• Membrane Journal
• /
• v.19 no.1
• /
• pp.19-24
• /
• 2009

Sol-gel process is relatively simple, easy to use, cheap to install, and results in thin coating layers with superior physical and gas barrier properties. Films coated by the sol-gel process can be used as insulating films or packaging films for foods, chemicals, drugs, and beverages, etc. In this study, alumina sol was synthesized from aluminum isopropoxide and silane coupling agent was added to make coating solutions. In addition, biaxially oriented polypropylene (BOPP) was coated using several alumina sol solutions and their oxygen permeabilities were measured. The experimental results indicate that in the best case, the oxygen permeability of coated film was reduced by 85% compared to that of pure BOPP.

• Current Research on Agriculture and Life Sciences
• /
• v.27
• /
• pp.53-58
• /
• 2009

This experiment was conducted to determine the amount of asparagine content in soybean sprout soup as well as its effect on the regulation of blood alcohol concentration in human body. Asparagine content and alcohol concentration in blood were analyzed using the amino-acid analyzer and alcohol tester, respectively. Asparagine content in soybean sprout soup was highly significantly different among sprout soups sampled from different restaurants, although the boiling time and amount of sprout used were different among the samples. Significantly higher asparagine content was observed in soups with higher amounts of sprouts (2.81% in 500 grams of sprout) and 10 minutes after boiling with other solid ingredients in the soup. Lower concentration of alcohol in blood was recorded in persons with higher body weight. The asparagine+soybean extract (eaten immediately after drink) lowered the blood alcohol concentration significantly followed by only asparagine and control. The blood alcohol concentration after drinking become zero earlier (by 30 minutes), when asparagine+soybean extract or only asparagine was consumed as compared to control.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.6
• /
• pp.138-146
• /
• 2003

This paper deals with the experimental results that apply to a new wire by an artificial flame-maker because it's difficult to directly analyze the characteristic of deterioration by a forest fire. Those results include tension load, extension rate and torsion number for a conductor. In addition, there's been an experiment and analysis about the mechanical characteristics of the wire of ACSR 480$\textrm{mm}^2$ which was removed from Pohang area by a forest fire. Then, the database will be made to predict the state of deteriorated wires by a forest fire using those two data, and data necessary to diagnose the life state of an ACSR wire affected by a forest fire will be given.

• Journal of Power System Engineering
• /
• v.12 no.3
• /
• pp.55-59
• /
• 2008

In this paper, we have investigated on collection efficiency of fine particle of glass fiber-filter bag according to the surface treatment. The solution consisted of polytetrafluoroethylene(teflon), graphite powder, silicon resin and water was used as a basic surface treatment agent. Tensile strength of glass filter-bag increased with up to 3hrs and then decreased with surface treatment time. Tensile strength and initial modulus of the glass fiber-filter bag treated by iodine after basic surface treatment for 3hrs were lower than those of basic surface treatment for 3hrs, however collection efficiency and fracture strain were higher than those of basic surface treatment for 3hrs. Glass fiber-filter bag with lower initial modulus and more strain will be extend the durable period and the one treated by iodine after basic surface treatment 3or 3hrs is expected high collection efficiency of fine particle. This method makes it possible to manufacture glass fiber-filter bag of the optimum condition.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2006.05a
• /
• pp.53-54
• /
• 2006

Recently with increasing interest in the operation of life cycle, building remodeling business is spreading like a fashion. Keeping pace with the trend, the present project carried out the remodeling of an existing neighborhood facility into a religious facility based on the concepts of remodeling, reform and renovation. Basic requirements were overcoming spatial limitations, solving structural problems, meeting various functional needs, and securing a spatial size, and the project designed the interior of the building according to these requirements suggested by the owner. To overcome the low floor height of the existing space, the main sanctuary on the 1st floor had the ceiling in the form of a slant and installed indirect lighting into the resulting gaps, maximizing the depth and width of the space visually. The subsidiary sanctuary on the first basement was finished with red bricks, forming an arch using the bricks, to create religious atmosphere. However, considering the low floor height as in the 1st floor and the ceiling even lowered by the arch structure, the arch was formed threefold and the radius of the curvature of the arch was enlarged to secure a spacious feeling. The outer appearance was finished with granite on existing structure to save the cost of construction. In addition to the use of the finishing material, the structure of the arch and the frame of the opening part and the finishing of the walls were expressed with uneven surface in order to avoid the plainness of the appearance.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.3
• /
• pp.74-80
• /
• 2005

Steel plates used for common structures are manufactured by rolling processes in general. The rolling direction traces generated during the processes have significant influences on mechanical properties and fatigue behavior of the plates. The objective of present study is to investigate those directional characteristics for the enhancement of steel structure safety. SS400 steel plates of 3 mm thickness are tested in this study, When the angles between the tensile loading direction and the rolling direction of the plates are increased, their yield strengths are increased and elongations are rather decreased. It is also shown that fatigue crack growth rates in the plates can be increased according to the changes of those mechanical characteristics. For the safety of the structures, therefore, it is critical to decrease the angles between the rolling direction and the tensile loading direction.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.13 no.1 s.29
• /
• pp.43-47
• /
• 1989

The microstructural changes of nylon 6 UDY, POY and FDY were compared after free-annealing through crystallinity, birefringence, and melting behavior analyses. Free-annealing was done at various temperatures $(120^{\circ}C\;,140^{\circ}C,\;160^{\circ}C,\;180^{\circ}C,\;200^{\circ}C)$ and times (15 min., 30 min., 60 min.) using vaccum oven. Crystallinity was measured by the density gradient column technique and birefringence was measured using a Nikon polarizing microscope with a quartz wedge and Senarmont compensator. Melting behavior was investigated on the basis of DSC melting corves. Crystallinites of specimens increased as the treatment temperature and time increased. Birefringence of UDY increased after annealing and increased as the treatment temperature increased. On the other hand, those of POY and FDY decreased after annealing. Especially, the changes of crystallinity and birefringence of treated POY were particularly lower than those of treated UDY and FDY. Melting peaks of untreated UDY, POY and FDY were different in the position and the shape, but little change was seen in melting peaks in spite of increasing the annealing temperature and time. UDY and FDY showed single melting peaks in all the specimens. But POY showed double melting peaks, which means the coexistences of crystals with different thermal properties.

• Textile Coloration and Finishing
• /
• v.12 no.2
• /
• pp.103-110
• /
• 2000

To examine the physical properties of POY through the microstructure control, the crystal structure such as the crystallinity, the crystallite size, the orientation, the shrinkage, the tensile properties, and the thermal stress of POY(80/48, SD) were examined at different draw ratios and annealing temperatures. From the examination following conclusions were obtained : 1. The crystallinity was more effected by the heat setting temperature than by the draw ratio. The increasing rate was greatest at the heat setting temperature range of $170~190^\circ{C}$. 2. The crystallite size perpendicular to the fiber axis was more effected by the annealing temperature at lower draw ratios. On the other hand, the crystal and amorphous orientations were more effected by the heat setting at higher draw ratios. 3. The boiling shrinkage did not change significantly, but the total shrinkage showed 13% at the draw ratio 1.9 and the heat setting temperature $170^\circ{C}$. 4. The maximum thermal stress increased with increasing the draw ratio and decreasing the heat setting temperature in the temperature range of $170~210^\circ{C}$. At the draw ratio 1.9 and the heat setting temperature $170^\circ{C}$, the maximum thermal stress found was 1.1gf/d. 5. In the heat setting temperature above $170^\circ{C}$ after the drawing, the crystallinity, the crystallite size, the orientation, and the strength increased with increasing temperature, but the shrinkage and the maximum thermal stress decreased with increasing temperature.

• Textile Coloration and Finishing
• /
• v.28 no.1
• /
• pp.33-39
• /
• 2016

The crystal structure of nylon 56 fibers post extended by drawing process was investigated by synchrotron x-ray scattering measurement. In as-cast fiber, distinct (004) and (020) diffraction peaks were observed and they were related to initial metastable alignment of nylon molecules. With increase in the drawing ratio, (110) peak intensity was increased in vertical direction with decreasing (020) peak. At the same time, (004)' peak evolved position tilted to 29 degrees from the (004) peak. This evolution is directly related to stable crystalline phase of nylon 56 originated from additional formation of hydrogen bondings between N-H and C=O by post drawing process. We also compared density variation, stress-strain curves of the fiber as a function of drawing ratio and strain. The variations of density and tanacity also supported the increase of stable structure of nylon 56.

• Journal of the Korean Society of Industry Convergence
• /
• v.2 no.1
• /
• pp.27-33
• /
• 1999

Effects of spinning speed and draw ratio on structure and mechanical properties of PP filament. A The crystalline structure and mechanical properties of uniaxially deformed polypropylene filament has been examined by XRD, birefringence, UTM and density method. Uniaxially deformed PP filament was prepared of various spinning speeds (300, 600, 900m/min.) and draw ratio(x2, x3, x4). From the results of these studies, it found the following facts. Firstly, it was found that the crystallinity and crystallite size (110plane) of the samples were increased with increasing of spinning speed and draw ratio, especially, it was rapidly increased between as spun yarn and 2 times draw ratio. Secondly, birefringence value was increased with increasing of spinning speed and draw ratio. The mechanical properties of initial modulus, tensile strength were increased with increasing of spinning speed and draw ratio also, but the degree of elongation decreased as spinning speed and draw ratio.