• Applied Chemistry for Engineering
• /
• v.17 no.6
• /
• pp.575-579
• /
• 2006

Solid electrolyte interface is formed on a carbon electrode used as an anode in Li-ion battery, which can be of $Li^{+}$ intercalation/deintercalation during the first cycle. The passivation film formed by a solvent decomposition during the initial charge process affects cell performance and it was one of the main reason of an initial irreversible capacity. This paper describes the use, for the first time, of $Li_2CO_3$ as the additive for the formation of a passivation film on the carbon surface to suppress the initial irreversible reaction. Chronopotentiometry, cyclic voltammetry, and impedance spectroscopy were used to investigate the effects of the $Li_{2}CO_{3}$ additive. Scanning electron microscopy, energy dispersive X-ray analysis, and X-ray diffraction were also used to monitor changes in the surface morphology and composition of the passivation film formed by solvent decomposition and the precipitation of $Li_{2}CO_{3}$. The addition of $Li_{2}CO_{3}$ to a solution of 1 M $LiPF_{6}$/EC:MA (1:3, v/v) resulted in a decrease in the initial irreversible capacity and it was due to the suppression of the solvent decomposition on the electrode surface.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.5
• /
• pp.1125-1134
• /
• 2011

In this paper a wideband frequency synthesizer is designed for DTV tuners using a $0.18{\mu}m$ CMOS process. It satisfies the DTV frequency band(48~1675MHz). A scheme is proposed to cover the full band using only one VCO and reliable broadband characteristics are achieved by reducing the variations of VCO gains and frequency steps. The simulation results show that the designed VCO has frequency range of 1.85~4.22GHz, phase noise at 4.22GHz of -89.7dBc/Hz@100kHz, gains of 62.4~95.8MHz/V(${\pm}21.0%$) and frequency steps of 22.9~47.9MHz(${\pm}35.3%$). The designed VCO has a phase noise of -89.75dBc/Hz at 100kHz offset. The designed synthesizer has a lock time less than $0.15{\mu}s$. The measured VCO tuning range is 2.05~3.4GHz. The frequency range is shifted down but still satisfy the target range owing to the design for enough margin. The designed circuit consumes 23~27mA from a 1.8V supply, and the chip size including PADs is $2.0mm{\times}1.5mm$.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2143-2145
• /
• 2004

본 논문은 미세공정을 이용하여 다중전극을 배열하여 전압 인가에 의해 선택적으로 약물 방출이 가능한 구역화된 약물 저장용 구조물의 설계 및 제작에 관한 것이다. 두께 525${\mu}m$ 언 (100) Si wafer를 이용하여 TMAH 용액의 조성 및 온도에 따라 Si 식각 기초실험을 하고 그 결과를 이용하여 최적 식각조건을 설정하였다. 구조물 opening 크기를 다양하게 설계하여 미량의 약물을 선택적으로 방출할 수 있게 하고자 역 피라미드 형태의 약물 저장용 구조물을 제작하였다. 전압 인가에 의한 약물 방출시 Au 전극의 특성을 고찰하고자 저장 구조물 위에 anode의 면적과 anode 전극간 거리를 변화시켜서 설계 및 제작하였고, polyimide를 전극 사이의 절연막으로 이용하였다. 제작된 구조품의 전극 특성은 5V의 설정전압을 인가하였을 경우 2500s 동안 0.25mA로 안정적으로 유지되었으나 10V, 15V, 20V일 경우 전극의 산화현상으로 Au 전극이 부식이 되어 전류가 안정적으로 흐르지 않는 것을 알 수 있었으며, 약물전달시스템에서 안정적인 전류 공급을 위해서는 Au 전극이 산화 되지 않는 전압 인가 조건 및 시간은 설정해야 함을 알 수 있었다.

• Journal of the Korean Society for Railway
• /
• v.19 no.3
• /
• pp.314-323
• /
• 2016

Overhead line voltage of DC railway traction substations has rising or falling characteristics depending on the acceleration and regenerative braking of the subway train loads. The suppression of this irregular fluctuation of the line voltage gives rise to improved energy efficiency of both the railway substation and the trains. This paper presents parameter estimation schemes using the RC circuit model for an overhead line voltage at a 1500V DC electric railway traction substation. A linear artificial neural network with a back-propagation learning algorithm was trained using the measurement data for an overhead line voltage and four feeder currents. The least square estimation method was configured to implement batch processing of these measurement data. These estimation results have been presented and performance analysis has been achieved through raw data simulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.10
• /
• pp.1084-1090
• /
• 2009

This paper presents a balun consisting of a T-junction, a Right/Left Handed Transmission line(RLH-TL), and a conventional Right Handed(RH) line. It is assumed that the RLH-TL consists of N unit-cells. We provide closed-form solutions and design a very compact wideband(80 %) balun using CPW lines based on the obtained solutions. Then, we propose a capacitively loaded loop antenna designed for a uniform current distribution. The antenna resistance of the proposed antenna at resonance is about 204 ohms. The length of the unit cell is about $\lambda/12$(total length: $1\;\lambda$). The magnetic field generated from the proposed antenna is stronger than that of the conventional one by as much as 20 dB. We used a coplanar strip line(CPS) to combine the loop antenna and balun. The proposed antenna may be used as a near field UHF RFID reader antenna.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.2
• /
• pp.41-50
• /
• 1993

This paper describes an effort to develop a microcomputer-based parameter identification system for three phase and two phase brushless DC motor. Back EMF equation is derived from back EMF waveform of three phase and two phase brushless DC motor. In this paper, a new identification algorithm for the brushless DC motor parameters by Pasek's technique is developed. It is found that Pasek's equation is valid for the brushless DC motor, too. The results obtained clearly shows that it is possible to implement the identification system for the determination of the brushless DC motor parameters. To minimize errors due to the ripple component in the measured armature current, digital averaging firis employed. The whole identification process of signal generation, measuring, parameter determination is fully automated. The use of the propod method in the parameter identifition system shows that the averaged current curve is in excellent agreement with the estimated current curve. Therefore, this close agreement confirms the validity of this technique.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.2314-2320
• /
• 2015

MBR (Membrane Bio-Reactor) process is known to consume enormous energy to control membrane fouling. To solve this problem, electro-coagulation technique has been applied to MBR. A series of electro-coagulation was applied to activated sludge suspension under different current density condition. After the electro-coagulations, membrane filtration of the activated sludge suspensions was conducted to investigate the effect of electro-coagulation on the fouling. As current density increased 10 to 40A/m2, the total fouling resistance (Rc+Rf) decreased from 18 to 79%, showing that the electro-coagulation improved the membrane filtration efficiency. Both the organic concentration in bulk and the particles size distribution were not nearly changed before and after the electro-coagulation. The enhanced filtration efficiency might be due to the aluminum hydroxide generated from chemical precipitation, which can be acted as a dynamic membrane preventing a deposition of foulants on membrane surfaces.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.6
• /
• pp.897-902
• /
• 2011

This study incorporates a welder and a generator as needed while using the generator to be used as a welder is to configure the system. As such, in order to offer an integrated system to prevent the rapid charging process to manage the power state information, system configuration is the most important. Ideally, the random controls the flow of charge is ideal for that. When charging is good as long as possible, less current. However, In this study, the most ideal fusion welder and generator as required by the generator or welder can be used as a system is proposed. Specifically, the damage can be caused by carelessness, so short-circuit protection, overload protection, reverse polarity protection, automatic charging system is all about, including the ability to adjust.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.242-246
• /
• 2012

This paper presents an integrated low noise and highly linear wideband RF front-end for a digital terrestrial and cable TV tuner, which are used as a part of double-conversion TV tuner. The low noise amplifier (LNA) has a low noise figure and high linearity by adopting a noise canceling technique based on current amplification. The up-conversion mixer and SAW buffer have high linearity by employing a third order intermodulation cancellation technique. The proposed RF front-end is designed in a $0.18{\mu}m$ CMOS and draws 60 mA from a 1.8 V supply voltage. The RF front-end shows a voltage gain of 30 dB, an average single side-band noise figure of 4.2 dB, an IIP2 of 40 dBm, and an IIP3 of -4.5 dBm for the entire band from 48 MHz to 862Hz.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.4
• /
• pp.287-297
• /
• 1998

RPWM(Random Pulse Width Modulation) is a switching technique to spread the voltage and current harmonics on wide frequency area. Using randomly changed switching frequency of the inverter, the power spectrum of the electromagnetic acoustic noise can be spread into the wide-band area. And the wide-band noise is much more comfortable and less annoying than the narrow-band one. So RPWM have been attracting an interest as an excellent reduction method of acoustic noise on the inverter drive system. In this paper a new RPPWM(Random Position PWM) is proposed and implemented. Each of three pulses is located randomly in each switching intervals. Along with the randomization of PWM pulses, the space vector modulation is processed on the C167 microcontroller also. The experimental results show that the voltage and current harmonics were spread into wide band area and that the audible switching noise was reduced by proposed RPPWM method.