• Proceedings of the KSRS Conference
• /
• 2009.03a
• /
• pp.78-81
• /
• 2009

레일형 GB-SAR의 단점을 극복하고자 차량에 원형레일을 탑재하여 신속한 기동을 확보하고 합성구경의 길이를 늘리며 영상영역을 확장한 ArcSAR를 세계 최초로 설계하고 시작품을 제작하였다. ArcSAR의 핵심기술이라고 할 수 있는 원형레일은 알루미늄 프로파일로 제작한 회전디스크, 곡선가이드, 리니어 가이드로 구성되며, 서보모터를 이용하여 구동된다. 회전디스크의 지름은 2.1 m 이며, 회전 디스크 위에 장착된 곡선 가이드를 따라 안테나가 탑재된 리니어 가이드가 이동하며 정밀한 원형 운행을 하게 된다. 리니어 가이드는 슬라이드식으로 제작되어 최대 3 m 까지 확장이 가능하여 스폿 모드 측정시 6 m 길이의 레일에서의 자료 획득과 유사한 결과를 얻게 된다. SAR 측정 장비는 회전디스크 위에 장착되어 전원을 제외한 별도의 슬립링을 사용을 자제하였다. 레일의 구동과 자료의 획득은 LabVIEW 기반의 통합 제어측정 소프트웨어를 통해 구현하였으며, 실내 실험 및 현장적용 실험을 통해 가능성을 확인하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.11
• /
• pp.1051-1061
• /
• 2004

In this Paper, a new antenna(VHMDA) characteristics of half-circular/elliptical disc-loaded planar antennas with horizontally top-loaded small disc is studied by simulation and measurements with additional resonant structure. The transfer function characteristics of Gaussian pulse from the designed UWB transmitter antenna has been investigated. The radiation pattern of the proposed antenna in azimuth is nearly omni-directional response, which is usulally required in conventional monopole antenna. In addition to that, the simulation and measured results show that the return loss characteristics of VHDMA covers considerably large bandwidth with small area. From the measured results of the circular and half-circular disc-loaded monopole antennas with small disc mounted on the top, it is found that the half disc-loaded monopole antenna with additional structure can be comparable to the circular disc-loaded monopole antenna in respect o( size and electrical performances. Surface wave and dielectric losses often caused by the printed antenna using high dielectric constant does not occur in metallic planar antenna with good impedance matching and without lossy matching unit. This structure implies that the performance of return loss is directly related with the radiation efficiency.

• Journal of the Korean Society of Visualization
• /
• v.19 no.1
• /
• pp.88-93
• /
• 2021

For a flow normal to a circular disk, the flow separation occurs from the edge of the disk and the flow recirculation zone exists behind the disk. Many existing studies conducted simulations of flow normal to a circular disk under low Reynolds numbers. Some studies performed LES or DES simulations under high Reynolds numbers. However, comparative study for different RANS models for high Reynolds numbers is very limited. This study presents numerical simulations of a flow normal to a circular disk using Realizable k-ε model and SST k-ω model. The recirculation bubble length and drag coefficient were compared with the experimental data. The SST k-ω model showed the excellent predictions for the recirculation bubble length and drag coefficient.

• Proceedings of the Korean Information Science Society Conference
• /
• 2012.06c
• /
• pp.180-182
• /
• 2012

플래시 메모리는 고성능, 저전력 등 많은 장점을 가지고 있어 PC를 비롯한 각종 단말에서 아주 많이 사용되고 있다. 하지만 기존의 시스템들은 디스크 기반 저장 장치의 특성을 고려하여 설계되었기 때문에 플래시 메모리 저장 장치에 맞게 수정한다면 더욱 좋은 성능을 기대할 수 있다. 본 논문에서는 그 중에서도 파일 시스템 및 데이터베이스에서 많이 쓰이고 있는 해시 인덱스 기법을 플래시 메모리 저장 장치에 특성에 맞춘 원형 해시 인덱스 기법을 제안한다. 원형 해시 인덱스 기법은 New Dynamic Hashing 기법의 단점을 보완하여 보다 나은 성능을 제공한다.

• Journal of the Korea Convergence Society
• /
• v.11 no.11
• /
• pp.233-237
• /
• 2020

In this study, the thermal analysis on the brake disc of electric kickboard was analyzed. The different heat is transmitted depending on the pad contact surface of brake disc. The trend that the temperature decreases at the part away from the contact surface was almost constant. And model A showed a slightly lower temperature distribution than model B. Model A has a maximum equivalent stress of 7% higher than model B. By being applied with the higher heat transfer above the contact surface, it is thought that model B has a greater strength than model A if the design takes into account the corner of the brake disc. If this study result is utilized to the design of electric kickboard, the design of brake disc with better strength is considered to be established. The durability of brake against the heat can be evaluated by applying this study result to the brake disc of electric kickboard. And it is seen that the result can be the design of brake with strength and the aesthetic convergence.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.8
• /
• pp.1029-1034
• /
• 2010

In this paper, we present the roundness profile and run-out error measurement for a rotating shaft. The devices for measuring the roundness require a precision rotation table which is used as a reference to obtain the circular profile. Therefore, the roundness measuring system is expensive and requires precision manufacturing. The two-point method for succession measurement has been used to obtain a linear profile or used in straightness measurement using two displacement measuring devices. In this paper, the method is used for measuring the circular profile of a rotating shaft. A method to remove the vibration of the shaft, i.e., the run-out, is used, and the original circular profile is obtained from the measured raw data that excludes the run-out error of the rotating shaft. This method will be useful for obtaining the precise circular profile without using a precision reference circular artifact.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.3
• /
• pp.213-220
• /
• 2000

The method of photoelasticity allows one to obtain principal stress differences and principal stress directions in a photoelastic model. In the classical approach, the photoelastic parameters are measured manually point by point. The previous methods require much time and skill in the identification and measurement of photoelastic data. Fringe phase shifting method has been recently developed and widely used to measure and analyze fringe data in photo-mechanics. This paper presents the test results of photoelastic fringe phase shifting technique for the stress analysis of a circular disk under compression and an edge-cracked plate subjected to tensile load. The technique used here requires four phase stepped photoelastic images obtained from a circular polariscope by rotating the analyzer at $0^{\circ}$, $45^{\circ}$, $90^{\circ}$ and $135^{\circ}$. Experimental results are compared with those or FEM. Good agreement between the results can be observed. However, some error may be included if the technique is used to general direction which is not parallel to isoclinic fringe.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.6
• /
• pp.866-878
• /
• 1999

In this paper, stripline circulator including a ferrite resonator which is consisted of a circular disk and two annuli disks is designed and fabricated. Using RGF(Recursive Green Function) technique, electromagnetic field of port and input impedance is presented. The circulator characteristics are compared according to the ferrite arrangement, bias field intensity and port width. The pass-band frequency of the fabricated circulator using the designed data is from 1.55 GHz to 2.95 GHz, the reflection coefficient $S_{11}$ of input port is -30 dB, and the transmission coefficient $S_{21}$ between input port and isolation port is -28 dB at resonating point 2.38 GHz.

• 한국IT서비스학회:학술대회논문집
• /
• 2009.05a
• /
• pp.341-344
• /
• 2009

네트워크(Network) 라우터(Router)와 스위치(Switch) 장치에서 수많은 패킷(Packet)이 통과된다. 네트워크에 연결된 컴퓨터가 20대일 경우에 일일 평균 패킷 전송양은 약 400GB 정도에 이른다. 이러한 패킷 데이터를 분석하기 위해서는 수집된 데이터를 디스크 장치에 저장할 수 있는 대규모의 저장공간과 주기적인 백업이 필요하다. 수집된 데이터 원형에는 사용자가 원하는 정보뿐만 아니라 불필요한 정보가 산재해있다. 따라서 수집된 데이터를 원형 그대로 저장하는 것이 아니라 원하는 정보(Information)와 지식(Knowledge)이 유지되고 쉽게 식별될 수 있도록 데이터를 가공해서 요약된 정보를 유지하는 것이 효과적이다. 전 세계적으로 네트워크를 통과하는 패킷 데이터의 양이 헤아릴 수 없을 만큼 증가하고, 인터넷 보급률이 증가함에 따라서 인터넷 사용자 및 소비자의 정보 분석의 필요성이 부각되고 있다. 본 논문에서는 네트워크에서 수집된 패킷 데이터에 적합한 데이터 전처리 기법(preprocessing)을 제안한다.

• Transactions of Materials Processing
• /
• v.21 no.1
• /
• pp.19-23
• /
• 2012

In this paper, a Mannesmann roll piercing process equipped with Diecher's guiding discs is investigated using a rigid-thermoviscoplastic finite elements method with intelligent remeshing capability and tetrahedral elements. The analysis model is presented and the approach is applied to a Mannesmann roll piercing process found in the literature. Details about the remeshing criterion as well as mesh density control are given. The present predictions are compared with the predictions found in the literature, showing that the two predictions are in close agreement in terms of the deformed shape. However, it is emphasized that the present approach has the distinct strength in predicting details of final shape.