• Korean Journal of Food Science and Technology
• /
• v.26 no.3
• /
• pp.288-294
• /
• 1994

Dietary fiber contents in brans of the two representative Korean rice varieties, Chucheong and Sucheon were measured by the AOAC method, and the composition of total dietary fiber (TDF) was analyzed with the acid detergent fiber (ADF) procedure. Rice bran contained more than 25% of TDF, most of which was insoluble dietary fiber. Hemicellulose was shown to be the major constituent and rice bran dietary fiber contained distinctive amounts of cellulose and uronic acid. Consecutive acidalkaline treatment of rice bran considerably increased soluble dietary fiber (SDF) content and water-holding capacity (WHC). WHC of wheat flour-rice bran dietary fiber mixture increased with the proportion of rice bran dietary fiber. Analysis of the differential scanning calorimetry thermograms revealed that rice bran dietary fiber effectively retarded retrogradation of wheat starch.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.6
• /
• pp.258-263
• /
• 2020

Silicon carbide (SiC) fibers mainly fabricated from polycarbosilane, a ceramic precursor, are applied as reinforcing materials for ceramic matrix composites (CMCs) because of their high temperature oxidation resistance, tensile strength, and light weight. In this study, continuous SiC fibers used to fabricate rope-type flexible heating elements capable of generating high-temperature heat (> 650℃). For high-efficiency heating elements, the resistance of SiC fiber rope was measured by 2-point probe method according to the cross-sectional area and length. In addition, the fabrication conditions of rope-type SiC fiber heating elements were optimized by controlling the oxygen impurities and the size of crystal grains present in the amorphous SiC fiber. As a result, the SiC fiber heating element having a resistance range of about 100~200 Ω exhibited an excellent power consumption efficiency of 1.5 times compared to that of the carbon fiber heating element.

• The Korean Journal of Rheology
• /
• v.1 no.1
• /
• pp.63-70
• /
• 1989

고밀도 폴리에틸렌과 폴리프로필렌을 용융혼합하여 블렌드를 만들었다. 압출물의 morphology 와 유변학적 성질을 측정하고 그 용융하고 섬유의 X-선 회절, 인장 성질, 복굴 절률등과 관련하여 고찰하였다. 파단면의 SEM 사진으로부터 폴리에티렌 성분비가 25%, 50% 에서는 폴리프로필렌이, 75%에서는 폴리에틸렌이 연속상을 이루며 분산상은 고르게 분포함을 알았다 점도와 용융탄성은 모두 폴리에틸렌이 폴리프로필렌보다 크며 블렌드에서 는 그중간에 위치 하였다. 폴리에틸렌의 함량의 증가에 따라 압풀물의 제 1법선 응력차는 증가하였고따라서 방사 섬유의 복굴절률도 증가하였으며 초기 탄성률도 증가하는 경향을 보 였으나 결정 배향도는 조성 의존성을 갖지 않는다. 두 고분자의 비상용성으로 인해 강도는 짓선성에서 벗어나는 거동을 나타내었다.

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.10a
• /
• pp.330-333
• /
• 2001

일반적으로 하나 또는 그 이상의 입자상 충전재 흑은 섬유상 강화재와 연속상인 고분자 기재로 이루어진 고분자 복합재료는 물성이나 기능이 더욱 더 우수한 고성능/고기능성 고분자 재료에 대한 수요가 급격히 증대됨에 따라 이에 대한 많은 연구가 행해지고 있다[1,2]. 그러나 고분자 복합재료의 응력전달은 강화재와 고분자 기재의 계면을 통하여 일어나게 되므로 복합재료의 기계적 물성 등은 충전재의 양, 입자의 크기, 표면성질 뿐만 아니라 강화재와 고분자 기재 사이의 계면 접착력 또는 계면 성질에 크게 좌우된다. (중략)

• Composites Research
• /
• v.16 no.4
• /
• pp.74-79
• /
• 2003

Comparison of interfacial properties and microfailure mechanisms of oxygen-plasma treated poly(p-phenylene-2,6-benzobisoxazole(PBO. Zylon) and poly(p-phenylene terephthalamide)(PPTA, Kevlar) fibers/ epoxy composites were investigated using micromechanical technique and nondestructive acoustic emission(AE). Interfacial shear strength(IFSS) and work of adhesion, Wa of PBO or Kevlar fibers/epoxy composites increased by oxygen-plasma treatment. Plasma-treated Kevlar fiber shooed the maximum critical surface tension and polar term, whereas the untreated PBO fiber showed the minimum value. Microfibril fracture pattern of plasma-treated Kevlar fiber appeared obviously. Based on the propagation of microfibril failure toward core region. the number of AE events for plasma-treated PBO and Kevlar fibers increased significantly. The results oi nondestructive AE were consistent well with microfailure modes by optical observation in microdroplet and two-fiber composites tests.

• Journal of the Korea Institute of Building Construction
• /
• v.8 no.2
• /
• pp.113-119
• /
• 2008

Recently, fiber reinforced polymers(FRP) composite materials are used extensively in the rehabilitation of concrete structural members. A main application is to wrap beams and columns using the continuous fibers sheets to improve their strength and ductility. The corner chamfering affects significantly the performance of the continuous fibers sheets, and could lead to environmental problem with waste and dust. The main purpose of this paper is to verify the effect of corner conditions on the strength of the continuous fiber sheets, and to introduce new attached components which can avoid environmental problem. A total of 15 specimens were tested and carefully checked for three types of continuous fiber sheets(carbon, glass, and aramid) and three types of corner conditions(non-chamfering, chamfering, and device attaching). It is proved that the devices proposed in this research have some capabilities to use for RC member. But additional research will be needed for commercializing.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.3
• /
• pp.293-299
• /
• 2015

We analyzed the damage effect on Glass Fibre Reinforced Plastics(GFRP) under air flow by irradiation of continuous wave near-IR laser. Damage process and temporal temperature distribution were demonstrated and material characteristics were observed with laser intensity, surface flow speed and angle. Surface temperature on GFRP rapidly increased with laser intensity, and the damaged pattern was different with flow characteristics. In case of no flow, penetration on GFRP by burning and flame generation after laser irradiation was appeared at once. GFRP was penetrated by the heat generated from resin ignition. In case of laser irradiation under flow, a flame generated after burning extinguished at once by flow and penetration pattern on GFRP were differently shown with flow angle. From the results, we presented the damage process and its mechanism.

• Composites Research
• /
• v.34 no.6
• /
• pp.400-405
• /
• 2021

In this study, a composite material frame was designed to increase the energy harvesting efficiency of polyvinylidene fluoride (PVDF) ribbon harvesters which are installed inside smart shoes. In order to minimize the amount of deformation in the load direction of the frame, it was designed using carbon continuous fiber composites and its complex shaped structure was manufactured using a 3D printer. In order to calculate the amount of deformation of the insole and midsole of the shoes under the condition of the load generated during walking, the insole and midsole were modeled using the distributed spring elements. Using finite element analysis, the elongation of ribbon-type harvesters mounted on smart shoes was calculated during walking. It is expected that the predicted elongation of the harvester can be utilized to increase the energy harvesting efficiency of smart shoes.

• Composites Research
• /
• v.28 no.4
• /
• pp.239-243
• /
• 2015

Recent studies regarding the properties of carbon nanotubes (CNT) have made remarkable progress in CNT fibers research. However no CNT fibers showed the properties of CNTs because CNTs in fibers have weak interfacial bonding with low shear modulus in the pristine form. Thus, it is upmost interest to develop and employ post-production treatments to the CNT fibers that would potentially improve their properties. In this study, post-treatments resulted in improvement of strength of CNT fibers up to 40%.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.521-528
• /
• 2021

The high-density fiber composite manufacturing method by the extrusion molding method has the characteristic that continuous production is possible, and the product is molded through a mold forming a specific cross-section. OPC is used as a defect material, an appropriate amount of SiO₂ is supplied for CaO reaction activity, and high density and high strength are expressed through steam and autoclave curing. However, due to the use of organic reinforcing fibers, the flame duration exceeds the regulations during the non-combustible performance test, making it difficult to secure performance. In this study, the product was produced by mixing alkali-resistant organic fiber and fly ash having voids as a binder by replacing the existing polypropylene fiber. appeared to be possible.