• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.125-130
• /
• 2017

Automotive materials and plant modules need to be prepared for freezing parts to operate in extreme areas such as Eastern Europe, Russia, and Canada. However, the only thing that has been done for ultra-qualifying materials for extremely low operating materials is that only the effects at low temperatures are conducted at room temperature, and the effects at low temperatures are only identified at low speeds. Therefore, this study examined the low-temperature characteristics of materials by conducting comparative tests on the mechanical properties of the room at the temperature and temperature of TP304 and TP316 materials, which are the most common materials.

• Korean Journal of Materials Research
• /
• v.4 no.5
• /
• pp.556-565
• /
• 1994

Effects of Ag addition to 2090 and CP 276 Al-Li alloy systems on the microstructure and mechanical properties have been investigated. The addition of silver up to 0.16wt.% reduced the grain size of the alloys, and was responsible for the formation of finer and more uniform $\delta$'($AI_{3}Li$) and $T_{1}(AI_{2}CuLi$) precipitates in 2090 alloys, even though no variation of precipitates was found in CP 276 alloys. The addition of 0.16wt.% Ag improved the tensile strength of 2090 alloys about 40MPa with the expense of small reduction of percent elongation. However, the small addition of Ag to CP 276 containing Mg did not show any variation of tensile strength and elongation. The aging treatment of these alloys at $150^{\circ}C$ for 70 or 90 hours, depending on alloy systems, showed peak hardness value of about 92 $H_rB$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.13-19
• /
• 2018

Effects of multiwall carbon nanotube (MWCNT) type and flow type (shear and elongational flow) on the electrical conductivity of polycarbonate (PC)/ MWCNT nanocomposites were investigated. Two different MWCNTs produced a huge difference in electrical conductivity in an injection molded PC/MWCNT nanocomposite. It was observed that MWCNTs having a higher aspect ratio provide much lower electrical conductivity in injection molded PC/MWCNT nanocomposites while the conductivities of compression molded samples from two different MWCNTs were the same. We found that this is due to a difference in the deformability of the two MWCNTs. As the aspect ratio of the MWCNT increases, the orientation of MWCNT by the external force becomes easier and the conductive path diminishes. Consequently the conductivity of the nanocomposites decreases. Nanocomposite samples prepared at a higher extensional rate and shear rate showed lower electrical conductivity. This is also attributed to the flow induced orientation and reduced conductive path of the MWCNTs. The experimental results were discussed in relation to variation in the tube-tube contact due to the change of the MWCNT orientation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1521-1528
• /
• 2011

We studied the material properties for reliability improvement in finite element analysis results for a nitrile butadiene rubber hub-bearing seal and for a carbon-filled rubber mount used in a vehicle. It was difficult to measure the material properties of hundreds of types of rubber for the mount design. Thus, we suggested that the engineering stressstrain relations from pure shear test data could be synthesized by using simple tension data and Poisson's ratio. We defined Poisson's ratio by using a function of principal stretches to synthesize the stress-strain relations for a pure shear test. A transformation of the pure shear data was applied to the experimental values to obtain the predicted results when the strain approaches 100%. In the finite element analysis for the contact force of a hub-bearing seal, the strain results that used the transformation of the pure shear data and simple tension data almost corresponded to the experimental values. Ogden constants were used to analyze.

• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.458-466
• /
• 2011

In the mixed system of supercritical carbon dioxide/organic solvents, poly(vinyl alcohol)(PVA) film of high degree of hydrolysis could be dyed with a dichroic dye of C. I. direct black 22(DB22) and as a result, high durability was obtained. Especially, as a dye dispersant in a supercritical fluid phase, a mixed solvent system of ethylene glycol: dimethyl sulfoxide=4 : 6 weight ratio was investigated. Then the optimum pressure for dyeing could be reduced down to 200 bar. Using this supercritical fluid system, the maximum dyeing appeared as the transmittance of less than 1% and the waste amount was reduced to the level of 1/10. After 500% drawing of this PVA film, both the polarizing efficiency of 94% and the single piece transmittance of 30% were obtained. The limitation of DB22 and further improvements were also discussed.

• Polymer(Korea)
• /
• v.36 no.5
• /
• pp.606-611
• /
• 2012

Polyetherimide (PEI) and poly(vinylidene fluoride) (PVdF) blend web was prepared by electrospinning technique. In order to improve low mechanical properties, post processes like hot-pressing and heat-stretching were employed, and a study on the effects of post processes on their mechanical properties was performed. To confirm the physical properties of the web, scanning electron microscopy and tensile measuring instrument were used. The mechanical strength of webs pressed in the ratios of 1/2, 1/3, 1/4 and 1/5 at $180^{\circ}C$ were improved four-to-five times compared to pristine webs. Also they showed an additional increase by 2~8MPa, by heat-stretching 30 to 40% at $220^{\circ}C$.

• Polymer(Korea)
• /
• v.37 no.2
• /
• pp.249-253
• /
• 2013

From poly(lactic acid) (PLA) and poly(propylene carbonate) (PPC) synthesized using $CO_2$, a PLA/PPC/PLA layered film is prepared by coextrusion and then stretched to uniaxial orientation. The mechanical, optical, and barrier properties and shrinkage of the prepared film were investigated in detail. The maximum shrinkage of PLA/PPC/PLA film reached to 60% at $75^{\circ}C$. With increasing PPC content, the ratio of shrinkage of the film was increased and its shrinkagerate was increased. The ratio of shrinkage of the film decreased with increasing stretching temperature. The prepared film has oxygen and vapor transmission barrier properties. In this study, the PLA/PPC/PLA film is expected to be commercialized as a environmentally friendly shrinkable film.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1999.05a
• /
• pp.102-102
• /
• 1999

6Mo급 슈퍼 스테인리스강의 내식성은 여러 환경에서 여러 가지의 부식 시험 방법을 통해서 확띤되어 왔다. 이 합금이 보이는 탁월한 내식성 때문에 해수 설비 계통,정유 설비,원자력 발전소의 열교환기 등의 중요 재료로서 그 사용 용도가 급격히 증가하고 있다. 그런데 방사선의 영향을 받게 되는 설비에 금속 재료가 사용되는 경우,특히 경수로의 노내 구조물, 액체 금속로의 열교환기, 핵융합로의 제1벽 재료 등 에서는 합금 원소가 방사성 환경에 의하여 제거되는 현상이 나타난다. 따라서 본 연구에서는 이러한 상황을 미리 재료 제조 차원에서 모사하여 탄소량과 질소량의 함량 을 달리 한 6Mo급 슈퍼 스테인리스강을 제조하여 미세 조직, 기계적 성질 및 부식 특성의 변화에 대하여 연구하였다. 진공 고주파 유도 용해로를 이용하여 탄소량과 질소량이 각기 변화된 슈퍼 스테인리스강을 용해 한 뒤 아르곤 가스 분위기에서 $1180^{\circ}C$로 soaking하고 열간 압연을 행하였다. 열간 압연으로 표변에 생성된 산화 스케일을 불산과 질산의 혼합 용액으로 제거한 뒤 냉간 압연을 행하였다. 이 냉연 판재에 대하여 $1150^{\circ}C$로 소둔하여 각 실험에 사용하였다. 광학 현미경을 이용하여 미세 조직의 변화를 관찰하였으며, 상온과 고온($520^{\circ}C$)에서 인장 시험을 행하였으며, 경도 측정을 행하였다. 또한 양극 분극 시험과 비등 질산 침지 시험 및 비등 40% NaOH 용액에서의 일정 연신율 시험을 행하 였다. 탄소 함량이 증가할수록 항복 강도 및 인장 강도는 증가하고 있으며 연신율은 감 소하는 일반적인 경향을 보였으며 비등 질산 시험에서는 탄소량에 관계없이 매우 우수한 내식성을 쁘였다. 또한 비등 상태의 40% NaOH 용액에서의 응력 부식 균열 시험 결과, 탄소량이 증가할수록 부식 저항성이 증가하고 있는 것으로 평가되었다. 한 편 질소량이 증까할수록 결정립이 미세화되었으며 경도값이 상승하였다. 이들 합금 에 대한 양극 분극 시험 결과, 질소량의 변화가 탄소량의 변화보다 내식성에 큰 영향 을 미치고 있음을 알 수 있었다.

• Elastomers and Composites
• /
• v.47 no.3
• /
• pp.231-237
• /
• 2012

This study measured the mechanical and damping properties of EPDM compounds including fillers. Semi-reinforcing furnace black (SRF), high abrasion furnace black (HAF) and acetylene black were used as fillers. Dicumyl peroxide (DCP) were used as curing agents. The measurements were conducted using a moving die rheometer (MDR), durometer, universal testing machine (UTM), compression set and dynamic mechanical analysis (DMA). The tensile strength and elongation at break increased with increasing SRF contents in EPDM compounds. However, they decreased with increasing the amount of acetylene black. In the inspecting temperature range, EPDM compound filled acetylene black had stable storage modulus. Furthermore, the tan ${\delta}$ of the EPDM compounds obtained was enhanced by compounding with acetylene black.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.1245-1249
• /
• 2009

본 연구에서는 우리나라 수문기상인자의 특성변화 분석의 필요성을 지각하여 국내 기상관측소 중 관측년수가 30년 이상인 관측소 63개 지점에 대한 수문기상인자 중 연평균기온, 연평균상대습도, 연강수량, 연증발량, 연일조시간, 연강수계속시간, 연강수일수, 연적설일수, 연신적설일수 등의 자료를 수집하고 기본통계량에 해당하는 평균, 표준편차, 왜곡도, 변동계수를 통하여 수문기상인자의 경년적 변화를 파악하였다. 또한 각종 통계학적 기법을 이용하여 이들 수문기상인자의 경향성, 주기성, 변동성 등을 분석하였으며, 그 결과는 우리 나라를 대표할 수 있는 서울지점을 중심으로 정리하였다. 기본통계량을 분석한 결과 연강수량, 연강수일수, 연강수계속시간의 표준편차와 변동계수가 다른 수문기상인자 비해 상대적으로 큰 것으로 나타나 강수관련 인자들의 경년별 변화가 두드러짐을 알 수 있다. 또한 선형회귀분석과 5년 이동평균 결과 연강수량과 연평균기온은 증가, 연평균상대습도, 연일조시간, 연강수일수, 연증발량은 감소하는 경향을 보였다. Mann-Whitney Test, Wald-Wolfowitz Test, Hotelling-Pabst Test, Wavelet Method와 같은 통계학적기법으로 동질성, 독립성, 검정, 경향성 검정을 수행한 결과 연강수량, 연증발량, 연강수계속시간, 연강수일수, 연적설일수, 연신적설 일수 인자가 각각의 검정에서 동질성 및 독립성을 보였고, 경향성 검정에서는 연평균기온, 연평균상대습도, 연적설일수 인자가 신뢰수준 내에서 유의함을 보였고, 주기성 검정결과 본 연구에 채택한 9개의 수문기상인자들의 연속된 주기성은 나타나지 않았다.