• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.3
• /
• pp.91-96
• /
• 2019

There are so many low power MAC protocols for wireless sensor network. IEEE802.15.4 among them has disadvantage of a large power consumption for synchronization. To save power consumption it use the superframe operation alternating sleep mode and awake mode. But latency is longer result from superframe operation. Typical asynchronous B-MAC can have shorter latency according to check interval. But transmitter consumes more power because of long preamble. And receiver is suffering from overhearing. In this paper, we propose the adaptive check interval scheme of B-MAC for enhancing the power consumption and delay latency performance. Its power consumption is evaluated by comparing the proposed scheme with a typical IEEE802.15.4.

• Annual Conference of KIPS
• /
• 2021.05a
• /
• pp.104-107
• /
• 2021

전 세계적으로 건조한 지역이 늘어남에 따라 산불 발생 빈도가 증가하고 있다. 이에 대한 대안으로 센서를 이용한 산불 감지 시스템의 연구가 이루어지고 있다. 기존의 서버가 센서의 작동시간 설정값을 보내는 방식은 산불 발생 빈도가 높은 환경에서는 산불 감지가 늦어지고 산불 발생 빈도가 낮은 환경에서는 불필요한 산불 감지로 센서의 생명주기 낮아지는 비효율적인 면이 있다. 이에 본 논문에서는 센서 기반 산불 감지 시스템을 위한 향상된 센싱 주기 기법을 제안한다. 제안하는 센싱 주기 기법은 환경 요인, 센서의 작동시간 알고리즘을 이용하여 환경에 맞는 센서의 작동시간 설정값을 결정한다. 그 후 센서의 화재 감지 알고리즘을 통해 센서는 서버로부터 설정값을 받아 운용모드로 전환하여 화재상황이 났을 시에 서버로 메세지를 보낸 후 생명주기를 위해 저전력모드로 전환한다. 성능평가를 통해 기존의 방식보다 평균 18.1분 빠르게 화재상황을 감지할 수 있고 소모전력도 2.2mA만큼 낮았다. 향우 실제 화재환경에서의 성능평가가 필요하다.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2020.07a
• /
• pp.423-424
• /
• 2020

다양한 환경 변화에 따라 적용 가능한 최적의 위장무늬 개발의 필요성이 증대됨에 따라 위장무늬 성능 평가를 위한 포토시뮬레이션 기술 또한 주목받고 있으나 포토시뮬레이션 저작에 관한 연구는 미비하다. 본 논문에서는 작전환경 이미지 상 위장무늬 이미지의 배치 및 기 배치된 위장무늬의 탐지 시간을 측정하는 소프트웨어인 포토시뮬레이션 기술 개발에 대해 서술한다. 개발된 포토시뮬레이션은 작전환경 및 위장무늬 이미지 로드, 사용자 입력도구를 통한 대상 작전환경 이미지 상 위장무늬 이미지의 배치 및 저작, 저작 된 작전 환경 이미지 상 위장무늬 이미지를 모니터에 출력, 사용자 입력도구를 통한 작전환경 이미지 상 위장무늬 이미지의 탐지 및 탐지 시간 측정 기술을 포함한다. 결과에서는 개발 포토시뮬레이션 기술을 통한 위장무늬 이미지 배치 및 저작, 그리고 위장무늬 이미지의 평균 시간 측정 결과 예시를 보여준다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.6
• /
• pp.2381-2391
• /
• 2013

In general, ground's thermal properties, types of heat exchanger, operational method, thermal interference between piles can be considered as key factors which affect the thermal performance of energy pile. This study focused on the effect of these factors on the performance by a numerical model reflecting a real ground condition. Depending on the degree of saturation of ground, pile's heat transfer rate showed a maximum difference of three times, and the thermal resistance of pile made a maximum difference of 8.7%. As for the type of heat exchanger effects on thermal performance, thermal efficiency of 3U type energy pile had a higher value than those of W and U types. The periodic operation (8 hours operation, 16 hours pause) can preserve about 20% of heat efficiency compared to continuous operation, and hence it has an advantage of preventing the thermal accumulation phenomenon. Thermal interference effect in group piles may vary depending on the ground condition because the extent decreases as the ground condition varies from saturated to dry. The optimal separation distance that maintains the decreasing rate of heat efficiency less than 1% was suggested as 3.2D in U type, 3.6D in W type, and 3.7D in 3U type in a general ground condition.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.16 no.3
• /
• pp.249-258
• /
• 2010

This study seeks to improve NFRDI Serial Oceanographic observation (NSO) system which has been operated at current observation stations in the Korean Seas since 1961 and suggests the direction of NSO for practical use of Korean operational oceanographic system. For improvement, data handling by human after CTD (Conductivity-Temperature-Depth) observation on the deck, data transmission, data reception in the land station, and file storage into database need to be automated. Software development to execute QA/QC (Quality Assurance/Quality Control) of real-time oceanographic observation data and to transmit the data with conversion to appropriate format automatically will help to accomplish the automation. Inmarsat satellite telecommunication systems with which have already been equipped on board the current observation vessels can realize the real-time transmission of the data. For the near real-time data transmission, CDMA (Code Division Multiple Access) wireless telecommunication can provide efficient transmission in coastal area. Real-time QA/QC procedure after CTD observation will help to prevent errors which can be derived from various causes.

• Journal of the Korea Convergence Society
• /
• v.6 no.6
• /
• pp.285-291
• /
• 2015

FTMS, TCS, ITS equipment such as high-pass highway are just a situation that does not lack traceability and passive surveillance is related to fault DB has so far consisted of an integrated operations management to maximize utilization of the facility. In addition, there is no replacement parts are replaced when a failure occurs, increasing the number of parts and repair time I have trouble growing, and becoming a service interruption whenever you replace each time. In this study, proactively manage the failure history of a highway facility ITS tries to preventive maintenance. Therefore, the error history is based on the reliability of the high-pass facilities theory to calculate the reliability of the system through a systematic statistical analysis Operational Availability. The fault number and the time the replacement period through the estimate decreases and can reduce the budget expenses by securing the spare parts quantity, establish a management plan in part by improving the quality of the system through constant preventive maintenance, quality of service at all times It may direct the non-stop operation state of the available state.

• Korean Journal of Agricultural Science
• /
• v.11 no.2
• /
• pp.322-327
• /
• 1984

As a basic studies for the laboratory scale production of alfalfa inoculum, Rhizobium meliloti M14 was characterized for its carbon and nitrogen sources, and some parameters for broth cultivation in a chemostat were studied by semi-continuous operation. The result s obtained were as follows. 1. Growth rate of the strain was increased by disaccharides than by monosaccharides tested, and pentoses resulted in poor growth than hexoses. Sugar alcohols including inositol supported the best growth among sugars. 2. Mannitol in the yeast-mannitol-broth was substituted by natural carbon sources such as malt extract or molasses. 3. Ten per cent of fresh yeast water appeared to supply enough amount of growth factor s for the strain, and the effect was equivalent to 0.24 percent of the commercial yeast extract powder. 4. Batch growth of the stain in a chemostat, New Brunswick Micro Ferm 28L, reached in the early stationary growth phase of $5{\sim}7{\times}10^9cells/ml$ after 36 hours of incubation. The culture at this stage was switched to semi-continuous cultivation, and the culture broth of four-fifth of the working volume was recovered every 24 hours when the maximal count was obtained.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.10B
• /
• pp.1050-1061
• /
• 2009

The Tactical Internet(TI) managed by Infantry Brigades is used for the purpose of sharing information of Command Control and Situation Awareness. When there are more than two destinations to transmit data in the TI system, a multicasting is utilized based on pre-defined multicast groups. However even in the case when a source node needs to send some messages like weathercast and attack alarm etc to only a part of Battalion or Brigades in a specific geographical region (destination region), the current TI multicasting protocol is designed to transmit the messages to the pre-defined group or all of the Battalion/Brigade nodes, resulting in inefficiency in terms of end-to-end delay and overhead. In this paper, we propose more efficient protocol for such cases, named as "Tactical Internet Geocasting (TIG)". The proposed scheme firstly checks whether the destination region belongs to one Battalion region or more than two Battalion regions using location information, and then performs a greedy forwarding from the source node to the destination region, followed by a local flooding inside of the destination region. With performance analysis and simulations using NS-2, TIG is compared to the current TI multicasting protocol (i.e., Simplified MDP) and the LBM (Location-based Multicast). The simulation results show that the proposed TIG is more efficient than both in terms of delay and network overhead.

• Journal of Chest Surgery
• /
• v.31 no.9
• /
• pp.867-872
• /
• 1998

Background: The fixed dose regimen with activated coagulation time(ACT) is the most commonly employed method for determining the required dosage of heparin and protamine during cardiopulmonary bypass(CPB). Material and Method: We performed a prospective study on a fixed dose regimen for analyzing adequate dosages of heparin and protamine, the incidence of heparin resistance and heparin-induced thrombocyt openia, factors affecting ACT during CPB, and changes of ACT during aprotinin usage. 300 units/kg of heparin were administered to patients, and ACTs were measured after 5 mins. ACTs were checked at 10 mins and 30 mins after the onset of CPB, and then at 30 min intervals thereafter. If the measured ACT was under 400 secs, we added 100 units/kg of heparin. The heparin was reversed with 1 mg of protamine for each 100 units administered. If the measured ACT was longer than 130 secs 30 mins after protamine administration or if there was definitive evidence of a coagulation defect, we administered a further 0.5 mg/kg of protamine. Result: We studied 80 patients(50 adults and 30 children) who underwent open heart surgery(OHS) at Seoul National University Hospital. Preoperative ACT was 114.3${\pm}$19.3 secs in adults, and 119.5${\pm}$18.2 secs in children. There were no differences in preoperative ACT due to age, body weight, body surface area, or sex. The preoperative ACT was not influenced by a positive past history of OHS. Ten adults(20%) and 3 pediatric patients(10%) needed additional doses of heparin to maintain the ACT above 400 secs. Additional protamine administration was needed in 9 adults(18%) and 10 children(33%). Heparin resistance was found in only two adults. Heparin-induced thrombocytopenia was detected in 2 adults and 1 child. During CPB, ACT was prolonged. 12 adult patients received a low dose of aprotinin and showed longer celite activated ACT compared to the control group.The kaolin activated ACT showed a lower tendency than the celite activated ACT in aprotinin users. Conclusion: In conclusion, fixed dose regimen of heparin and protamine can be used without significant problems, but the incidence of need of additional dosage remains unsatisfactory.

• Bulletin of the Korean Space Science Society
• /
• 2009.10a
• /
• pp.37.3-37.3
• /
• 2009

태양물리연구실에서는 춘 추분기를 전후한 일정 기간 사이에 수분 정도 발생하는 태양간섭 현상을 예측하기 위하여 프로그램을 개발하였다. TU 미디어에서 제공해준 3개의 통신위성 PAS-8, TELSTAR-10, MEASAT-1에 대한 2006, 2007년도 춘 추분기의 통신장애 자료와 계산한 자료를 비교 분석하였고, 이를 이용하여 2009년도 추분기의 태양간섭 현상 시간을 예측하였다. 태양위치변화 계산은 NASA/JPL에서 발행하는 DE406 역서 자료를 이용하여 정밀도를 높였으며, 지구 타원체 모델을 통해 기지국에서의 정확한 태양 및 위성의 고도, 방위각을 구하였다. 또한 기지국 안테나 이득률을 계산하여 기지국 안테나에서 예상 되는 태양 간섭 시간을 얻어 냈다. 기지국 안테나의 빔 패턴은 안테나의 중심 부근에서 가장 강하게 나타나며, 중심에서 멀어질수록 특수한 감쇄 형태를 보인다. 이러한 빔 패턴은 안테나의 이득률과 관련이 있으며, 빔 패턴의 적분을 통해 얻어진 이득률과 태양 디스크가 얼마나 안테나의 범위에 들어오는가에 따라 안테나에 수신되는 전파의 강도가 달라진다. 이러한 강도 변화량을 계산함으로써 태양 간섭 시간을 계산할 수 있다. 본래 안테나 빔 패턴은 개개의 안테나에 따라 다르며 직접 측정하여 얻을 수 있다. 사용한 빔 패턴 모델은 ITU에서 채택된 WARC-79 모델을 이용하였고 모든 위성 기지국 안테나의 빔 패턴은 이 모델에서 벗어나지 않는다. 이 연구에서는 빔 패턴 모델을 적용하여 기존의 TU미디어 성수기지국에서의 태양간섭 시간을 다시 계산하였다. 또한 새롭게 KT 용인 위성 관제센터의 자료를 추가하여 태양 간섭시간을 계산하고 예측하였다. 위성데이터는 기존의 PAS-8, TELSTAR-10, MEASAT-1 통신위성과 KT에서 운용하고 있는 무궁화 3호와 무궁화 5호 통신위성 자료를 사용하였다. 이러한 계산 방법은 전국 임의의 지역에서 춘 추분기에 발생할 수 있는 태양간섭 시간을 예측하고 적용할 수 있다.