• The Journal of Korean Society for Radiation Therapy
• /
• v.26 no.2
• /
• pp.199-206
• /
• 2014

Purpose : According to the rapid increase recently in image-guided radiation therapy, It is necessary to control of the image guidance system completely. In particular for the main subject to the accuracy of image guided radiation therapy device to be done essentially the quality assurance. We made efficient phantom in AMC for the management of the accurate and efficient. Materials and Methods : By setting up of five very important as a quality assurance inventory of the Image guidance system, we made (AMC G-Box) phantom for quality assurance efficient and accurate. Quality assurance list were the Iso-center align, the real measurement, the center align of four direction, the accuracy of table movement and the reproducibility of Hounsfield Unit. The rectangular phantom; acrylic with a thickness of 1 cm to $10cm{\time}10cm{\time}10cm$ was inserted the three materials with different densities respectively for measure the CBCT HU. The phantom was to perform a check of consistency centered by creating a marker that indicates the position of the center fixed. By performing the quality assurance using the phantom of existing, comparing the resulting value to the different resulting value using the AMC G-Box, experiment was analyzed time and problems. Therapy equipment was used Varian device. It was measured twice at 1-week intervals. Results : When implemented quality assurance of an image guidance system using AMC G-Box and a phantom existing has been completed, the quality assurance result is similar in $0.2mm{\pm}0.1$. In the case of the conventional method, it was 45 minutes at 30 minutes. When using AMC G-Box, it takes 20 minutes 15 minutes, and declined to 50% of the time. Conclusion : The consistency and accurate of image guidance system tend to decline using device. Therefore, We need to perform thoroughly on the quality assurance related. It needs to be checked daily to consistency check especially. When using the AMC G-Box, It is possible to enhance the accuracy of the patient care and equipment efficiently performing accurate quality assurance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.3
• /
• pp.203-211
• /
• 2016

In contrast with STT missiles, the guidance law design for BTT missiles should be based on 3-dimensional pursuit kinematics, since the pitch and roll channels of BTT missiles are coupled dynamically. More generally than the prior works, the dynamics of pitch and roll channels, as well as 3-dimensional pursuit kinematics are considered in the design of our terminal-phase optimal guidance law for BTT missiles proposed in this paper. Thereby, the proposed optimal guidance law guarantees high capturability with small miss distance without significant performance degradation due to time-lag effect even in case of relatively slow autopilot dynamics. Moreover, the resulting optimal guidance law is expressed explicitly in feedback-form with the coefficients given as the functions of time-to-go. The effectiveness and practicality of our work is demonstrated through various simulation results.

• ICROS
• /
• v.3 no.2
• /
• pp.20-25
• /
• 1997

이 글에서는 전술유도무기체계에서 호밍유도의 PNG 다음으로 많이 채택하고 있는 시선지령유도의 유도루우프 설계기술에 대해 논하고자 한다. 이를 위해 유도루우프를 구성하고 있는 부체계인 표적추적장치, 오차보상기, feedforward 보상기에 대해 살펴보고 유도루우프를 설계할 때 고려해야 할 유도오차를 발생시키는 요인인 표적의 기동, glint noise 등의 영향에 대해 분석한다. 또한 유도탄의 기동력과 지령수신기의 수신감도에 따라 결정되는 명중영역의 산출과 시선유도의 발전추세에 대해 언급하고자 한다.

• Fire Science and Engineering
• /
• v.21 no.4
• /
• pp.115-122
• /
• 2007

Exiting systems are essential to prevent casualties in case of fire. However, existing guidance systems are lack of flexibility because their functionalities are fixed when they are planned. In this paper, a system is introduced which guides evacuees in realtime by processing data it gathers throughout various sensors in realtime. It is planned and designed to aid quick and efficient evacuation, and produced, installed and tested in an underground space to show its feasibility. In building the system, ubiquitous techniques are employed for its sensor network and evacuee positioning in an attempt to make it cheap and extendable.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.544-549
• /
• 2017

This paper aims to examine the effect of rotational fluid motion about the efficiency of the gas - liquid ejector, which is a core unit in a ship equilibrium water treatment system. The ejector is a device for injecting ozone into ship equilibrium by the negative pressure generated by exchange of momentum between water and ozone. The existing ejector ejects the driving fluid with a simple form. In this paper, however, a rotation induction device is applied to the driving nozzle so that the driving fluid can be rotated and injected. To investigate the flow characteristics by the rotational movement of the driving fluid, CFD was used. The pressure and flow rate of the driving fluid, the negative pressure and suction flow rate of the suction fluid in the suction part, and the discharge pressure were predicted. On the basis of the results, the efficiency of the ejector using the rotation induction system was 22.25%, which was about 1.7% better than that of the existing ejector. Finally, to verify the feasibility of the CFD, an experiment was conducted on the ejector using the rotation induction device and the results were similar to those of the CFD.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.34 no.4
• /
• pp.93-99
• /
• 2022

Analytical solutions for regular waves generated by bottom wave makers in a 3-dimensional wave basin were derived in this study. Bottom wave makers which have triangular, rectangular and combination of two shapes were adopted. The 3-dimensional velocity potential was derived based on the linear wave theory with the bottom moving boundary condition, kinematic and dynamic free surface boundary conditions in a wave basin. Then, analytical solutions of 3-dimensional particle velocities and free surface displacement were derived from the velocity potential. The solutions showed physically valid results for regular waves generated by bottom wave makers in a wave basin. The analytical solution for obliquely propagating wave generation from bottom wave maker which works like a snake was also derived. Numerical results of the solution agree well with theoretically predicted results.

• The Science & Technology
• /
• no.6 s.433
• /
• pp.96-100
• /
• 2005

• 전기의세계
• /
• v.29 no.3
• /
• pp.145-149
• /
• 1980

차량용유도전동기의 인버어터 제어방식의 실용화에서 생기는 문제점을 살펴보면, 첫째, 유도전동기의 인버어터제어방식은 차량동력방식에 적합한 많은 장점을 갖고 있으며, 둘째, 우수한 점착성능이 얻어지고 또 유도장해에 대하여서도 쵸퍼제어방식과 동등한 수준으로 가져갈 수 있고 세째, 중량에서 제어장치는 쵸퍼제어방식에 비하여 인버어터제어방식이 약간 무겁지만 주전동기를 경량화할 수 있어 전체로서는 쵸퍼제어방식과 같은 정도로 가져갈 수 있다는 점이다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.3
• /
• pp.124-128
• /
• 1999

The object of the present study is to obtain a 20[kHz], 10[kW] rating, high efficiency induction heating system by high frequency serises-resonant inverter. Proposed is a topology that minimize a reactive power, by which direct iOIrt voltage is variable corresponding to the variation of the load, heated-object, and by which the switching of inverter is forced to follow a resonant frequency. And assured that the power foctor of the inverter in a induction heating system is proper about O.96 through the simulation and results.esults.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.235-237
• /
• 2018

In spite of the superiority of the sliding method in the building construction field, the AC induction motor servo control device is used as the power control technology in the building construction field in order to improve the problems of the hydraulic power control method, thereby contributing to the precision control and the productivity improvement. Based on Induction Motor Servo Controller, we proposed the development of a mobile sliding method using a complex combination of PC and MITY (MS) Servo.