using flexible multibody dynamic analysis techniques, a simulation model of the dynamic interaction between the catenary and pantograph is developed. In the analysis model, the pantograph is modeled as a rigid body, and the catenary wire is developed using the absolute nodal coordinate formulation, which can analyze large deformable parts effectively. Moreover, for the representation of the dynamic interaction between these parts, their relative motions are constrained by a sliding joint. Using this analysis model, the contact force and loss of contact can be calculated for a given vehicle speed. The results are evaluated by EN 50318, which is the international standard with regard to analysis model validation. This analysis model may contribute to the evaluation of high-speed railway vehicles that are under development.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.2
• /
• pp.175-181
• /
• 2010

This paper presents the dynamic analysis method for estimating the performance of flat-type blades in wiper systems. The blade has nonlinear characteristics since the rubber is a hyper-elastic material. Thus, modal coordinate and absolute nodal coordinate formulations were used to describe the dynamic characteristic of the blade. The blade was structurally analyzed to find the bending characteristics of the cross section of the blade. According to the analysis results, the blade section is divided into three deformation bodies: rigid, small, and large. For the small deformation body, the modal coordinate formulation is used, while the absolute nodal coordinate formulation is used for the large deformation body. To verify the dynamic analysis result, an experiment was performed. The simulation and experiment results were compared to verify the flexible multi-body dynamic model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.10
• /
• pp.1039-1044
• /
• 2015

During the development of vehicles, durability tests are time consuming and costly. Recently, automobile companies have attempted to develop their own durability evaluation procedures by modifying and complementing . In this paper, we propose an integrated computer-aided engineering (CAE) method to evaluate the durability of a torsion beam axle (TBA). We compare this method with the standardized durability evaluation method used by an actual automobile company in order to determine the feasibility of this method. We compare the results with the test result data to enable us to estimate the reliability of the analysis results. In this study, we analyze the processes and results of the quasi-static fatigue analysis, and found improved methods and problems. Furthermore, we perform a thorough test using the requirements of the actual company. Based on the results, the structural analysis process in the quasi-static fatigue analysis method was superseded by the multi-body dynamics analysis process. Generally, this method is referred to as the resonance-fatigue analysis method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.10
• /
• pp.705-711
• /
• 2019

Dynamic behaviors of the deployable composite reflector antenna are numerically and experimentally investigated. Equations of the motion are formalized using Kane's equation by considering multibody systems with two degrees of freedom such as folding and twisting angles. To interpret structural deformations of the reflector antenna, the composite reflector is modeled using a beam model with the FSDT(First-order Shear Deformation Theory). To determine design parameters such as a torsional spring stiffness and a damping coefficient depending on deployment duration, an inverted pendulum model is simply applied. Based on the determined parameters, dynamic characteristics of the deployable reflector are investigated. In addition, its results are verified and compared through deployment tests using a gravity compensation device.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.8
• /
• pp.1015-1019
• /
• 2013

To improve the energy efficiency and ride quality of an electric vehicle, it is highly desirable to develop a lightweight suspension system with high travel ratio. Air suspension systems with a rubber tube are often considered optimal for such requirements. In this study, a new lightweight air suspension system with high travel ratio was developed for use in electric vehicles. Furthermore, an FE-based multi-flexible-body dynamics (MFBD) model of the suspension system was developed as a tool for improving the design of an actual suspension system. The MFBD model includes the FE modeling of the rubber tube module as well as other essential parts of the air suspension system. The system parameters for the model were obtained from various experiments. The validity of the developed MFBD model was shown through a comparison between the experimental results and the simulation results.