• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.829-830
• /
• 2011

• 한국소음진동공학회논문집
• /
• 제21권1호
• /
• pp.74-80
• /
• 2011

Front-back vibrations of high-speed elevator need to be suppressed as in the case of lateral vibrations. The dynamic model for the front-back vibrations is different from the lateral vibration model since the supporting structure varies. In this study, a dynamic model was derived using the energy method. Based on the free vibration analysis, it was observed that the fundamental frequency for the front-back vibration is slightly lower than the fundamental frequency of the lateral vibration, which means that the active vibration control should be carried out in both directions. The PPF control algorithm was applied to the numerical model under measured rail irregularities. The numerical results show that the active vibration control of elevator front-back vibration is also possible.

• 한국소음진동공학회논문집
• /
• 제24권4호
• /
• pp.317-323
• /
• 2014

This study is concerned with the free vibration analysis of an inextensible uniform rope with a spring-mass system at the tip. The rope is hanged vertically in a gravitational field. This problem is related to the free vibration of an elevator rope connected to an elevator cage. The equation of motion and the corresponding boundary conditions are derived by using the Hamilton's principle. The general solution of the governing equation of motion is expressed in terms of Bessel functions. The characteristic equation was derived by applying the boundary conditions. The characteristic values which are in fact non-dimensionalized natural frequencies were obtained numerically. The effects of mass and spring constant were investigated. The numerical results show how the tip mass and spring affect the natural frequencies of the rope.

• 한국소음진동공학회논문집
• /
• 제21권4호
• /
• pp.325-332
• /
• 2011

This paper is concerned with the active control experiments on elevator vibrations by means of the active roller guide. To this end, a roller guide was designed using a voice-coil actuator and linear guide. A simple proportional control algorithm combined with the band-pass filter was implemented using the DSP. Based on the initial experiments, a new control system which can handle lateral and front-back vibrations of elevator was built and tested using the elevator test tower. The experimental results show that the elevator vibrations are reduced by the active control technique.

• 한국소음진동공학회논문집
• /
• 제21권2호
• /
• pp.154-161
• /
• 2011

This paper is concerned with the modeling and active controller design for elevator lateral vibrations. To this end, a dynamic model for the lateral vibration of the elevator consisting of a supporting frame, cage and active roller guides was derived using the energy method. Free vibration analysis was then carried out based on the equations of motion. Active vibration controller was designed based on the PID control algorithm and applied to the numerical model. Rail irregularity were considered as external disturbance in the numerical simulations. The numerical results show that the active vibration control of elevator is possible.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.252-255
• /
• 2014

The elevator rope is easy to oscillate and continue vibrating because the rope structure is flexible and inner damping is small. The vibration of elevator rope is caused by the building vibration excited by external disturbances such as winds and earthquake. This paper is concerned with the experimental verification of the elevator rope vibrations using a small-scale simulator. The elevator rope vibration coupled with the building vibration was modelled using the energy method in the previous study. In this study, the natural frequencies of the elevator rope were computed using the theoretical model and compared to experimental results. Also, the time-responses of the rope vibration during the cage motion were measured by laser sensors and compared to the theoretical predictions. Experimental results are in good agreement with theoretical predictions.

• 한국화재소방학회논문지
• /
• 제33권4호
• /
• pp.89-96
• /
• 2019

본 연구에서는 우선경보방식으로 경보음이 발생되는 경우 발화층과 직상층 이외의 다른 층으로도 전달되는 경보음에 대하여 건축음향 시뮬레이션을 활용하여 서로 다른 엘리베이터 배치를 갖는 3가지 조건에 대하여 예측하였다. 엘리베이터 샤프트에 흡음재가 설치되어 있지 않은 현재 조건으로 예측한 경우, 경보 발생층에서 멀어질수록 전달되는 경보음 크기는 작아졌지만, 3개층이 떨어진 경우에도 약 54 dB(A)~56 dB(A) 크기로 전달되어 일반적인 공동주택의 배경소음 보다 크게 전달되는 것으로 예측되었다. 이전 연구에서 개선안으로 제시된 엘리베이터 샤프트에 흡음재를 적용한 결과 인접층으로 전달되는 경보음 레벨은 약 12 dB~16 dB 정도 작아질 수 있는 것으로 예측되었다. 이는 공동주택의 배경소음 레벨과 유사하거나 작은 정도로 국가화재안전기준에서 규정한 일제경보방식의 의도대로 경보음이 발생되는 발화층과 직상층 이외의 층으로 전달되는 현상을 개선할 수 있을 것으로 판단된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.65-71
• /
• 2012

This paper is concerned with the suppression of brake system noise and vibrations of the elevator traction machine by means of a solenoid control technique. The solenoid is used to hold the brake shoe, which is then released by turning the solenoid off. Since the brake shoe hits the brake disk, vibrations and noise occur. We develop the solenoid control technique based on the dynamic behavior of the solenoid. The theoretical model for the solenoid is modeled by using linear magnetic principles. The solenoid model was then combined with the vibration model to simulate the brake system vibrations. The simulation results show that the additional pulse input to the solenoid can decrease the vibrations. The timing of the applied pulse is determined by observing the current. The experimental results show that both the vibrations and noise can be substantially decreased, which validates the approach developed in this paper.

• 한국소음진동공학회논문집
• /
• 제22권5호
• /
• pp.451-458
• /
• 2012

This paper is concerned with the suppression of noise and vibrations of the brake system of elevator traction machine by means of a solenoid control technique. The solenoid is used to hold the brake shoe, which is then released by turning the solenoid off. Since the brake shoe hits the brake disk, vibrations and noise occur. We developed the solenoid control technique based on the dynamic behavior of the solenoid. The theoretical model for the solenoid is modeled by using linear magnetic principles. The solenoid model was then combined with the vibration model to simulate the vibrations of brake system. The simulation results show that the additional pulse input to the solenoid can decrease the vibrations. The timing of the applied pulse is determined by observing the current. The experimental results show that both the vibrations and noise can be substantially decreased, which validates the approach developed in this paper.

• 한국건축친환경설비학회 논문집
• /
• 제12권6호
• /
• pp.641-654
• /
• 2018

Elevator noise in apartment houses is one of the factors which prevent the residents from quiet and comfortable life. The elevator noise measurement method [KS F ISO 16032] is introduced from the matching ISO standard, however, it has problems in the application to the actual measurement. To visualize the problems, measurements in an apartment house are conducted, which has been suffering from the elevator noise for a long time. The measurement itself is extremely difficult due to the low sound pressure level of elevator, which is lower than 35 dB (A), and the even higher background noise level. However the vibration levels measured at the same time are relatively less disturbing As a result of vibration measurement, it was found that the vibration is clearly measured on the wall, and presents a high correlation coefficient of over 0.8 with the noise levels measured This shows that the vibration level measured on the elevator walls may be rather reliable numbers than the elevator noise levels in the actual noisy condition of elevator halls and the vicinity.