• Journal of the Korea Institute of Building Construction
• /
• v.11 no.3
• /
• pp.283-291
• /
• 2011

As the construction industry has recently been transformed by the emergence of ubiquitous and intelligent technology, there have been major changes in the management methods employed. Specifically, next-generation construction management systems have been developed that collect and analyze many pieces of information in real time by using various wireless sensors and networks. The purpose of this study is to understand the current status of Ubiquitous Sensor Networks (USN) in the construction sector, and to gain fundamental data for a system of measuring concrete curing temperature in a construction site that employs a USN. By investigating the application status of USN, it was confirmed that USN has mainly been applied to the maintenance of facilities, safety management, and quality control. In addition, a field experiment in which the curing temperature of concrete was measured using a USN was carried out to evaluate two systems with wireless sensor networks, and the applicability of these systems on site was confirmed. However, it is estimated that the embedded wireless sensor type is affected by metal equipment on site, internal battery of sensor and concrete depth, and studies to provide more stable system by USN are thus required.

• Journal of ILASS-Korea
• /
• v.23 no.4
• /
• pp.221-226
• /
• 2018

Despite the increasingly stringent automotive emissions regulations, the impact of vehicle emissions on air pollution remains large. In addition, since the issue of emission of more exhaust gas than the exhaust gas measured in the test room when the vehicle passing the exhaust gas regulation standard is run on the actual road, many countries studied and introduced gas regulations about Real Driving Emission using Portable Emission Measurement System. At present, Korea regulations restrict the number of NOx and PN in diesel vehicles. In the case of gasoline vehicles, there is no regulation on emission gas, but there is a problem of continuing automobile exhaust gas problems and a large amount of gasoline GDI vehicle's PN emission. So research and interest are increasing due to this problem. In this study, characteristics of exhaust gas depending on changes of ambient temperature were analyzed among various factors affecting exhaust gas measurement of gasoline vehicles. As a result, at the low temperature test, the lower the ambient temperature, the more the exhaust gas was emitted. At ordinary temperature test, no specific tendency was observed due to changes of ambient temperature.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.121-121
• /
• 2017

오늘날 시장에 유통되는 버섯은 대부분 환경이 조절되는 시설 내부에서 재배된다. 버섯은 다른 식물과 달리 버섯의 종류, 품종 등에 따라 요구되는 환경이 매우 다르다. 특히 대부분의 버섯은 버섯이 생육되는 공간의 온도, 수분, 이산화탄소, 조도 등의 관리가 필수적이다. 버섯의 단위면적당 생산량을 극대화하기 위해서는 이들 버섯이 필요로 하는 환경을 버섯의 생육특성에 따라 적합하게 유지해 주어야만 한다. 현재 대부분의 버섯재배사에는 이들 환경을 컨트롤하는 장치가 설치되어 있고, 이들 시스템의 환경 설정은 농업인이 현장에서 버섯의 상태를 확인 한 후 그때그때 경험에 의해 채득한 정보를 기반으로 환경설정을 하고 있는 실정이다. 이렇다 보니 버섯을 재배하는 기간에는 농업인이 재배사 내부의 환경을 관리하기 위해서 항상 버섯재배사에 머물러야 하고, 재배사의 환경관리 때문에 원거리 또는 장기 출타가 어려운 실정이다. 본 연구에서는 기존에 사람이 버섯재배 현장에서 컨트롤하던 환경관리를 원격에서 컴퓨터 또는 모바일로 구현할 수 있는 시스템을 개발하였다. 시스템에서 모니터링 및 제어하는 환경은 온도, 습도, 이산화탄소, 배기팬 및 입기팬의 가동 등 버섯재배 환경관리에 필요한 모든 요소를 모니터링 및 관리할 수 있도록 하였다. 이들 관리 요소는 인터넷이 연결된 컴퓨터에 접속하여 버섯재배사의 환경을 실시간으로 모니터링 하고 필요에 따라 제어를 할 수 있도록 하였다. 또한 컴퓨터에서 볼 수 있는 환경을 스마트폰을 통해서도 볼 수 있고 또한 제어할 수 있도록 하였다. 그리고 버섯배지를 입상 한 후부터 수확시기까지의 관리 환경을 데이터베이스로 만들어 농민이 버섯배지를 입상하고 데이터베이스와 연동한 제어가 되도록 설정하면 버섯재배사 내부의 환경은 데이터베이스의 정보를 읽어 들여 버섯의 생육단계에 따라 자동으로 내부환경이 제어되도록 하였다. 또한 농업인이 원격에서 버섯재배사 내부 버섯의 생육상황을 모니터링 할 수 있도록 재배사 상부에 CCD 카메라를 달아 실시간으로 버섯의 생육상활을 모니터링 할 수 있도록 구성하였다. 이와 같은 시스템을 사용하면 버섯재배 경험이 없는 농업인도 경험자와 같은 재배관리가 가능하고 원격에서 재배사 내부환경을 모니터링하고 제어 할 수 있기 때문에 농업인이 재배사에 매여 있지않아도 될 것으로 판단된다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.254-254
• /
• 2022

밭 용수관리 및 가뭄 대응을 위한 토양수분 실측자료의 품질관리가 필수적으로 수행되어야 한다. 토양수분 자료의 체계적인 유지관리를 위해 국제 토양수분 네트워크(International Soil Moisture Network; ISMN)가 설립되었고, 전세계 1,400여개 지점의 토양수분량 자료의 품질관리하고 있다. ISMN 품질관리 방식은 토양특성, 강우에 대한 반응, 토양온도, 시계열특성을 이용한다. 지표면 최상 토층에 저장되어있는 수분인 토양수분은 기후 예측, 홍수 예보, 농업가뭄평가, 수자원 관리, 온실가스 산정, 인프라 보전, 수인성 전염병 모델링 등 다양한 분야에 활용될 수 있다(Dorigo et al., 2011). 본 연구에서는 FDR(Frequency Domain Reflectometry) 기기를 이용한 토양수분 측정자료의 품질관리를 위해 ISMN에서 제시한 총6개의 단계별 품질관리 체계를 적용하였다. 단계는 1) 토양수분이 0 m3m-3보다 작은지, 2) 또는 0.6 m3m-3보다 큰지, 3) 토양수분값이 공극률보다 큰지, 4) 토양온도가 영하인지, 5) 토양수분이 강우 이벤트 없이 증가하는지, 그리고 5) 토양수분 시계열 자료에 spike 가 있는지 6) break나 plateau가 있는지를 검사하여 Quality Flag를 설정하였다. 이를 기반으로 토양수분 데이터 자동 프로그램을 개발하여 이상치를 보정하였다. 향후, ISMN의 Quality Flag (QF1-QF10)를 적용하여 모니터링 자료의 품질관리 자동 프로그램을 개발하고자 한다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.2
• /
• pp.185-191
• /
• 2003

This paper presents the thermal problems of steel-concrete composite structure and the basic references in placing concrete into the structure. Based on the analytical investigation, application of the composite structure has the effect of highly decreasing the temperature difference between the center section and the surface section of the structure, though its application has little influence on the decrement of the maximum temperature under the same using material and placing temperature. Meanwhile, its application causes the section decrement of a concrete structure, and in the section which the decrement ratio is relatively large, the restraint action by a old concrete structure takes place highly tensile stresses over a tensile strength. And, the stress is concentrated on sharp edges of the steel-concrete boundary. Both restraint action and stress concentration considerably decrease the reduction effect of the temperature difference. Therefore, the prediction of thermal response and the reasonable steps are required through the simulation considering the factors and the sections related to those problems.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.3
• /
• pp.69-74
• /
• 2018

Fiber-Reinforced Cementitious Composites (FRCCs) have electrical conductivity by inserting reinforced conductive fibers into a cementitious matrix. Such characteristic allows us to utilize FRCCs for crack monitoring of a structure by measuring electrical responses without sensor installation. However, the electrical responses are often sensitively altered by temperature variation as well as crack initiation. The temperature variation may disturb crack detection on the measured electrical responses. Moreover, as sensing probes for measuring electrical reponses increase, undesired contact noises are often augmented. In this paper, a self-sensing impedance circuit is specially designed for reducing the number of sensing probes. The crack initiation and temperature variation effects on the self-sensing impedance responses of FRCCs are experimentally investigated using the self-sensing impedance circuit. The experiment results reveal that the electrical impedance response are more sensitively changed due to temperature variation than crack initiation.

• Journal of Mushroom
• /
• v.9 no.3
• /
• pp.96-100
• /
• 2011

MST247ns(Hwaseong #2) was developed by the method of Di-mon mating between monokaryotic strains derived from "Hwaseong #1" and dikaryotic strain "Suhan #1". The optimum temperature of mycelial growth was $25-30^{\circ}C$. The optimum temperature of primordia formation and fruiting body development were $8-15^{\circ}C$ and $9-14^{\circ}C$. Days of primordia formation were 4-5 days later Suhan #1. The stipes were longer than "Suhan #1". The surfaces of stipe were white and the tissues got harder and more elastic. Therefore, the management of growth environment under low temperatures was relatively easy and storability got much better.

• Journal of the Korea Society of Computer and Information
• /
• v.12 no.5
• /
• pp.321-326
• /
• 2007

The contents of reef container face a risk of being damaged if the interior temperature and certain maintenance conditions for the shipments cannot be met. Currently, the temperature and other conditions within a reefer container is checked manually and periodically by someone in charge of it. Since it means that there is no real-time checking of the conditions, if something goes wrong, there is no immediate means of correcting the problem. This paper introduces reefer container monitoring system, that checks interior temperature of container on real-time by sensor nodes attaching reefer container using wireless sensor network. It senses the temperature, amount of light, motion and the change in speed of the objects that distributes sensors throughout the desired places and sends the data wirelessly to anyone interested. Because the prosed technique can check the temperature and other conditions within a reefer container on real-time basis, it enables efficient and effective maintenance of temperature and other conditions

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.231-234
• /
• 2011

Recently, the smart RFID tag technology which can measure external changing environment is globally interesting. In this paper, development of the Smart RFID tag using temperature sensor was represented. Smart RFID tag is basically comprised of antenna which has its bandwidth of 13.56Mhz, temperature sensors and data processing controller. Antenna design and smaller PCB production can be used to agri-food wrap. Since the smart RFID tag is distributed as an attachment to agri-food wrap, consumer can check temperature changes in the distribution process. Because temperature change check in real time, food confirm the status of transportation and the freshness. Also, smart RFID tag can be applied to proposed smart refrigerator.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.4 s.56
• /
• pp.159-169
• /
• 2009

In this study, static loading tests and numerical analyses of the composite beam strengthened by multi-stepwise thermal prestressing method were carried out to evaluate the prestressing effect of the thermal prestressing prestress and the sectional effect of the installed cover-plate on the increase in the load-carrying capacity of composit beam. From this study, the strengthening method using multi-stepwise thermal prestressing method (TPSM) can be applied to reduce the deflection of the composite beam as well as to strengthening the composite beam by inducing the prestress in case of the occurrence in the large deflection by the insufficiency of the section properties of the composite beam. because of the expectation of the increase in the yield load and the sectional properties of the composite beam.