• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.67-70
• /
• 2007

In this study, the characteristic of strength development of high volume fly ash concrete(HVFAC) was experimentally investigated. The production of one ton of portland cement releases about 0.87ton of CO2 into the atmosphere. HVFAC is an emerging material technology and is environmentally friendly because of its reduced use of portland cement, reduced CO2 emissions. For this purpose, two levels of W/B were selected. Seven levels of fly ash replacement ratios and two levels of silica fume replacement ratios were adopted. In the concrete mix, the water content of 125kg/m3 was used, which is less than that of usual water content. As a result, it was observed that the slump of concrete was increased with the increasing fly ash replacement ratio and when the silica fume was incorporated into the concrete, the slump was significantly decreased at the same condition. It appeared that the compressive strength gradually decreased with increasing fly ash replacement ratio at the early age, but the difference of strength up to replacement ratio of 50% was little at the age of 91 days because of the pozzolanic reaction of fly ash.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.21 no.1
• /
• pp.75-81
• /
• 1985

The tensile and dielctric strength of the epoxied resin with bi-directional woven glass fibers with a laminate of two layers(G-10) are studied, and the test parameter is the angle between fiber orientation and the tensile axis. The obtained results may be summaried as follows: 1) when the angle between fiber orientation and tensile axis was varied from 0$^{\circ}$ to 45$^{\circ}$ the yield and fracture stresses have a tendency to decrease with increase in the angle. Especially, the decrease rates in the yield and fracture stresses are changed remarkably in the range of 0$^{\circ}$ to 15$^{\circ}$. 2) The fracture strain has showed the maximum value when the angle between fiber orientation and tensile axis is 45$^{\circ}$, and showed the rapid rate of change from 15$^{\circ}$ to 45$^{\circ}$. 3) For the sample with same angle between fiber orientation and tensile axis the maximum dielectric strength under compressive stress is decreased with increase in tensile stress, when the compressive stress is increased as a parameter of tensile stress. 4) When the angle between fiber orientation and tensile axis is 45$^{\circ}$, the dielectric strength showed the worst value, as the mechanical strength did.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.3
• /
• pp.43-56
• /
• 2018

Vertical cutoff walls such as steel pipe sheet piles (SPSPs) have been commonly applied for the construction of the offshore waste landfill site. Because the SPSPs are sequentially installed by connecting their joints to those of adjacent piles, their mechanical stability should be ensured against the inherent external forces on the sea. The objective of this study is to evaluate the structural performances of the newly developed types of SPSP joint compared with those of other joint types. The problems of the traditional SPSP joints are investigated, and an advanced joint shape of SPSP, which is named double H with L-T (DHLT) joint, are designed for improving the constructability and maintenance. Full-scale models of the DHLT joint are manufactured, and then its joint areas are filled with grout material. After 28 days of curing time, compressive and tensile strength tests were performed on the joint models and the test results were compared with those of the traditional joints. Experimental results show that the structural capacities of the DHLT joint models are lower than those of traditional joints due to the influence of grout and steel members. In the cases of the compressive strength test, especially, bending occurs on steel H-beam with no distinct cracks in grout due to the asymmetrical structure of joint which has no reaction force. This study shows that the performance of the SPSP joint can be improved by considering the influence factors on the structural capacities estimated by the experimental tests.

• The Journal of Engineering Geology
• /
• v.13 no.4
• /
• pp.429-444
• /
• 2003

Domestic marbles are mostly distributed in Gyeonggi and Yeongnam Massifs, southwest and northeast Ogcheon Belts, which belong to Precambrian, age-unknown, Cambrian-Ordovician ages, respectively. The former marbles occur as interbedded rocks in metasediments and xenoliths in granitic gneisses. Age-unknown ones occur as interbedded in the formations of Hyangsanri, Gyeomyeongsan, Hwajeonri and Munjuri, and some in metasedimentary rocks. The latter ones occur as interbedded in Pungchon Limestone, and in Jeongseon Limestone, Hwacheonri Formation and Great Limestone Group, respectively. Among physical properties, porosity shows irregular patterns to density and compressive strength, respectively. Absorption ratio has a linear pattern of positive trend to porosity, and compressive strength mostly shows a positive trend to tensile strength. Compressive strengths of the marbles are as follows : Precambrian $1,106{\;}kg/\textrm{cm}^2$, age-unknown $935{\;}kg/\textrm{cm}^2$. Cambrian $1,162{\;}kg/\textrm{cm}^2$ and Ordovician $1,560{\;}kg/\textrm{cm}^2$, respectively. Tensile strengths have decreasing trends as the above order of geologic age. In diagrams of major elements, $Al_2O_3,{\;}Fe_2O_{3(t)}{\;}and{\;}Na_2O+K_2O$ generally show positive trends with increasing $v_2$. MgO/CaO of Precambrian and age-unknown marbles have much higher values than Cambrian and Ordovician marbles as follows, Precambrian 0.31, age-unknown 0.30, Cambrian 0.03 and Ordovician 0.08. And MgO shows a negative trend with increasing CaO, which nay be caused by dolomitization. By MgO contents they can be classified into calcitic dolomite, dolomitic limestone, limestone and dolomitic limestone, respectively.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.2
• /
• pp.111-118
• /
• 1996

Ship structure basically consists of plate members and it's overall strength depends an the stiffness and strength of each plate member. The buckling strength of plate is one of the most important design criteria when we investigate the structural intergraty. Therefore, it is necessary to surly reasonable buckling formula in order to carry out a more efficient and reliable design. In the present study, the buckling design formula of plate panels under combined loads(inplane compression, tension and shear) is obtained on the theoretical solution or reference paper. This formula is compared with the existing theoretical solution, other author's formula[1], design codes of LR and results which are obtained by numerical analysis. It has a good correlation with numerical analysis results or theoretical ones. When we evaluate buckling strength of plate panels, this formula can be presented with reasonable accuracy.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.3
• /
• pp.227-234
• /
• 2017

This research analyzes the properties of mortar following the rise in water-cement ratio and applicability as an eco-friendly construction supply by using the mudflats of a dredged arena as a substitute for aggregate. The results of a experiment of the flow showed that the flow value decreases as the amount of mudflats increases. A test for chloride content showed that the chloride content increases with the amount of mudflats. In the compression of specimen mixed with mudflat and the testing of tensile strength, the strength weakened as the addition ratio of mudflats rose. However, with 14-day strength as the standard, most specimen showed more strength than the plain, and 14-day strength was higher than 28-day strength. It appears to be experimental error in the mixing process from the viscosity and cohesion of mudflats, and it is considered that there will be a need for an experiment on mixing methods of mudflats in the future. The compressive strength of this research was the strongest with 70% in water-cement ratio, and the tensile strength was strongest with 80% in water-cement ratio. In the evaluation of surface analysis, 70% water-cement ratio, which is finest in strength, mixing, and compactness, was selected to analyze the roughness of the surface, and the results showed that the surface became smoother as the addition ratio of mudflats increases. In conclusion, it appears that 70% water-cement ratio is the optimal mixing ratio for mortar and 10 to 30% addition ratio of mudflats the optimal ratio. It also appears that the application of interior finishing material like bricks and tiles and interior plastering material using the mudflats are possible.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.6
• /
• pp.175-181
• /
• 2009

In this research, experiments were conducted to find out whether polycarboxylate could be used as a crude steel admixture for practical work, depending on the change in the replacement level of the compound mixed into polycarboxylate. Its fluidity was satisfactory, its airspace was a bit smaller than the KS standard, and its unit volume weight was proven to meet the standard. The amount of bleeding was smallest in B2, and in terms of the solidification time, the first and the last solidification was faster in A1, B1, and C1. With regard to the compressive strength in early days as acharacteristic of hardened concrete, all addition rates of 7-day C2 displayed the highest strength value, among which the addition rate of 1.3% had the biggest strength performance tendency. The seal strength also showed the strength performance rate which was about one tenth as big as that of the compressive strength. The length change rate resulting from dryness and contraction was proven to be good, and once the appropriate AE air entraining agent is used, it is evaluated to be a very useful and practical compound out in the field.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.3
• /
• pp.210-215
• /
• 2019

Concrete members with wide surface area are vulnerable to cracking due to material behavior such as hydration heat and drying shrinkage. Recently many researches have been performed on improvement of strength and cracking resistance through fiber reinforcement, which are mainly focused on enhancement of tensile strength against cracking due to material behavior. In this paper, CFs(Cellulous Fibers) are manufactured for slurry type, and the engineering properties in cement mortar incorporated with CFs are evaluated for flow-ability, compressive, and flexural strength. Through SEM analysis, a pull-off characteristics of CF in matrix are analyzed. With CF addition of $0.5kg/m^3{\sim}1.0kg/m^3$, flexural strength is much improved and enough toughness of pull-off is also observed unlike plastic fiber containing smooth surface.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6A
• /
• pp.577-585
• /
• 2009

A 9-node degenerated shell finite element(FE), which has been developed for assessment of ultimate pressure capacity and nonlinear analysis for nuclear containment building is described in this paper. Reissner-Midnlin(RM) assumptions are adopted to develop the shell FE so that transverse shear deformation effects is considered. Material model for concrete prior to cracking is constructed based on the equivalent stress-equivalent strain relationship. Tension stiffening model, shear transfer mechanism and compressive strength reduction model are used to model the material behavior of concrete after cracking. Niwa and Aoyagi-Yamada failure criteria have been adapted to find initial cracking point in compression-tension and tension-tension region, respectively. Finally, the performance of the developed program is tested and demonstrated with several examples. From the numerical tests, the present results show a good agreement with experimental data or other numerical results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.10a
• /
• pp.311-315
• /
• 1992

일반적으로 기계구조물에서는 비교적 응력확대계수 K의 해석이 용이한 판 두께를 관통하는 관통크랙보다는 표면에 존재하는 결함에서 발생, 전파하는 표면 크랙이 대부분이다. 표면은 내부보다 소성변형에 대한 저항이 작고, 대기에 직접 접해 있으며, 평활재에 있어서의 인장, 압축이외의 응력은 일반적으로 표면에서 최대가 되는 등의 이유로 내부보다 쉽게 피로재해를 받는다. 침탄질화 열처리를 하는 중요한 목적이 재료 표면에 있어서 경화능과 피로강도의 향상이므로 침탄질화 처리재의 표면 크랙에 관한 연구가 절실히 요구됨은 당연하다.