• Textile Coloration and Finishing
• /
• v.32 no.4
• /
• pp.239-244
• /
• 2020

Polyethylene (PE) micro-fiber have been prepared at different hot air temperature (60, 80 and 100 ℃) and different pressure (20, 40, 60 and 80 kPa) by melt centrifugal spinning technique. The parameters of melting centrifugal spinning including polymer contents, rotational velocity, temperature of hot air and pressure were optimized for the fabrication process. The study showed that 8000 rpm rotational velocity, 80 ℃ heated hot air and 40 kPa air pressure are the best condition to obtain uniform and strong PE fiber. The prepared PE fibers were analyzed by field emission scanning electron microscope and universal testing machine and found that fibers with reduced diameter and improved tensile strength are obtained at hot air condition.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.4
• /
• pp.39-47
• /
• 2004

The SCP(sand compaction pile) method which is a vertical reinforcing technique for soft ground using a sand compaction pile has received increasing popularity in Korea. Currently, there are different methods to evaluate the bearing capacity of the reinforced ground by the SCP method. However, a method that can consider the effect of the replacement ratio on the bearing capacity is not yet available. This study investigated the effect of the replacement ratio on the bearing capacity of the reinforced ground by the SCP method. The study involved laboratory experiments which were conducted on a centrifuge facility. Test conditions included various ranges of replacement ratios (20, 30, and 40%), centrifuged consolidation, and loading. From the results of the study, a method which can evaluate the bearing capacity of the reinforced ground was proposed and verified using the weighted average of the replacement ratio.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.8
• /
• pp.1546-1552
• /
• 2016

In addition, because it uses preheating to dissolve an alloy in general, it is hard to regulate the appropriate melting temperature of the alloy and brewing time and shows the defect of the supplementation thing due to the super-heating. Once the alloy is molten and then most of the casting by attaching a sight glass or non-contact temperature sensor is suitable casting temperature the operator pressing a button to generate a centrifugal force to inject the molten alloy into a crucible in the casting ring. These results, and most of the cast temperature is too high or too low to generate a lot of casting defects do not get into a uniform cast body. In this paper, we developed a dental casting machine for high frequency using a single temperature sensor which can measure the actual temperature of the alloy than the temperature of the external non-contact measurement using a temperature sensor.

• Korean Journal of Food Science and Technology
• /
• v.32 no.1
• /
• pp.147-153
• /
• 2000

We could produce algin-like biomaterial of polyiduronan using polyglucuronic acid C5-epimerase with polyglucuronic acid prepared by specific oxidation of primary alcohol groups of four kinds of polysaccharides(corn starch, rice starch, sweet potato starch, and cellulose). The enzyme activity was determined by the modified Dische carbazole methodology with the isolated crude enzyme from the supernatant centrifuged at $100,000{\times}g$ for 1 hr after grinding fresh bovine liver. And then, the optimal substrate, pH, and temperature for the enzyme reaction of polyglucuronic acid C5-epimerase were determined as the oxidized sweet potato starch, 7.0, and $30^{\circ}C$, respectively. Conclusively, it could be possible to epimerize polyglucuronic acid in the oxidized sweet potato starch to polyiduronic acid. Therefore, we could obtain algin-like polysaccharide using the oxidized sweet potato starch and polyglucuronic acid C5-epimerase isolated from bovine liver.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.140-140
• /
• 2018

다수의 자연 하천은 사행의 형태를 가지고 있으며 자연 상태에서의 직선 하천 형태는 비율이 20% 이하이다. 이러한 하천의 사행 형상으로 인하여 편수위 발달, 횡방향 압력의 불균형, 그리고 수심차에 의한 원심력이 발생하여 이차류 흐름이 발생된다. 정확한 이차류 구현을 위해서는 3차원 모형을 사용하는 것이 바람직하나, 3차원 모형의 격자 구성과 사용에서는 상당한 시간 및 노력이 요구되기 때문에 수심적분 2차원 모형을 사용하면서도 이차류의 영향을 구현하기 위한 연구들이 이루어졌다. 본 연구에서는 이러한 이차류의 영향을 2차원 모형으로 구현하고자 하였으며 이를 위해 이차류 연직 분포에 대한 기존 연구를 검토하여 새로운 이차류 공식을 개발하였다. 그리고 한국건설기술연구원 하천실험센터의 실규모 실험을 통해서 이차류 공식에 사용되는 계수를 보정하였다. 이처럼 개발된 식은 이차원 수리해석 모형인 HDM-2D에 적용되었다. HDM-2D는 수심 적분된 2차원 운동량 방정식을 지배방정식으로 사용하는 수리해석모형으로서, 이차류의 영향을 반영하기 위하여 개발한 황방향 유속의 연직분포식을 분산 응력항에 대입하여 이차류에 의한 전단 효과를 구현하였다. HDM-2D 흐름 모의 수행 결과와 하천실험센터 실험결과와 비교하여 이차류 효과가 주 흐름 유속의 분포에 미치는 영향을 확인하였다. 분석 결과, 모의 결과는 실험에서 발생하는 유속의 주 흐름 분포가 바깥쪽으로 편중되는 현상을 적절하게 재현함을 알 수 있었다. 모의 결과를 통해 HDM-2D 모형이 이러한 이차류 영향을 구현할 수 있음을 확인하였으며, 사행수로에서 주 흐름분포의 재분배는 하천 환경에서 유사 이동 및 오염물 이동에 큰 영향을 미칠 것으로 판단된다.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.4
• /
• pp.33-44
• /
• 2013

Mononobe-Okabe (M-O) theory is widely used for evaluating seismic earth pressure of retaining wall. It was originally developed for gravity walls, which have rigid behavior, retaining cohesionless backfill materials. However, it is used for cantilever retaining wall on the various foundation conditions. Considering only inertial force of the soil wedge as a dynamic force in the M-O method, inertial force of the wall does not take into account the effect on the dynamic earth pressure. This paper presents the theoretical background for the calculation of the dynamic earth pressure of retaining wall during earthquakes, and the current research trends are organized. Besides, the discrepancies between real seismic behavior and M-O method for inverted T-shape retaining wall with 5.4m height subjected to earthquake motions were evaluated using dynamic centrifuge test. From previous studies, it was found that application point, distribution of dynamic earth pressure and M-O method are needed to be re-examined. Test results show that real behavior of retaining wall during an earthquake has a different phase between dynamic earth pressure and inertial force of retaining wall. Moreover, when bending moments of retaining wall reach maximum values, the measured earth pressures are lower than static earth pressures and it is considered due to inertial effects of retaining wall.

• Applied Biological Chemistry
• /
• v.32 no.4
• /
• pp.321-326
• /
• 1989

Nitrogen and phytate solubility of perilla seed flour were influenced by the following factors: pH, centrifugal force, temperature and the presence of salt. The nitrogen solubility of perilla seed flour was minimum$(17.1{\sim}18.0%)$ at the pH range of $(4.0{\sim}5.0)$ and maximum(92.3%) at pH 11.0, while phytate solubility was the highest(48.5%) at pH 4.8 and lowest(8.3%) at pH 11.0. The phytic acid content in the extract decreased with an increase in centrifugal force. However, the nitrogen content was not affected by centrifugal force. The solubility of nitrogen and phytate gradually increased as the temperature was increased from $5^{\circ}C$ to $60^{\circ}C$ The addition of calcium$(0{\sim}50mM)$ at pH 5.0 decreased the phytate solubility, but increased nitrogen solubility. The solubility of nitrogen and phytate of perilla seed protein isolate was gradually increased as pH raised further. The protein and phytate contents of the perilla seed protein isolate were 1.1 and 89.6%, respectively, compared to 5.0 and 60.1% for perilla seed flour.

• Journal of Sericultural and Entomological Science
• /
• v.51 no.2
• /
• pp.207-210
• /
• 2013

In this study, matured silkworm hemolymph was studied for inhibitory effect on melanin formation, tyrosinase activities. A matured silkworm hemolymph mass purification method was developed and some of suppressing melanin formation effects were investigated, too. As a result, the advanced purification method was higher in yield rate than existing one by 53%. A free radical scavenging activity of hemolymph was higher than sericin on the market($IC_{50}$, $202.9{\pm}33.1$) and lower than vitamin C($0.57{\pm}0.02$) by $6.4{\pm}0.3{\mu}g/m{\ell}$. An inhibitory effect on melanin synthesis was higher in hemolymph compared to Morus bark and arbutin by 9.15% and 11.56%, respectively. An inhibitory effect on tyrosinase activity was higher in hemolymph than Morus bark and lower than arbutin. Effect of hemolymph $45{\mu}g/m{\ell}$ on suppressing of tyrosinase was almost 90%. Thus, these results suggest that hemolymph of matured silkworm may have beneficial properties as a material for cosmetics.

• Food Science and Preservation
• /
• v.22 no.4
• /
• pp.559-566
• /
• 2015

The aim of this study was to develop an analytical method for determination of T-2 toxin and HT-2 toxin level in cereals and to survey their levels using LC-MS/MS. The T-2 and HT-2 toxins were simultaneously analyzed by electrospray ionization with a positive ion mode and multiple reaction monitoring (MRM) after filteration and immuno-affinity column clean-up. A matrix-matched standard calibration used for quantification and recoveries of T-2 and HT-3 toxins were in the range of $100.6{\pm}7.2%$ and $96.8{\pm}9.4%$, respectively. Limits of detection and quantification of T-2 and HT-2 toxins were estimated to be 0.5 and $1.5{\mu}g/kg$, respectively. Each repeatability (RSRr) of T-2 and HT-2 toxins was determined to be 0.9~6.0%, and 4.9~6.1%, respectively. Total 115 samples cereals were collected from 9 types of cereals for analysis. The positive percentages of T-2 and HT-2 toxins obtained from collected samples were found to be 72% and 80%, respectively. The contamination level of T-2 toxin and HT-2 toxin in cereals were $37.1{\mu}g/kg$, and $5.4{\mu}g/kg$, respectively. Therefore, this study suggests that the developed method could be an useful analytical method to determine the T-2 and HT-2 toxin level in cereals and the present data could be used as a reference to estimate the risk assessment.

• Membrane Journal
• /
• v.6 no.2
• /
• pp.86-95
• /
• 1996

Rotary disc ultrafiltration module(RDM) was developed for the separation of oil e$$\mu$sions. This module was devised to reduce the gel polarization phenomenon by decoupling the operation pressure and the surface velocity of solution in ultrafiltration(UF) processes. The rotary disc membrane consists of 3mm-thick ABS plate covered with UF membrane (UOP, U.S.A.). When the angular velocity($\omega$) was increased, the pure water flux was slightly decreased due to pressure drop caused by centrifugal force and slip flow at the surface of membrane. The pressure drop was proportional to the square of linear velocity(${\omega}r$). When the angular velocity was changed from 52.36rad/s to 2.62rad/s, the flux decline for 5% cutting oil in one-shaft RDM at $25^{\circ}C$ and 0.1MPa was 30.16%. In the lower concentrations, angular velocity tends to give less effect on the flux. Flux(J; $kg/m^{2} \cdot s$) in a rotating disc module is mainly a function of the bulk concentration($C_{B}$; %), the linear velocity(${\omega}r$; m/s) and the effective transmembrane pressure($\Delta P_{T}$ ; Pa). Using a modified resistance-in-series model, the flux data of cutting oil experiments were fitted to give the following equation.