• Journal of the Earthquake Engineering Society of Korea
• /
• v.15 no.1
• /
• pp.11-18
• /
• 2011

The connection type of steel moment frames in the country is mostly fabricated in factories so that it is fairly ductile due to good quality control. Based on references, the domestic connection satisfies the performance limit for steel intermediate moment frames specified by the AISC. However, the current KBC2009 building code specifies various systems for steel moment frames such as ordinary, intermediate, and special moment frames while the former KBC2005 only did so for a ductile moment frame. This induces the necessity of investigating which system is appropriate in the country when the domestic connection is applied. Therefore, this study was aimed at finding a proper design method by comparing the ductile moment frame in KBC2005 and the intermediate moment frames in KBC2009. The results showed that seismic design parameters for the ductile moment frames can be reasonable for satisfying the performance objective.

• Journal of Korean Association for Spatial Structures
• /
• v.12 no.3
• /
• pp.63-70
• /
• 2012

In this study, the displacement-based design concept, the performance by the existing reinforced concerte column and steel reinforced concrete composite column for SRC purchased the maximum design ground acceleration improvement compared to the performance design. SRC have several advantages such as strength enhancement and high ductility. H-beam or steel tubes were used for embedded elements of the SRC composite columns. SRC cross-section for the P-M diagram and analysis on the nominal bending monent SRC designed for composite columns for disparity estimation is presented to the displacement-based seismic design. Performance improvement of the performance-based design performance targets for the design seismic displacement and design criteria for the direct displacement-based design methods and to improve the seismic performance due to the displacement coefficient method is proposed to design. SRC compared with the RC column designed to improve the performance and displacement ductility ratio displacement results in the performance design results showed significantly improved performance.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.2
• /
• pp.185-189
• /
• 2017

The purpose of earthquake resistant design for typical bridges is the 'No Collapse Design' allowing emergency vehicles just after earthquakes. The Roadway Bridge Design Code provides design provisions to carry out such 'No Collapse Design' with a ductile mechanism and response modification factors given for connections and substructure play key role in this procedure. In case of response modification factors for substructure, the Roadway Bridge Design Code provides values considering ductility and redundancy. On the other hand, 'AASHTO LRFD Bridge Design Specifications' provides values considering additionally an artificial factor according to the bridge importance categories divided into critical, essential and others. In this study, a typical bridge with steel bearing connections and reinforced concrete piers is selected and different response modification factors for substructure are applied with design conditions given in the Roadway Bridge Design Code. Based on the comparison study of the design results, supplementary measures are suggested required by applying different response modification factors for substructure.

• Journal of the KSME
• /
• v.23 no.3
• /
• pp.186-190
• /
• 1983

파괴역학 연구를 대상재료에 의해 구분하면 선형파괴와 탄소성재료의 파괴로 나눌 수 있다. 취 성파괴(brittle fracture)를 다루는 선형타성 파괴역학연구는 주로 여러가지 크랙의 모양, 시편모양, 부하형태에 따른 탄성응력분포 혹은 은력확대계수를 구하거나 에너지방법에 의해 안정비안정 크랙전파를 연구한다. 대개의 경우 취성파괴는 전체 구조물에 치명적이 되기 쉽다. 따라서 구조물 설계시에 취성파괴의 가능성을 배제하기 위해 재료의 적절한 선택과 같은 대책을 강구하는 것이 바람직하다. 다시 말해, 구조물 재료는 강도와 연성의 상황에 따른 적절한 조합을 필요로 한다. 오늘날 특수합금과 같은 고강도 금속에서의 취성화 경향이 증가하나 합금설계시 강도와 아울러 연성을 증가시키기 위한 여러 대책이 파괴역학 연구의 중요한 부분을 차지한다.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.4
• /
• pp.153-160
• /
• 1994

Ten Half precast concrete slabs reinforced with welded deformed wire fabric were tested under two concentrated loads to investigate the flexural moment and ductile capacity. The test variables were the compressive strength of topping concrete, quantitative roughness, and reinforcernent ratio. The effects of each test variables were studied separately. Test results were as followings. The ultimate strength design method is applicable to predict flexural strength for Half P.C. concrete slab with welded deformed wire fabric and quantitative roughness. It is proper to consider 0.0035 strain ;is yielding stress of the welded deformed wire fabric. The ductility index of Half precast concrete slab with welded deformed wire fabric showed lower value. Therefore to enhance the ductility capacity the normal defomed bar should be used with the welded deformed wire fabric for the longitudinal reinforcement.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.12
• /
• pp.101-106
• /
• 2000

As the rotational speed of optical disk drive is increasing nowadays, the reliability to vibration and shock becomes more important. For this, various of rubber vibration isolators are being developed by varying the shape and hardness. But it is difficult for the hardness of common used rubber to be lowered below Duro 30 degrees, and because of the shape complexity of rubber vibration isolator there are difficulties of analysis. Microcellular foamed vibration isolator has various cell densities and cell sizes, so it can vary the stiffness and damping coefficient. In addition, its hardness can be lowered below Duro 30 degrees. Axiomatic Approach is very useful design method for designing new product or new process. Axiomatic Approach's character is scientific and analytical method. In this paper, developing process of microcellular foamed vibration isolator for DVD is presented with Axiomatic Approach.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.157-160
• /
• 2009

멀티 피직스 시스템은 구동을 수치적으로 해석하기 위하여 두 개 이상의 연성이 되어 있는 물리계를 고려해야하는 시스템을 일컫는다. 대표적인 예로 기계 분야에서 현재까지 많이 연구되어 왔던 열탄성(Thermal/Structure)과 유체/구조 연성(Fluid/Structure)시스템을 들 수 있다. 또한 현재 차세대 성장산업으로 많은 관심이 집중되고 있는 의료기기나 지능형 자동차와 로봇 등에서 사용되는 다양한 센서와 엑추에이터 등도 특별한 예로 들 수 있다. 특히, 한 개의 물리계 해석으로 시스템 해석이 가능한 기존의 일반적인 기계 시스템과는 달리 MEMS 등의 초소형 시스템은 시스템의 거동을 수치적으로 계산하기 위하여 여러 물리계의 연성을 고려해야 한다는 점에서 대표적인 다물리계 시스템의 예로 들 수 있다. 이렇게 우리생활에 밀접하게 쓰이고 있는 멀티 피직스 시스템은 단일 물리계 시스템과 비교하여 엔지니어의 경험에 의존하여 설계(Design)하기가 어려운 특성이 있다. 이에 이 연구 논문에서는 이런 멀티 피직스 시스템을 해석하고 최적화 하기위한 노력을 소개한다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.10a
• /
• pp.87-92
• /
• 1993

본 연구에서는 반연성해석(Semi-coupling analysis) 즉 음향 응답이 구조와 음향 시스템의 모달 계수로 표현되는 방법과 구조-음향 연성계수를 이용한 소음저감의 예를 제시한다. 이전까지의 연성해석에서는 해석의 신뢰성을 위 하여 실험에서 구한 구조 모우드를 사용하였다. 그러나 설계단계에서 차실소 음을 예측하고 설계변경의 자료를 제시하기 위해서는 유한요소법을 이용한 예측이 필수적이다. 본 연구에서는 부분 구조 합성법, 주요 결합부에 상세 유한요소 모델의 정적해석등에 의한 등가모델링 기법, 감도해석을 이용한 결 합부 모델링기법을 이용한 유한요소법 구조모우드해석과 그 결과를 이용한 연성해석의 결과를 보여준다.

• Journal of the Korea Concrete Institute
• /
• v.13 no.6
• /
• pp.553-560
• /
• 2001

The ductility capacity should be estimated for inelastic analysis and design of reinforced concrete flexural members. Therefore, to estimate the ductility capacity, the model of moment-curvature relationship of reinforced concrete flexural member is assumed in this study. The curvature, rotation, and displacement(deflection) of reinforced concrete cantilever beams are analyzed and tested. The analytical results are compared with the test results. According to the analytical and test results, the assumed model of moment-curvature relationship in this study is adequate in flexural analysis of reinforced concrete members because the analytical results are well agreed with the test results, and it is resonable to express the ductility capacity in the rotation or displacement ductility, Because the curvature ductility is the limited index in a certain section. It is investigated that the ductility capacity is proportional to lateral reinforcement and compression reinforcement and inversely proportional to tension reinforcement.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.6
• /
• pp.11-19
• /
• 2001

A series of test on concrete-filled composite columns was preformed to evaluate structural performance under axial compression and cyclic lateral loading. It was presented that concrete-filled composite columns had high strength, high stiffness and large energy-absorption capacity on account of mutual confinement between the steel plate and filled-in concrete. A cross section analysis procedure developed to predict the moment-curvature relation of composite columns was proven to be on accurate and effective method. The ductility factor and the response modification factor were evaluated for the seismic design of concrete-filled composite columns. It was shown that concrete-filled composite columns could be used as a very efficient earthquake-resistant structural member.