• The Journal of Korean Society for Radiation Therapy
• /
• v.23 no.1
• /
• pp.51-58
• /
• 2011

Purpose: In this study, we tried to check the usefulness of two Linear Accelerators, Clinac IX and 21EX (Varian, Palo Alto, CA), which are equipped in Ajou Medical Center. From 2008 to 2010, we evaluated the error range of Absolute Dose based on the daily output, which was measured by CHECKMATE$^{TM}$ (Sun Nuclear, Melbourne, FL). Materials and Methods: For Daily Q.A, photon beams of two linear accelerators, 21EX and IX (6 MV and 10 MV, respectively) were measured daily by using CHECKMATE$^{TM}$ just before the treatment began, while the absolute dose was measured biweekly by using water phantom. We analyzed the data of measured values from the daily Q.A and the absolute dose from 2008 to 2010 for 21EX, and from 2009 to 2010 for IX. We utilized Excel 2007 (Microsoft, USA) to evaluate Average, Standard deviation and Confidence level of the data. Furthermore, in order to check the measured values of CHECKMATE$^{TM}$ and the significance of absolute dose, each error value was compared and analyzed. Results: During the observation period, the output of two equipment's absolute dose increased in process of time and in both 6 MV and 10 MV, there was a similar increasing trend. In addition, the error rate of the measured value of CHECKMATE$^{TM}$ and the value of absolute dose were under 0.34, which means that there is a similarity relationship between the two measured values. After checking that the measured value of CHECKMATE$^{TM}$ increased, We measured the absolute dose to adjust that. When the error range was close to 2~3%, the number of changing the output was four for 21EX and three for IX. Conclusion: As a result of measuring and analyzing the daily output changes for two years by using CHECKMATE$^{TM}$, we could find that there is a significance between the output which we should obey during Q.A, and the measured value of absolute dose within the error tolerance of 2~3%. Thus, the use of CHECKMATE$^{TM}$ can be positively considered for more efficient and reliable daily output verification of linear accelerator. It can also be a good standard for other medical centers to understand the trends of linear accelerator and to refer to for the correction of each output.

• Progress in Medical Physics
• /
• v.15 no.3
• /
• pp.161-166
• /
• 2004

A simplistic quality assurance (QA) method was designed for a Linac built-in enhanced dynamic wedge (EDW), which can be utilized to make wedged beam distributions. For the purpose of implementing the EDW symmetry QA, a film dosimetry system, low speedy dosimetry film, film densitometer and 3D RTP system were used, and the films irradiated by means of a 60$^{\circ}$ Reversed wedge pair (REWP) method. The profiles were then analyzed in terms of their symmetries, including partial treatment, which is the case of stopping it abruptly during EDW irradiation, and the measured and calculated values compared using the Cad Plan Golden Segmented Treatment Table (Golden STT). The result of this experiment was in good agreement, within 1 %, of the 'reversed wedge pair counterbalance effect'. For the QA of the effective wedge factor (EWF), the authors measured EWFs in relation to the 10$^{\circ}$, 15$^{\circ}$, 20$^{\circ}$, 25$^{\circ}$, 30$^{\circ}$, 45$^{\circ}$ and 60$^{\circ}$ EDW, which were compared with the calculated values using the correction factor derived from the Golden STT and the log files produced automatically during the process of EDW irradiation. By means of this method it was capable of check up the safety of effective wedge factor without any other dosimetry system. The EDW QA was able to be completed within 1 hour from irradiation to analysis as a consequence of the simplified QA procedure, with maximized effectiveness. Unlike the metal wedge system, the EDW system was heavily dependent on the dose rates and jaw movements; therefore, its features could potentially cause inaccuracy. The frequent simplistic QA for the EDW is essential, and could secure against the flaw of dynamic treatment that uses the EDW.

• Applied Chemistry for Engineering
• /
• v.27 no.6
• /
• pp.583-589
• /
• 2016

Lubricant additives including zinc dialkyldithiophosphate (ZDDP) containing metal have been widely used due to the advantage of very low cost, but they can generate impurities such as ash. In this work, ZDDP containing metals was partially replaced with bis[3-(dialkyloxyphosphorothionyl) thio-2-methylpropanyloxy] butane (BAP4s) which was synthesized conveniently and effectively from alkanediol without any metal components. Also, the wear resistance property of synthesized BAP4s were studied. Wear scar diameter (WSD) values of BAP4s with butyl, octyl, decyl, dodecyl or tetradecyl groups were also measured by four-ball test. As the length of the alkyl group increased from 4 to 8, the WSD value of BAP4s decreased rapidly from 0.59 to 0.45 mm, but from 8 to 14, the value increased very slowly from 0.45 to 0.50 mm. Thus, among all BAP4s, B8P4 having BAP4 with the octyl group, showed the lowest WSD value. Furthermore, the WSD values were measured in a lubricant base oil mixed with a 0.50 percent concentration (w/w) of either BAP4 or ZDDP. The former was 0.55 mm, and the latter was 0.45 mm. The thermal stability and tribofilm formation peroperty were also measured by thermogravimetric analyzer (TGA) and energy-dispersive X-rays spectroscopy (EDS), respectively.

• Journal of Bio-Environment Control
• /
• v.33 no.1
• /
• pp.71-78
• /
• 2024

Among the various environmental conditions necessary for growing crops, light is closely related to the anthesis. This study aimed to determine the optimal photoperiod affecting floral differentiation in an edible flower, marigold, to efficiently cultivate the crops in a closed-type plant factory. The experiment was conducted with photoperiods of 4, 8, 12, and 16 hours. French marigold (Tagetes patula L.) 'Durango Red' seeds were sown in polyurethane sponges, and the photoperiod treatments were applied immediately. The extent of floral differentiation was examined at 2-3 day intervals, defined as the visible appearance of flower buds at least 2 mm in size. The growth parameters such as shoot fresh weight and dry weight, height, and leaf area were measured. The optimal photoperiod was determined based on the days when the floral differentiation had occurred in 50% of the total plants. In the 4-hour treatment, proper growth and flower buds did not appear. From the 8-hour treatment, the plant grew normally, and floral differentiation occurred, however, the 8-hour treatment showed the slowest floral differentiation compared to the 12 hours treatments or more. The 12- and 16-hour treatments didn't show significant differences in floral differentiation. While the 16-hour treatment exhibited the highest results in all growth parameters, it was not significantly different from the 12-hour treatment except for shoot dry weight and leaf area. According to the results, 8 hours of photoperiod induced floral differentiation. However, more time was required for flower bud formation, and plant growth was significantly lower compared to photoperiods of 12 hours or more. Considering the energy consumption and its growth, the optimal photoperiod for marigold was 12 hours.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.2
• /
• pp.124-128
• /
• 2000

This study was designed to investigate the effects of sea tangle(Laminaria japonica) extract (Dasi-Ex group: dry base $4.0{\%}$) and fucoidan-added (Fuco-I, II, III group: fucoidan of $1.0{\%}, 2.0{\%}, 3.0{\%}$ added to Dasi-EX) drinks on lipid metabolism of stressed mice. ICR male mice ($20 {\pm} 2 g$) were fed experimental diets and given free through water bottle filled with these beverages instead of water for 18 days including sociopsychological stress of 4 days. Dasi-Ex and Fuco-I, II, III groups resulted in slight decreases $3{\$}$ in body weight gain and $6{\~}12{\%}$ in feed and gross efficiencies compared with control groups. Serum protein contents were slightly increased $1{\~}5{\%}$ by administrations of these beverages compared with control group, reflecting inhibitory effect of sociopsychological stress by increase of protein levels. Significant differences in serum cholesterol contents of Dasi-Ex and Fuco-I groups could not be obtained, but Fuco-II and III groups resulted in marked decreases ($13{\~}17{\%}$) in serum cholesterol contents compared with control group. LDL-cholesterol contents resulted in marked decreases ($about 20 and 25{\%}$, respectively) in Fuco-II and III groups, whereas HDL-cholesterol content was significantly increases ($about 16{\%}$) in Fuco-III group compared with control group. Fuco-I, II and III groups resulted in a marked decreases ($15{\%}, 20{\%} and 40{\%}$, respectively) in atherogenic index (AI) compared with control group. Significant differences in serum lipid peroxide (LPO) contents of Dasi-Ex and Fuco-I groups could not be obtained, but Fuco-II and III groups resulted in a significant decrease about $10{\%}$ in serum LPO contents compared with control group. These results suggested that fucoidan drinks added sea tangle could significantly inhibited chronic degenerative diseases by improvement of effective lipid metabolism or fucoidan component.

• Journal of Animal Environmental Science
• /
• v.18 no.1
• /
• pp.1-8
• /
• 2012

The study was conducted to investigate the effects of climate on indoor environment of a swine house with natural. This study was tested in the beef swine stall at Young-in, Kyung-ki do. The test was experimented for the effect of interior environment by the outdoor environment and the interior-pan. The results are as follows. 1. In test 1 ($T_{out}$ : $25.7^{\circ}C$, without fan), an indoor air flow pattern was showed that entered from sidewall winch-curtain to went out of a indoor by the ridge winch-curtain. And the velocity of a section of the center was measured two times as large as the velocity of the floor. It is the acceleration of the velocity by thermal buoyancy. And, the entered air was rapidly dissipated by flow energy. So that in the swain livestock with sidewall winch-curtain is effected by thermal buoyancy. And the air temperature of the indoor was distributed more higher as compared with the outdoor temperature. This result is caused by the sensible heat from swine and the ventilation is restricted. 2. In test 2 (($T_{out}$ : $25.7^{\circ}C$, with fan), the velocity of a section of the center was measured more higher as compared with the test 1. And the variance of air velocity was distributed higher as compared with the test 1. This result is showed dead region of air flow with a fan operation. And, the variance of gas density was distributed lower as compared with the test 1.

• Resources Recycling
• /
• v.31 no.5
• /
• pp.67-76
• /
• 2022

The furniture industry has a high possibility to create value-added and a high potential to create new occupations due to the characteristics of the industry, which mainly consists of small and medium-sized enterprises (SMEs). However, the used furniture, which has sufficient reuse value, is also crushed and used as solid refuse fuel (SRF) recently. Besides, the number of waste treatment companies continues to decrease, and it occurs congestion of wood waste. As a way to solve the issue, a business model development of remanufacturing used furniture can be suggested as an alternative due to its high circular economic efficiency. Remanufacturing business including furniture industry creates positive effects in various aspects such as economic, environmental and job creation. In other words, remanufacturing is an effective recycling way to reduce input resources and energy in the production process. The results of economic analysis show that the expected annual revenue from the single worker furniture remanufacturing site was 104 million won which is 3.11 times more than the average income of a single-worker household in Korea and its B/C ratio was estimated about 30 which means high business feasibility. Revenue through furniture remanufacturing also showed 320 times higher than that of SRF production from the perspective of weight. In addition, it is shown that the GHGs reduction from the furniture remanufacturing is 2.2 ton CO₂-eq. per year, which is similar to the amount of GHGs absorption effect of 937 pine trees or 622 Korean oak trees annually. Thus the results of this study demonstrate that it is important to adopt an appropriate recycling method considering the economic and environmental effects at the end-of-life stage.

• Journal of Animal Science and Technology
• /
• v.47 no.6
• /
• pp.1001-1008
• /
• 2005

This study examined the effect of corn processing with varying rumen undegradable protein (RUP) on feed intake, milk yield, its composition and, blood characteristics in Holstein cows during the transitional period (21 days pre partum to 21 days post partum). Twenty Holstein cows were randomly assigned to four diets (five cows/diet), ground corn with 30 % RUP (GCR30), ground corn with 40 % RUP (GCR40), flaked corn with 30 % RUP (FCR30), and flaked corn with 40 % RUP (FCR40). The processed corn with varying RUP was fed in total mixed rations (TMR) to cows. Dry matter intake (DMI) was higher with 40 % RUP diet than with 30 % RUP diet, resulting in higher protein and energy intake by cows during pre and post partum (p＜0.05). However, it was not affected by corn processing during pre and post partum. Similarly milk yield was higher with 40 % RUP diet than with 30 % RUP diet. and milk yield was affected by corn processing at RUP 30 % level. Corn processing did not affected the milk fat and protein contents in dairy cows. The concentration of blood non esterified fatty acid (NEFA) were effected by RUP level with flaked corn, however, it was non-significant with RUP levels when given with ground corn. It is concluded that increasing RUP from 30 % to 40 % in iso-nitrogenous diet could increase milk yield in dairy cows during the transitional phase.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.5
• /
• pp.1589-1597
• /
• 2014

For several decades, economic growth has achieved in the aspect of productivity and effectiveness not environmental friendly. As a result, global warming is a major agenda to solve. Therefore, global effort to sustainable development has been adopted like UNFCCC and Kyoto protocol that aimed to reduce greenhouse gas. However, the construction industry has only focused on applying techniques for using less energy sources not monitoring sustainable construction and development. Therefore, this study developed a tool for monitoring greenhouse gas emissions in construction industry. The proposed system evaluates and estimates BAU (Business as usual) for each phase of a construction project. For this purpose, analyzed the greenhouse gas emission factors coincide to life cycle of a construction project. The scope of monitoring is determined according to data availability and emission factor. Then, the system framework is developed and the calculation logic is proposed the system features provide comparison between the emission estimates for eco-friendly design and the actual emission of construction and operation phases. The system would be utilized as a tool for supporting to green construction realization and green construction performance evaluation.

• Korean Journal of Food Science and Technology
• /
• v.12 no.1
• /
• pp.45-52
• /
• 1980

The nylon (poly 6, 10) microcapsules containing ${\beta}-galactosidase$ were obtained by the interfacial polymerization of 1, 6-diaminohexane and sebacoyl chloride with ${\beta}-galactosidase$ from Escherichia coli. They were generally spherical and had a mean diameter of $80{\mu}$ with 45 % of the activity recovery. In particular, there was no transport hamper of lactose through the membrane of microcapsules. The characteristics of the microencapsulated enzyme were similar to those of soluble enzyme optimal pHs, $7.0{\sim}7.2$ for the soluble and $7.3{\sim}7.5$ for the microencapsulated ; optimal temperatures, $50^{\circ}C$ for both ; apparent $K_m,\;3.33{\times}10^{-4}(on ONPG),$ $2.86{\times}10^{-3}$ M(on lactose) for the soluble and $5.28{\times}10^{-4}$ (on ONPG), $4.25{\times}10^{-3}$ M (on lactose) for the microencapsulated ; activation energies, 8.94 for the soluble and 9.78 Kcal/mole for the microencapsulated enzyme. Using this microencapsulated ${\beta}-galactosidase$, hydrolyses of lactose and milk lactose were carried out and 80 % of 5 % lactose solution and 70 % of lactose in skim milk were hydrolyzed in 40 hr at $27^{\circ}C$. The reusability and operational stability showed that the remaining activity was 50 % of the original activity after 5 runs and 120 hr of total operating time at $27^{\circ}C$.