• Fire Science and Engineering
• /
• v.17 no.3
• /
• pp.26-30
• /
• 2003

This paper presents a study on the analysis for false alarm of heat detector using HRR(Heat Release Rate). And it is represented to threshold value and domain of false alarm. The HRR threshold value of false alarm is calculated to use parameters obtained by small scale fire-experiment. The experiment is conducted to measure detector activation time and flame spread of wood cribs fire, etc. The results show that HRR threshold value of Fixed type detector is 20.24 kW and rate of rise type detector is 13.59 kW, respectively.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.5
• /
• pp.177-187
• /
• 1998

최근 국내에서 해양 구조물, 장대 교량의 하부구조물, LNG저장탱크 등 매스콘크리트의 증가추세에 따라 구조물의 고내구성과 관련하여 시멘트의수화열에 의한 온도균열의 발생을 최소화 시킬 수 있는 3성분계 혼합형 저발열시멘트가 개발되어 실 구조물의 적용단계에 있으나, 저발열시멘트가 개발되어 실 구조물의 적용단계에 있으나 저발열시멘트의 특성에 대한 전반적인 연구보고가 국내에서는 미진한 실정이다. 따라서 본 연구에서는 3성분계 혼합형 저발열시멘트의 특성 및 코\ulcorner리트의기초물성을 1종 보통포틀랜트 시멘트, 5종 내황산염시멘트, 슬래그시멘트와 비교하였다. 글 결과 저발열 콘크리트의 찹축강도는 초기재령에서 강도발현률이 적은 반면 장기강도발현률은 상당히 큰 경향을 보였다. 또한 수화열은 1종시멘트를 사용한 콘크리트에 비하여 1/3~1/2정도로 매스콘크리트의 수화열을 대폭적으로 저감시킬 수 있을 뿐만 아니라 염소이온에 대한 저항성이 상대적으로 높게 나타나 거대 해양 구조물의 적용에 매우 유리한 시멘트로 판단되었다.

• Nuclear Engineering and Technology
• /
• v.5 no.4
• /
• pp.291-309
• /
• 1973

Exposure rates due to leakage gamma-rays from operating reactors TRIGA Mark II and III were measured in a horizontal plane by means of scintillation spectrometry using a 3"$\times$3" cylindrical Nal(T1) detector associated with a 400 channel pulse height analyzer under varied conditions of reactor operation. In determining exposure rate due to the leakage gamma-rays at each point of measurement, Moriuchi's spectrum-exposure rate conversion theory was applied instead of using conventional responce matrix method which necessitates very complicated procedures to convert a spectrum into exposure rate. The results show that a basic pattern of "typical" spectrum of the reactor leakage gamma-rays is neither affected by thermal output of the reactor, nor influenced by overall attenuation in radiation intensity. It was indicated that he attenuation of the leakage gamma-rays in air in terms of exposure rate as a whole follows an exponential law, and the total exposure rate due to the leakage gamma-rays at a certain point is nearly proportional to thermal output of the reactor. The complexity in spectrum measured for a movable core reactor, TRIGA Mark III, was analyzed through spectrum resolution, and proper judgement of the leakage gamma-rays in a complex spectrum was discussed.ctrum was discussed.

• Tunnel and Underground Space
• /
• v.23 no.5
• /
• pp.442-453
• /
• 2013

A large-scale high-temperature thermal energy storage(TES) was numerically modeled and the heat loss through storage tank walls was analyzed using a commercial code, FLAC3D. The operations of rock cavern type and above-ground type thermal energy storages with identical operating condition were simulated for a period of five consecutive years, in which it was assumed that the dominant heat transfer mechanism would be conduction in massive rock for the former and convection in the atmosphere for the latter. The variation of storage temperature resulting from periodic charging and discharging of thermal energy was considered in each simulation, and the effect of insulation thickness on the characteristics of heat loss was also examined. A comparison of the simulation results of different storage models presented that the heat loss rate of above-ground type TES was maintained constant over the operation period, while that of rock cavern type TES decreased rapidly in the early operation stage and tended to converge towards a certain value. The decrease in heat loss rate of rock cavern type TES can be attributed to the reduction in heat flux through storage tank walls followed by increase in surrounding rock mass temperature. The amount of cumulative heat loss from rock cavern type TES over a period of five-year operation was 72.7% of that from above-ground type TES. The heat loss rate of rock cavern type obtained in long-period operation showed less sensitive variations to insulation thickness than that of above-ground type TES.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.4
• /
• pp.313-319
• /
• 2017

Fiber optics sensors that have been mainly applied to aerospace areas are now finding applicability in other areas, such as transportation, including railways. Among the sensors, the fiber Bragg grating (FBG) sensors have led to a steep increase due to their properties of absolute measurement and multiplexing capability. Generally, the FBG sensors adhere to structures and sensing modules using adhesives such as an epoxy. However, the measurement errors that occurred when the FBG sensors were used in a long-term application, where they were exposed to environmental thermal load, required calibration. For this reason, the thermal curing of adhesives needs to be investigated to enhance the reliability of the FBG sensor system. This can be done at room temperature through cyclic thermal load tests using four types of specimens. From the test results, it is confirmed that residual compressive strain occurs to the FBG sensors due to an initial cyclic thermal load. In conclusion, signals of the FBG sensors need to be stabilized for applying them to a long-term SHM.

• Korean Chemical Engineering Research
• /
• v.50 no.6
• /
• pp.1034-1042
• /
• 2012

This study was performed by using an LFR (laminar flow reactor), which can be used to carry out different types of research on coal. In this study, an LFR was used to analyze coal flames, tar and soot yields, and structures of chars for two coals depending on their volatile content. The results show that the volatile content and oxygen concentration have a significant effect on the length and width of the soot cloud and that the length and width of the cloud under combustion conditions are less than those under a pyrolysis atmosphere. At sampling heights until 50 mm, the tar and soot yields of Berau (sub-bituminous) coal, which contains a large amount of volatile matter, are less than those of Glencore A.P. (bituminous) coal because tar is oxidized by the intrinsic oxygen component of coal and by radicals such as OH-. On the other hand, at sampling heights above 50 mm, the tar and soot yields of Berau coal are higher than those of Glencore A.P. coal by reacted residual volatile matter, tar and light gas in char and flame. With above results, it is confirmed that the volatile matter content and the intrinsic oxygen component in a coal are significant parameters for length and width of the soot cloud and yields of the soot. In addition, the B.E.T. results and the images of samples (SEM) obtained from the particle separation system of the sampling probe support the above results pertaining to the yields; the results also confirm the pore development on the char surface caused by devolatilization.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.127-130
• /
• 2002

본 연구에서는 우리말 연속 숫자음 인식에서 본래의 숫자음을 변이 시키는 주된 요인인 연음현상에 대한 인식을 높이기 위해 별도의 연음부분의 레퍼런스를 작성하여 매칭 시키는 방식을 제안한다 또한 단모음으로 이루어진 /2/와 /5/의 연속된 음에 대하여도 레퍼런스를 작성하였다. 제안한 방식에 의하여 전체적으로 $1.4\%$정도 인식률이 상승됨을 볼 수 있다. 특히 발성 목록중 /82/, /62/, /31/, /15/, /75/ 등의 연음과 /226/, /755/등과 같이 모음의 연속된 발성이 포함된 숫자 열에서 제안된 방식이 인식률에 영향을 미치는 것을 볼 수가 있었다. 이는 연음에서 발생하는 오류가 연속 숫자음에 많은 영향을 미치는 것을 알 수 있다. 그 외에 /22/, /55/등과 같이 단모음으로 이루어진 숫자음의 연속 발성 또한 인식률을 저하시키는데 한 요인으로 작용함으로서 이에 대한 레퍼런스도 작성하여 인식률이 상승되는 것을 볼 수 있었다.

• Journal of Practical Engineering Education
• /
• v.13 no.3
• /
• pp.497-505
• /
• 2021

Test equipment for strain and vibration measurement was designed for educational purposes. Widely available and affordable materials were put into making this device. Three strain gauges placed on an iron ruler made cantilevered beam were used to measure values according to external load. An electromagnet triggered excitation and a function generator created vibration of the beam. We present three different tests conducted with this equipment regarding production of scales, measurement of resonant frequency, and calculation of the difference between excitation frequency and measured frequency. Overall, this paper presents a piece of simple yet inexpensive test equipment and its corresponding portfolio with expectations of being applied to the educational field for efficient measurement of load and vibration.

• Communications for Statistical Applications and Methods
• /
• v.16 no.5
• /
• pp.803-812
• /
• 2009

The application of extreme value theory to financial data is a fairly recent innovation. The classical annual maximum method is to fit the generalized extreme value distribution to the annual maxima of a data series. An alterative modern method, the so-called threshold method, is to fit the generalized Pareto distribution to the excesses over a high threshold from the data series. A more substantial variant is to take the point-process viewpoint of high-level exceedances. That is, the exceedance times and excess values of a high threshold are viewed as a two-dimensional point process whose limiting form is a non-homogeneous Poisson process. In this paper, we apply the two-dimensional non-homogeneous Poisson process model to daily losses, daily negative log-returns, in the data series of KBW/USD exchange rate, collected from January 4th, 1982 until December 31 st, 2008. The main question is how to estimate extreme quantiles of losses such as the 10-year or 50-year return level.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.249-249
• /
• 2010

핵융합로에서는 디버터의 열부하에 대한 안전성을 고려하기 위해 열전도도 및 열 저항성이 높은 텅스텐이 대면 물질로 고려되고 있으며, 경제적인 측면과 실용성 측면에서 텅스텐블록을 직접 제작하여 사용하는 것보다 텅스텐코팅이 효과적이라는 의견이 지배적이다. 또한 ASDEX Upgrade 에서는 탄소블럭에 텅스텐을 코팅하여 챔버 외벽 및 디버터 영역까지 구성하여 캠페인을 진행하였고, 재료적인 측면에서 안정성을 확인 하였다. 따라서 본 연구에서는 디버터 및 챔버외벽 등에 대한 대면물질을 구성하기 위해 상압 열플라즈마 제트를 이용하여 고온에서의 용융 및 냉각을 통해 모재에 텅스텐 피막을 적층하는 과정을 수행하고 있다. 기존의 연구를 통해 일부 공정 변수에 대해서는 이미 적정한 범위의 공정조건을 확보하였고, 기공도와 산화도 및 부착력 등의 물성치에 대한 추가적인 향상을 위해 주요 공정 변수에 집중하여 최적의 조건을 탐색하는 과정이 진행 중이다. 이를 위해 출력증가실험의 일환으로서 기존 36kW급 플라즈마 토치 전력을 한 단계 끌어 올려 48kW급 전력까지 단계적으로 상승시킴으로써 이에 따른 물성치 변화를 검증하고 있다. 현재 44kW 급까지 실험이 수행되었으며, 이를 통해 공극률 감소 및 미세구조 변화에 대한 결과를 얻었다. 실제로 토치의 출력을 증가시킴으로서 텅스텐 피막의 물성치가 변화하는 메커니즘은 플라즈마 제트의 중심부 온도 및 축방향 속도에 의해 결정된다. 중심부 온도가 상승하게 될수록 코팅을 위해 분사되는 분말의 용융률은 증가하지만 분말 외벽에 산화텅스텐이 형성될 가능성은 증가하게 되며, 플라즈마 제트의 모재를 향상 축방향 속도가 증가할수록 용융 된 분말이 모재에 증착 시 형성하는 형태가 원형에 가깝게 되므로 기공이 감소하는 효과가 발생한다. 특히 용융된 분말의 증착 형태는 모재의 온도 및 분말의 입사속도에 결정적이 영향을 받게 되며, 결국 모재와 분말사이의 습윤성에 의한 분말 분산속도가 분말의 입사속도에 버금갈 경우 분말은 모재 위에서 효과적으로 원형으로 전이하며 적층하게 된다. 이러한 전이 현상은 앞에서 언급한 모재의 온도 등에 의해 결정적으로 영향을 받게 되며, 모재의 온도가 전이온도 이하일 경우 폭파형태에서 원형으로 분말의 증착 형태가 전이하게 된다. 이외에 추가적으로 진행하고 있는 연구는 코팅 전처리에 해당하는 분말 효과이며, 특히 탄화텅스텐 분말을 통한 재료적 auto-shroud 효과와 미세분말을 이용한 분말 표면열속의 증가에 따른 용융률 증가효과를 연구에 포함할 계획이다. 이러한 연구는 열적, 그리고 재료적 해석을 바탕으로 해석적 접근을 통해 이루어진다.