• Journal of the Korean Chemical Society
• /
• v.47 no.1
• /
• pp.19-25
• /
• 2003

A spectrophotometric method for the simultaneous determination of anionic and nonionic surfactant based on the application of multivariate calibration method such as principal component regression(PCR) and partial least squares(PLS) has been studied. The calibration models in PCR and PLS were obtained from the spectral data in the range of 400~700 nm for each standard of a calibration set of 26 standards, each containing different amounts of two surfactants. The relative standard error of prediction(RSEP$_{\alpha}$) was obtained to assess the model goodness in quantifying each analyte in a 5 validation samples which containing different amounts of two surfactants.

• Fire Science and Engineering
• /
• v.24 no.1
• /
• pp.122-127
• /
• 2010

The combustion characteristics of phenol foam were analysed using variable external irradiation level (20, 25, 35, 50, and $70kW/m^2$) and in the mixture gas of oxygen/nitrogen. The oxygen index were carried out from the oxygen index tester (KS M ISO 4589-2) and ignition time, critical heat flux, and mass loss rate were carried out from the mass loss calorimeter (ISO 5660-1). As the results of this study, the critical heat flux and average mass loss rate were $28.99kW/m^2$ and $0.56{\sim}1.77g/m^2s$ respectively at the variable external irradiation level. And the limited oxygen index were 45.1% in mixture gas of oxygen/nitrogen. In conclusion, we knew that phenol foam had the best performance than other foam materials in fire safety from all data of this study.

• Journal of Convergence for Information Technology
• /
• v.9 no.12
• /
• pp.147-156
• /
• 2019

Numerical study was performed to investigate the convective heat transfer of Al₂O₃/water nanofluid flowing through the concentric double pipe counterflow heat exchangers. Hot fluid flowing through the inner pipe transfers its heat to cooling fluid flowing in the outer pipe. Effects of important parameters such as hot and cold volume flow rates, fluid type in the outer and inner pipes, and nanoparticles concentration on the heat transfer and flow characteristics are investigated. The results indicated that the heat transfer performance increases with increasing the hot and cold volume flow rates, as well as the particle concentrations. When both outer and inner pipes are nanofluids with 8% nanoparticle volume concentration, nanofluids showed up to 17% better heat transfer rate than basic fluids. Also, the average heat transfer coefficient of the base fluid for annulus-side improved by 31%. Approximately 20% enhancement in the heat exchanger effectiveness can be achieved with the addition of 8% alumina particles in base fluid. But, addition of nanoparticles to the base fluid enhanced friction factor by about 196%.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.11A
• /
• pp.929-935
• /
• 2003

An analog/digital mixed mode ASIC for network synchronization of ATM switching system has been designed and fabricated. This ASIC generates a 234.7/46.94 ㎒ system clock and 77.76/19.44 ㎒ user clock using 46.94 ㎒ transmitted clocks from other systems. It also includes digital circuits for checking and selecting of the transmitted clocks. For effective ASIC design, full custom technique is used in 2 analog PLL circuits design, and standard cell based technique is used in digital circuit design. Resistors and capacitors for analog circuits are specially designed which can be fabricated in general CMOS technology, so the chip can be implemented in 0.8$\mu\textrm{m}$ digital CMOS technology with no expensive. Testing results show stable 234.7 ㎒ and 19.44 ㎒ clocks generation with each 4㎰ and 17㎰ of low ms jitter.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.1
• /
• pp.101-107
• /
• 2020

We propose a realistic seeing through visualization methods in mixed reality environment. When a user wants to see specific location beyond a wall in indoor environment. The proposed system recognizes and registers the selected area using environment modelling and feature-based tracking. Then the selected area is diminished and the specific location is visualized in real-time. With the proposed seeing through methods, a user can understand spatial relationship of the building and can easily find the target location. We conducted a user study comparing the seeing through method to conventional indoor navigation service in order to investigate the potential of the proposed seeing through method. The proposed seeing through method was evaluated in navigation time in comparison with conventional approach. The proposed method enable users to navigate target locations 30% faster than the conventional approach.

• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.15-20
• /
• 2002

We demonstrate a widely-tunable wavelength converter based on four-wave mixing in a semiconductor-fiber ring laser with no external pump light. Applying 10 GHz short pulses at -8 dBm as a probe signal, we achieve continuous wavelength tuning over the semiconductor optical amplifier gain-bandwidth reaching 30 nm down- and 17 m up-wavelength conversion. In addition to the wide tuning capability, the converter shows high-speed conversion and low saturation power capabilities.

• Journal of Advanced Navigation Technology
• /
• v.18 no.2
• /
• pp.151-157
• /
• 2014

Recently UAV(unmanned aerial vehicle) is frequently used not only for military purpose but also for civil purpose. UAV automatically navigates following the coordinates input in advance using GPS information. However it is impossible when GPS cannot be received because of jamming or external interference. In order to solve this problem, we propose a real-time segmentation and classification algorithm for the specific regions from UAV image in this paper. We use the super-pixels algorithm using graph-based image segmentation as a pre-processing stage for the feature extraction. We choose the most ideal model by analyzing various color models and mixture color models. Also, we use support vector machine for classification, which is one of the machine learning algorithms and can use small quantity of training data. 18 color and texture feature vectors are extracted from the UAV image, then 3 classes of regions; river, vinyl house, rice filed are classified in real-time through training and prediction processes.

• Journal of the Korean Institute of Gas
• /
• v.2 no.1
• /
• pp.23-27
• /
• 1998

To protect the underground pipeline from the mechanical damage and to enhance the cathodic protection effect, the river sand has been backfilled traditionally around the buried pipeline. However, river sand became depleted and expensive. One has to seek for the economic alternative materials. Crashed stone is a good candidate for the backfill material. In this study, how much the particle size and shape of the crashed stone can effect on the gas pipeline coating was examined. A series of laboratory and field test was performed. In the Lab, the increasing loads were applied to the coated pipeline surrounded by the crashed stone, where no significant damage was observed.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.11 no.2
• /
• pp.5-11
• /
• 1974

Theoretical analysis is carried out for the beat frequency generation phenomena in the IMPATT diodes an4 the experimental studies are given in parrallel. The theory is based on the space charge modulation effect introduced to the multiplication process by the input signal. Computed results show that the beat frequency output power is linearly dependent upon the signal power and self oscillating power. Also the strong dependence of the output power with respect to the diode negative resistance is found and it turns out that the larger the negative resistance, the stronger the beat frequency output power. Experimental results show a good agreement with the theoretical values. Calculated conversion gain is about -0.4[db] at 10[GHz] and the experimental value shows -6.2[db] below this value. This difference between the theoretical and the experimental values is considered to be the results of the ineffective injection of signal power.

• Journal of the Korean Institute of Gas
• /
• v.17 no.2
• /
• pp.50-58
• /
• 2013

Various process piping usually carries out high flammable and explosible gas under high pressure and high temperature. Due to frequent change of design and structure it becomes more complicated and compactly located. The safety management level is relatively low since it is considered as simply designed component. In this study a safety assessment procedure is proposed for complicated piping system around a mixing drum in which natural gas and by-product gases were mixed. According to ASME code, pipe stress analysis was conducted for determining design margin at some key locations of the piping. These high stress locations can be used as major inspection points for managing the pipe integrity. Sensitivity analysis with outside temperature of the pipe and support constraint condition. Possible effect of hydroen gas to the pipe steel during the previous use of the by-product gas was also discussed.