• Journal of Korean Society of Environmental Engineers
• /
• 제37권12호
• /
• pp.674-681
• /
• 2015

This research conducts both experimental evaluation and resident's assessment of zero food waste system (ZFWS) in multifamily housing estates in order to explore the feasibility of ZFWS embedded in fermentation and extinction technology utilizing wood chips turned into fertilizer. Having been established in a multifamily housing estate, ZEFWS was proved to be functional and effective. During the 3-month experimental period, the weight between infused food waste and its reactor was reduced significantly enough, and the chemical analysis showed that the concentration of organic compounds went from 87.9% to 75.8%, $H_2O$ decreased from 69.7% to 45.5%, NaCl rose from 0.2% to 0.5%, pH increased from 4.6 to 7.8, and ATP escalated from 505.3 nmol/L to 723.5 nmol/L. Also, the chemical analysis of the output in the experimentation indicated adequacy of the organic fertilizer. In the self-administered questionnaire survey for residents participating in the field project, almost all the respondents viewed that ZFWS can compete with conventional food waste disposal methods and an idealistic way to upcycling food waste into fertilizer.

• Journal of Energy Engineering
• /
• 제25권3호
• /
• pp.73-82
• /
• 2016

The energy consumption efficiency in a variety of operational test mode was considered for domestic gas boiler below 70 kW. The energy efficiency test carried out in the experimental conditions similar to the actual operation status was analyzed and compared with the current Korean efficiency test method. Four types of test modes for each boiler(Non-condensing and condensing boiler) were carried out in the condition of laboratory mode(full load, steady state) and actual operating mode. Futhermore divided into two operational status for each of these, it was applied by maximum gas consumption and consumer sales conditions. Test equipment has the function referred to gas boiler standards, such as KS or European standard EN. The equipment should be continuously measured and record the measuring factors which are the flow volume of gas and water, laboratory temperature, water flow volume for heating, return water volume after heating and quantity of the exhaust gases(CO, NO, $NO_2$). The experimental results were found that non-condensing boiler efficiency of laboratory mode is about 10% higher than that of actual mode. In case of condensing boiler, the efficiency of laboratory condition is about 20% higher than that of the actual using conditions. I suggest that the government will gradually take the efficiency test method considering the actual conditions.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• 제19권11호
• /
• pp.2689-2696
• /
• 2015

Radioactive isotopes which are manufactured using a cyclotron in a radioisotope used for radiation diagnosis is affected by the production yield according to size and shape of the beam and beam uniform degree from irradiated location when the proton beam investigated the target by cyclotron. Therefore, in this paper developed the BPM(Beam Profile Monitor) device capable of measuring the beam cross-section at the cyclotron beam line. It was configured so as to be able to remote control the BPM device in LabView and used the BPM program it was to be able to easily monitor and display to analyze the graph of two-dimensional graph and a three-dimensional beam distribution numerical information of the beam obtained while scanning the tungsten wire to the X and Y axis. The time it takes to measure the beam can be confirmed 37seconds when step motor driving speed was 2000pps. Through a beam readjusted based on the measured beam distribution information by optimizing the beam distribution it can be made to maximize the RI production yield and contribute supply stabilization.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• 제19권3호
• /
• pp.179-184
• /
• 2019

In many countries, such as developing countries where electricity is scarce, small wind turbines in the form of Off Grid are an effective solution to solve power supply problems. In some countries, the expansion of power systems and the decline of electricity-intensive areas have led to the use of small wind power in urban road lighting, mobile communications base stations, aquaculture and seawater desalination. With this change, the size of the small wind power industry is expected to have greater potential than large-scale wind power. In the case of small wind power generators, the generator is controlled at a variable speed, and the voltage and current generated by the generator have many harmonic components. To solve this problem, the AC to DC converter to be studied in this paper is a three-phase step-up type converter with a single switch. The inductor current is controlled in discontinuous mode, and has a characteristic of having a unit power factor by eliminating the harmonic of the input current. The proposed converter is composed of LCL filter and three phase rectification boost converter at the input stage and a single phase full bridge for grid connection. It is a control system with energy storage system(ESS) that the system stabilization can be pursued against the electric power.

• Journal of the Korean GEO-environmental Society
• /
• 제11권9호
• /
• pp.55-60
• /
• 2010

This study are carried out to an lab model tests to develop a construction method that solidifies high-water content cohesive soil by using filter type drain and vacuum pressure, and that stabilizes the ground by accelerating horizontal drain at incline or in tunnel. The calibration chamber was designed within length of 1.5m and height of 50cm, and a drainage hole for preconsolidation, a switchgear and a piezometer were installed at the bottom part of the chamber. Also, a settlement gage was installed at the top part so that it can measure the settlement by time. The calibration ground basis was made in a form of thin layer from kaolinite and bentonite in 9:1 ratio stirred at 130% water content condition. A filter type drain was installed at chamber center and a vacuum pressure of 0.8MPa was applied through a hose linked to the cap at the top part, then, the settlement was measured in every 1 hour interval. After experiment, the moisture contents were measured by position, then, verified the increase of solidity of the ground through a triaxial compression test on undisturbed profile. After 11 days from the effective date, it was observed that the settlement decreased by maximum 35mm and the water content ratio was reduced by 38% at most while the solidity of the ground increased by 5~8 times greater than before preconsolidation.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.79-79
• /
• 2010

다른 물질에 비해 많은 우수한 특성을 가지고 있는 CuInSe2(CIS)박막 태양전지는 많은 연구자들에 의해 개발되어 오고 있다. CIS의 대표적인 장점으로는 직접천이형 밴드갭, 높은 흡수계수, 열 안정화상태 및 p형으로의 전도성물질의 가능성 등 다양하다. 또한 간단한 구조를 이용하여 유리같은 싼 기판을 이용하기 때문에 저가형 태양전지로서 많은 각광을 받고 있다. CIGS태양전지는 CIS의 In 사이트에 Ga을 도핑함으로서 만들어지는데 밴드갭은 약 1.4eV이다. CIS박막을 만드는 많은 방법이 존재하나 구성원소로부터 최적화된 조성을 찾을수 있는 방법이 가장 중요한 요소 중의 하나로 인식되고 있으며, 이런점에서 증발법 및 스퍼터링법 등 같은 진공방식이 비진공방식에 비해 훨씬 간편하게 조성비를 맞출수 있다. 그 중에 스퍼터링법은 대면적 박막태양전지로의 가능성으로 비출어 볼때 산업화를 위한 좋은 후보군이 될 수 있다. Selenization을 하기전에 Cu-In-Se의 전구체 조합은 여러개의 타겟으로부터 동시 스퍼터링법이나 다층 전구체법을 사용하여 준비되는데 어떤 방법이 되던지 Se의 부가적인 공급은 불가피하다. 지금까지 많은 관련 연구의 대부분인 구조적, 조성비적 그리고 광학적인 특성평가에 집중되어 오고 있는데, 전기적특성평가의 경우는 면저항, 비저항 같은 간단한 결과 위주로 보고되어 오고 있다. 또한 캐리어농도와 이동도에 대한 보고가 있음에도 불구하고 이해되기에는 충분치 못한 면이 많다.본 발표에서는 태양전지 제조 전단계로서 소다라임유리기판(SLG)위에 Mo의 유무에 따라 CIS박막의 전기적인 특성 변화에 대한 내용을 담고 있다. 소다라임유리($2cm{\times}2cm$)를 기판으로 사용하여 아세톤-에탄올 용액에 초음파세척을 수행하고, Mo 후면전극을 DC 스퍼터링방식을 이용하여 증착을 한다. SLG와 Mo이 코팅된 SLG를 각각 RF 스퍼터 챔버에 이송한 후 수증기 제거를 위해 약 10분간 예열을 한다. 샘플에 대한 전기적특성은 Hall효과 측정장치에 의해 측정이 되며 전기전도도, 캐리어농도, 이동도 및 전도형에 대한 정보가 각각의 변수에 따라 조사된돠. 부가적으로 구조적, 조성비적인 특성을 SEM,XRD 및 EDX를 통해 조사를 하여 전기적 특성에 따른 관계성을 검토한다. SLG와 Mo가 코팅된 SLG위의 CIS박막은 전기적으로 약간 다른 특성을 보일 것으로 예측되며, 이러한 기대를 바탕으로 조성비가 이상적인 화학양론에 근접할 때 p형으로서 제시될 수 있다는 것을 보여줄 것이다.

• Fire Science and Engineering
• /
• 제34권2호
• /
• pp.14-21
• /
• 2020

This paper presents the study of a fire risk to the backside of two miniatures of ISO 9705 2/5 using a lightweight partition for indoor space division and reproduction of the ISO 9705 test. An SGP partition, stud partition, glass wool panel, urethane foam panel, sandwich panel, and glass partition were selected as the test specimens, which are frequently used in construction. According to the ISO 9705 test standard, stabilization was achieved using a measuring device that recorded data before the ignition of a burner and continued recording for 120 s thereafter. After ignition was achieved, the power was increased to 300 kW for 600 s and then reduced to 100 kW for 600 s. The specimens were subsequently observed for 180 s, and the fire risk to the backside and the fire pattern of the wall unit were analyzed. Owing to the amount of heat generated by the ignition source, the maximum temperature of the backside was observed to be 67.7 ℃ for the SGP partition, 55.1 ℃ for the stud partition, 52.4 ℃ for the glass wool panel, 727.4 ℃ for the sandwich panel, 561 ℃ for the urethane foam panel, and 630.5 ℃ for the glass partition. In the cases of the sandwich and urethane foam panels, the explosion of flammable gas occurred by virtue of fusion of the interior materials. The reinforced glass was fractured owing to the temperature difference between the heat- and nonheat-responsive parts. Ultimately, the fire risk to the nearby section room was deemed to be high.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제21권6호
• /
• pp.403-410
• /
• 2020

This paper focuses on the design of a 12-kW small-scale supercritical CO₂ test loop. A theoretical study, stabilization, and optimization of carbon dioxide were carried out with the application of a solar heat source based on solar thermal data in Pohang. The thermodynamic cycle of the test facility is a Rankine cycle (transcritical cycle), which contains liquid, gas, and supercritical CO₂. The system is designed to achieve 6.98% efficiency at a maximum pressure of 12 MPa and a maximum temperature of 70℃. In addition, the optimum turbine inlet temperature and pressure were calculated to increase the cycle efficiency, and the application of an internal heat exchanger (IHX) was simulated. It was found that the maximum efficiency increases to 18.75%. The simulation confirmed that the efficiency of the cycle is 6.7% in May and 6.26% in June.

• Proceedings of the Korea Water Resources Association Conference
• /
• 한국수자원학회 2006년도 학술발표회 논문집
• /
• pp.1073-1077
• /
• 2006

급속한 산업화로 인한 오염물질의 증가와 생물서식처의 감소는 수자원과 생태계를 위협하고 있다. 국내의 경우 수자원의 질을 개선하기 위해 '90년대 초부터 하수처리시설 등의 저감시설을 대폭 확충하였으나 현재까지 팔당호 등 주요상수원이 목표수질에 못 미치고 있으며 그 원인은 유입오염물질의 $22{\sim}37%$를 차지하는 비점오염원으로 지목되고 있다. 또한 생태.경관적 가치가 높은 수변지역은 각종 개발로 생물서식처가 급속도로 감소하여 종 다양성 보전 측면에서 대책마련이 시급한 실정이다. 이와 유사한 상황에 직면한 선진외국에서는 '하천회랑(river corridor)' 또는 '토양 및 생태시스템을 포함하는 수역과 육역의 점이(漸移)지대'를 의미하는 이른바 '수변완충지대(Riparian Buffer Zones)'의 오염정화 및 생태조성 효과 등의 연구를 통해 효율적 조성방안을 제시하고 있으며 다양한 형태로 현장에 적용하고 있다. RBZs의 일반적인 기능으로는, 유사나 오염물질의 여과 및 차단(필터링 효과), 영양염류의 저감, 하천변 식생을 통한 수자원의 정화 및 강턱의 안정화, 홍수로 인한 하천침식의 방지, 수변 생물 서식처 제공, 수변 그늘 제공에 의한 수온상승 방지, 심미 교육 위락 공간 제공 등이다. 본 연구에서는 외국의 RBZs(Riparian Buffer Zones)가이드라인을 참고하여 국내실정에 맞는 파일럿 규모의 시험완충지를 설계 및 조성하였다. 시험완충지는 남한강 연안에 초본류, 갈대류, 관목류, 자연식생, 혼합식생 등 5가지 'dry biotope'형태로 설치하여 1년간 계절별로 운영하였다. 또한 실험의 정량화와 다양한 조건변화를 위해 차수막, 위어, 유량.농도 조절장치, 라이시미터 등 보조시설을 설치하였고, 정기적인 모니터링을 실시하였다. 조사결과 외국사례를 살펴보면 RBZs의 적정 폭은 수질정화기능의 경우 $15{\sim}30m$, 생태서식처 기능은 최소 90m이상으로 제시되며, 시험완충지의 수질정화효과는 SS, T-N, T-P, TOC의 평균저감율이 각각 50%이상으로 나타났다. 식생모니터링 결과, 환삼덩굴 등 우점종의 잠식속도는 약 15일이며 갈대와 갯버들의 경우 우기시 인공목책호안과 동일한 침식방지 효과를 보이는 것으로 관찰되어 식생의 주기적인 모니터링과 지역 특성에 적합한 우점종 선정이 매우 중요한 것으로 판단된다.

• Journal of the Korean Institute of Gas
• /
• 제18권1호
• /
• pp.46-51
• /
• 2014

The purpose of this paper is to study of the vehicle lamp manufacturing system composing ultrasonic waves connection process. Making lamp assembly plant, it was produced in the separate process as the injection molding, ultrasonic waves bonding, annealing in the constant temperature, lamp assembling and packing. But the improvement method producing the lamp was added with one-step process by one automation technique. As a result, welding with ultrasonic waves process, the method decreased the energy consumption and noise during ultrasonic waves welding. Therefore, this method used the mathematics modeling for checking validity, it selected the stability and suitable controller using transfer function of plant and bode chart. In this study, the $180^{\circ}$ revolution control system to turn injection part upside down was $M_{eq}\;lcos{\theta}(t)$ because of gravity influence. It effected to unstable condition a system. For solving this problem, it aimed the linearization and stabilization of system by elimination $M_{eq}\;lcos{\theta}(t)$ as applying Free-forward control technique.