• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.1
• /
• pp.53-59
• /
• 2013

Since 1990s, the major recycling methods for mechanical recycling of FRP(Fiber Reinforced Plastics)boats has involved shredding and grinding of the scrap FRP in a new recycled product. But still it leads to secondary problem such as air pollution, unacceptable shredding noise level and few limited applications. This study is to propose a newly advanced method which is more efficient and environment friendly waste FRP regenerating system. As extracting FRP layer and making the recycled fiber for recycled-fiber reinforced concrete(RFRC) from waste FRP, the recycling process has some merits in a sense of the recycling energy and the environmental effects. In this study, for those tasks, spectro-chemical differentiation method and coloring water-soluble dye treatment makes the roving layer more distinguishable photophysically. Also that has remarkably reduced safety hazards and energy. Using the mechanical properties of polymers and composite, FRP with the orthotropic and laminated plastic structure has been easily separated in the new extracting system. Also the new method has introduced five kind of separating manuals for the some different compositions of FRP boats. The roving fiber of laminated glass-fiber layer is as good as the polyvinyl fiber which is cost-high commercial fiber to increasing strength of concrete products. The early study has shown the effectiveness of laminated glass-fiber layer which also is chemical-resistant due to the resin coating. These results imply that more efficient and environment friendly recycled glass fiber can be better applied to the fiber reinforced concrete(FRC) substitute and this study also has shown wide concrete applications with RFRC from the waste FRP boat.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.4
• /
• pp.145-150
• /
• 2014

GaN nanorods were grown on the apex of GaN stripes by three dimensional selective growth method. $SiO_2$ mask was partially removed only on the apex area of the GaN stripes by an optimized photolithography for the selective growth. Metallic Au was deposited only on the apex of the GaN stripes and a selective growth of GaN nanorods was followed by a metal organic vapor phase epitaxy (MOVPE). We confirmed that the shape and size of the GaN nanorods depend on growth temperature and flow rates of group III precursor. GaN nanorods were grown having a taper shape which have sharp tip and triangle-shaped cross section. From the TEM result, we confirmed that threading dislocations were rarely observed in GaN nanorods because of the very small contact area for the selective growth. Stacking faults which might be originated from a difference of the crystal facet directions between the GaN stripe and the GaN nanorods were observed in the center area of the GaN nanorods.

• Applied Chemistry for Engineering
• /
• v.26 no.3
• /
• pp.275-279
• /
• 2015

Poly(3,4-ethylenedioxythiophene) : poly(styrenesulfonate) (PEDOT : PSS) has attracted a great deal of attention as a transparent conductive material for organic solar cells or organic light-emitting diodes due to its high electrical conductivity, optical transparency, and excellent mechanical flexibility. It is well known that a solvent doping for PEDOT : PSS thin-films significantly increases the conductivity of films. In this paper, the effect of various kinds of solvent doping and post-treatment on the electrical and structural properties of PEDOT : PSS thin-films is investigated. The solvent doping greatly increases the conductivity of PEDOT : PSS thin-films up to 884 S/cm. A further enhancement of the conductivity of PEDOT : PSS thin-films is achieved by the solvent post-treatment which raises the conductivity up to 1131 S/cm. The enhancement is mainly caused by the depletion of insulating PSS and forming conducting PEDOT-rich granular networks. Strong optical absorption peaks at the wavelength of 225 nm of PEDOT : PSS thin-films indicate the depletion of insulating PSS by post-treatment. We believe that the solvent post-treatment is a promising method to achieve highly conductive transparent PEDOT : PSS thin-films for applications in efficient, low-cost and flexible organic devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.183-183
• /
• 2009

OLED소자의 양극재료로써 현재는 산화인듐주석(ITO : indium tin oxide) 박막이 널리 이용되고 있다. 그러나 낮은 전기 비저항과 높은 투과도를 갖는 ITO 박막을 얻기 위해서는 $300^{\circ}C$ 이상의 고온에서 성막되어야 하며, 원료 물질인 인듐의 수급량 부족으로 인한 문제점과 독성, 저온증착의 어려움, 스퍼터링 시 음이온 충격에 의한 막 손상으로 저항의 증가의 문제점이 있고, 또한 유기발광소자의 투명전극으로 쓰일 경우에 유기물과의 계면 부적합성, 액정디스플레이의 투명전극으로 사용될 경우에 $400^{\circ}C$정도의 놓은 온도와 수소 플라즈마 분위기에서 장시간 노출 시 열화로 인한 광학적 특성변화가 문제가 된다. 이러한 문제점을 지닌 ITO 박막을 대체할 수 있는 물질로 산화 인듐아연(lZO) 박막이 많은 각광을 받고 있다. IZO(Indium Zinc Oxide) 박막은 저온 ($100^{\circ}C$ 이상)에서 증착이 가능하고 추가적인 열처리 없이도 가시광 영역에서 90% 이상의 광 투과도와 ${\sim}10^{-4}{\Omega}cm$ 이하의 낳은 전기 비저항을 갖는 것으로 알려져 있다. 이러한 IZO박막은 성막 후 고온의 열처리 과정이 필요 없기 때문에 폴리카보네이트와 같은 유기물 기판을 사용하여 제작 가능한 유연한 평판형 표시 소자의 제작에도 적용될 수 있다. IZO(Indium Zinc Oxide) 박막은 상온 공정에서도 우수한 전기적, 광학적, 표면 특성을 나타낼 뿐만 아니라 양극재료로써 높은 일함수를 가지고 있어 고효율의 유기 발광 소자를 구현하는데 유리한 재료라 판단된다. 본 연구에서는 TCO 박막의 면 저항과 표면 거칠기가 OLED 소자의 성능에 미치는 영향을 조사하였다. R.F Magnetron Sputtering을 이용하여 투명 전도막을 성막 형성 하였으며, 기판온도와 증착과정에서 주입되는 산소, 수소의 유랑 변화가 박막의 구조적, 전기적 특성에 어떠한 영향 미치는 것인가를 자세히 규명하였다 ITO 와 IZO박막은 챔버 내 다양한 가스 분위기(Ar, $Ar+O_2$ and $Ar+H_2$) 에서 R.F Magnetron Sputtering 방법으로 증착했다. TCO박막의 구조적인 이해를 돕기 위해서 X-ray diffraction 과 FESEM으로 분석했다. 광학적 투과도와 박막의 두께는 Ultraviolet Spectrophotometer(Varian, cary-500)와 Surface profile mersurement system으로 각각 측정하였다. 면저항, charge carrier농도, 그리고 TCO박막의 이동성과 길은 전기적특성은 Four-point probe와 Hall Effect Measurement(HMS-3000)로 각각 측정한다. TCO 박막의 표면 거칠기에 따른 OLED소자의 성능분석 측면에서는 TCO 박막의 표면 거칠기 조절을 위해 photo lithography 공정을 사용하여 TCO 박막을 에칭 하였다. 미세사이즈 패턴 마스크가 사용되고 에칭의 깊이는 에칭시간에 따라 조절한다. TCO박막의 표면 형태는 FESEM과 AFM으로 관찰하고 그리고 나서 유기메탈과 음극 전극을 연속적으로 TCO 박막위에 증착한다. 투명전극으로 사용되는 IZO기판 상용화를 위해 IZO기판 위에 $\alpha$-NPB, Alq3, LiF, Al순서로 OLED소자를 제작하였다. 전류밀도와 전압 그리고 발광과 OLED소자의 전압과 같은 전기적 특성은 Spectrometer (minolta CS-1000A) 에 의하여 I-V-L분석을 했다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.1
• /
• pp.11-23
• /
• 2014

Wireless Mesh Network(WMN) has drawn much attention due to easy deployment and good scalability. Recently, major power utilities have been focusing on R&D to apply WMN technology in Smart Grid Network. Smart Grid is an intelligent electrical power network that can maximize energy efficiency through bidirectional communication between utility providers and customers with ICT(Information Communication Technology). It is necessary to guarantee QoS of some important data in Smart Grid system such as real-time data delivery. In this paper, we suggest QoS enhancement method for WMN based Smart Grid system using IEEE 802.11s. We analyze Smart Grid Application characteristics and apply IEEE 802.11s WMN scheme for Smart Grid in domestic power communication system. Performance evaluation is progressed using NS-2 simulator implementing IEEE 802.11s. The simulation results show that the QoS enhancement scheme can guarantee stable bandwidth irrespective of traffic condition due to IEEE 802.11s reservation mechanism.

• Korean Journal of Ichthyology
• /
• v.27 no.2
• /
• pp.63-70
• /
• 2015

This research is about spawning behavior and morphological development of the eggs and larvae of fringed blenny which lives in Korean sea. It helps to find out the relation between fringed blenny larvae and other stichaeidae larva. Moreover, it is going to use for the basic data of taxonomical research. There were 8 mother fishes (total length 31.8~34.0 cm, average $32.9{\pm}0.21cm$), which were captured from the cost of Sindeok-dong, Yeosu-si, Jeollanam-do from December, 2010. we used trap to capture them. Mother fishes were brought to glass aquarium ($50{\times}30{\times}35cm$) and nurtured with recirculate rearing system. Breeding water temperature was $12.3{\sim}15.8^{\circ}C$ (average $14.1{\pm}2.47$) and salinity was 32.5~33.5‰ (average $33.0{\pm}0.05$‰). fertilized egg was round, opaque demersal egg. The size was 1.81~2.19 mm (average $2.00{\pm}0.27mm$, n=50). Incubation was begun after 271 hours and 30 minutes from fertilization. It started with piercing the egg membrane. prelarvae had length of 8.45~8.84 mm (average $8.65{\pm}0.28mm$, n=5) right after the incubation, and both mouth and anus were opened. After 11 days from the incubation, postlarvae had length of 10.5~11.3 mm (average $10.9{\pm}0.57mm$), and the number of myotomes was increased to 66.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.252-252
• /
• 2016

최근 학계나 산업계에서 indium tin oxide (ITO)의 높은 전기 전도도 및 광투과율을 이용하여 줄 발열을 기초로 하는 투명 면상 발열체에 대한 연구가 활발히 진행 되고 있다. 하지만 단일 ITO 박막으로 제작한 투명 면상 발열체는 온도가 상승함에 따라 균일하게 발열 되지 않으며, 글라스의 곡면 부분에서 유연성이 부족하여 크랙이 발생하는 다양한 문제점들을 가지고 있다. 이를 해결하기 위해 ITO의 결정화 온도 $160^{\circ}C$ 이상의 고온공정 또는 증착 후 열처리가 필요 하는 추가적인 공정이 필요하다. 따라서 본 연구에서는 단일 ITO 박막의 단점을 개선하는 ITO/Ag/ITO 하이브리드 구조의 투명 면상 발열체를 제작하여 전기적, 광학적 특성을 비교하고 발열량, 온도 균일성, 발열 유지 안정도를 조사하였다. 본 연구에서는 $50{\times}50mm$ 크기의 non-alkali glass (Corning E-2000) 기판 상에 마그네트론 스퍼터링 공정으로 상온에서 ITO/Ag/ITO 박막을 연속적으로 증착 하여 다층구조의 하이브리드 형 투명 면상 발열체를 제조하였다. 박막 증착 파워는 DC (Ag) power 100 W, RF (ITO) power 200 W로 하였으며 ITO박막두께는 40 nm로 고정 시키고 Ag박막 두께는 10 ~ 20 nm로 변화를 주었다. 증착원은 3인치 ITO 단일 타깃(SnO2, 10 wt.%)과 Ag 금속 타깃 (순도 99.99%)을 사용하였으며, 고순도 Ar을 이용하여 방전하였으며 총 주입량은 20 sccm, working pressure는 1.0 Pa을 유지하였다. 증착전 타깃 표면의 불순물 제거와 방전의 안정성을 유지하기 위해 10분간 pre-sputtering을 진행하고 증착하였다. 증착한 박막의 전기적, 광학적 특성은 각각 Hall-effect measurements system (ECOPIA, HMS3000), UV-Vis spectrophotometer (UV-1800, SHIMADZU)으로 측정하였으며, 하이브리드 표면의 구조 및 형상은 field emission-scanning electron microscopy (FE-SEM, Hitachi S-4800)으로 관찰하였다. 또한 투명 면상 발열체의 성능은 0.5 ~ 3 V/cm의 다양한 전압을 power supply (Keithly 2400, USA)를 통해서 시편 양 끝단에 인가한 후 시간에 따른 투명면상 발열체의 표면 온도변화를 infrared thermal imager (IR camera, Nikon)를 이용하여 관찰하였다. 하이브리드 구조를 가진 ITO박막의 두께는 40 nm로 고정 시키고 Ag박막의 두께는 10, 15, 20 nm로 변화를 주었다. 이들 박막의 면저항 값은 각각 5.3, 3.2, $2.1{\Omega}/{\Box}$였으며, 투과도는 각각 86.9, 81.7, 66.5 %였다. 이에 비해 두께 95 nm의 단일 ITO박막의 면저항 값은 $59.5{\Omega}/{\Box}$였으며, 투과도는 89.1 %였다. 하이브리드 구조의 전기적특성은 금속층의 두께가 증가할수록 캐리어 농도 값이 증가함에 따라 비저항 값이 감소되어 면저항 값도 감소된 것이며, 금속 삽입층의 전도특성이 비저항에 큰 영향을 주고 있음을 보여준다. 하지만 금속 층의 두께가 증가할수록 Ag층이 연속적인 막을 형성하여 반사율이 증가함에 따라 투과도가 감소하였다. 따라서 하이브리드 구조를 가진 투명 면상 발열체에 금속 삽입층의 두께 조절은 매우 중요한 인자임을 확인 할 수 있었다. 또한 발열성능을 평가 하기 위해 시편 양 끝단에 3 V전압을 인가한 결과, 금속 삽입층의 두께가 10 nm에서 5 nm씩 증가한 하이브리드 구조를 가진 투명면상 발열체의 최고 온도는 각각 98, 150, $167^{\circ}C$ 였으며, 단일 ITO의 최고 온도는 $32^{\circ}C$였다. 이 것은 동일한 두께 (95 nm)의 단일 ITO 박막과 비교하여 면저항이 낮은 하이브리드 박막의 발열량은 약 $120^{\circ}C$로 발열효율이 매우 우수한 것을 확인 할 수 있었다.

• Science of Emotion and Sensibility
• /
• v.20 no.3
• /
• pp.141-150
• /
• 2017

The purpose of this study was to analyze the effect of the shape and attached position of E-textile-based stretchable sensors on motion-sensing performance and to investigate the requirements for the optimal structure of clothes for sensing limb motions. An experimental garment was prepared with different sensor shapes, and attachment positions. A child subject, wearing the experimental garment, performed arm and leg bending and extension motions at $60^{\circ}$, $90^{\circ}$ and $120^{\circ}$ motion angles, at a rate of 60 deg/sec. The changes in voltage triggered by the stretching and contracting of the fabric-sensor were measured, and an acceleration sensor was utilized to verify that the experimental motions were correctly performed. Dummy arms and legs of a child were manufactured to perform an identical test, in order to compare the dummy results with the actual human body experiment results. The analysis showed that the reproducibility and reliability of the rectangular sensor, showing uniform and stable were higher than those of the boat-shaped sensor, in both the dummy and the human body experiments. The attachment position of the sensor was more reproducible and reliable when placed on 4 cm below the elbow and knee joints in the dummy test, when placed in the joints of the elbow and knee, in children experiment. The appropriate shapes and attached positions of the sensor for sensing the motions were analyzed, and the results proved that motion-sensing of the human body is possible by utilizing flexible fabric-sensors integrated into clothes.

• Journal of KIISE
• /
• v.44 no.2
• /
• pp.213-222
• /
• 2017

The Internet of Things (IoT) technology is rapidly developing in recent years, and is applicable to various fields. A smart factory is one wherein all the components are organically connected to each other via a WSN, using an intelligent operating system and the IoT. A smart factory technology is used for flexible process automation and custom manufacturing, and hence needs adaptive network management for frequent network fluctuations. Moreover, ensuring the timeliness of the data collected through sensor nodes is crucial. In order to ensure network timeliness, the power consumption for information exchange increases. In this paper, we propose an IEEE 802.15.4e DSME-based distributed scheduling algorithm for mobility support, and we evaluate various performance metrics. The proposed algorithm adaptively assigns communication slots by analyzing the network traffic of each node, and improves the network reliability and timeliness. The experimental results indicate that the throughput of the DSME MAC protocol is better than the IEEE 802.15.4e TSCH and the legacy slotted CSMA/CA in large networks with more than 30 nodes. Also, the proposed algorithm improves the throughput by 15%, higher than other MACs including the original DSME. Experimentally, we confirm that the algorithm reduces power consumption by improving the availability of communication slots. The proposed algorithm improves the power consumption by 40%, higher than other MACs.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.10 no.4
• /
• pp.287-294
• /
• 2016

Based on upper limb torque by different angles of a back, distance between crank axis and chest and angles of hand-grips, this research is to develop variable hand bikes. By doing so, it is to offer guidance for its design. For this research three normal persons took part in the experiment. Results are as follows. First, upper limb torque was found to be the highest at 50 degree of a back and muscle endurance was shown to be the highest at 80 degree of a back. It means that as a back of a chair gets lower the speed and efficiency becomes better, which contradicts the subjective fact that K-type hand bikes would show the highest speed. Second, among types of grips of hand bikes 45 degree ones have been shown to be the ones with the highest torque. This is due to proper distribution of power of joints in arms, elbows, and shoulders. Third, in case of distance of 45cm between crank axis and chest, it has shown the most efficient torque. This is because of the effect of gravity and exhaustion when handling.