• Journal of the Korean Institute of Gas
• /
• v.22 no.6
• /
• pp.76-89
• /
• 2018

The distribution of the combined heat and power system is active as a solution to the instability of energy supply and environmental pollution caused by continuous industrial development. In Korea, the safety standards for combined heat and power system using a gas engine are insufficient therefore the study on this is needed. In this study, the safety performance and structural/material assessment items of domestic and international standards applied to the combined heat and power system were analyzed to carry out a standardization study on safety performance applicable to 20 kW gas engine combined heat and power system. In addition, the safety performance assessment (plan) of the gas engine combined heat and power system was derived by performing risk analysis and risk assessment using HAZOP. Assessment items include engine ignition systems related to safety performance, piping tight performance, watering and temperature rise performance, combustion performance, electrical efficiency, thermal efficiency, overall efficiency and humidity performance. Gas and water pipes, gas control and shut-off valves, durability, heat resistance, and cold resistance of metal or non-metallic materials related to the structure and materials of the gas engine combined heat and power systems.

• Journal of Convergence for Information Technology
• /
• v.7 no.5
• /
• pp.103-109
• /
• 2017

A pressure vessel is a cylindrical container that accommodates a pressurized fluid. In real life, there are propane canisters and butane canisters. According to data from the Korea Gas Safety Corporation, The number of domestic gas accidents is average 33 cases of domestic gas accidents occurred per year and 20.8 for mobile butane gases. The purpose of this study was to investigate a method to prevent this kind of explosion. Common studies include forced drain through safe holes, forced separation of butane canisters, and manufacturing of high-strength steel. This paper uses a concept that reduces stress inside the cylinder using prestressed method that precede compression. In other words, install a long liner in both ends of the pressure vessel. I want to develop a safety device that acts like a gas intermediate valve.

• Journal of Navigation and Port Research
• /
• v.29 no.10 s.106
• /
• pp.865-870
• /
• 2005

Because there are only a limited number of means of action that are available for the master to pursue in the event of flooding, onboard decision support system has been required. The majority of systems activated during a flooding emergency (such as watertight and semi-watertight doors, bulkhead valves, dewatering pumps etc.) almost exclusively aim to restore a sufficiently high level of subdivision to prevent flooding from spreading through the ship. Even though assuming the flooding scenario is not catastrophic, the use of ballast tanks can be an additional and very effective tool to ensure both prevention of flooding spreading and also improve ship stability. This paper describes an optimization algorithm devised to choose the set of ballast tanks that should be filled in order to achieve an optimal response to a flooding accident.

• Journal of the Korean Institute of Gas
• /
• v.17 no.1
• /
• pp.73-80
• /
• 2013

This study presents sealing behavior and endurance safety of V-grooved o-rings as functions of a strain, compression stress, and contact normal stress using a FEM technique. The FEM results on the sealing behavior and endurance safety show that the maximum strain, maximum compression stress, and maximum contact normal stress of V-grooved o-rings are approximately 1.2 times higher than those of conventional solid o-rings. This is why that an o-ring has a V-groove in the center between two overlapped circles, which is very effective in sealing for ball valves, pressure vessels, and gas equipment. And the extrusion failure in V-grooved o-rings does not take place under an increased gas pressure due to a V-groove. This may extend sealing life compared with that of a conventional solid o-ring.

• Korean Chemical Engineering Research
• /
• v.56 no.3
• /
• pp.335-342
• /
• 2018

Various technologies to cope with the energy and environmental issues related to the chemical and electric power industry are in development and demonstration stage. Especially, the absorption process of carbon dioxide ($CO_2$) using amine solution is a key technology of the $CO_2$ capture and storage (CCS). In this study, we identify the major risk factors and suggest strategies for safety improvement by analyzing and assessing commercial the amine-based $CO_2$ separation process. HAZOP method was used to assess the risk for the process. We provide facilities and operational strategies to mitigate or eliminate major risk factors by assessing the relative ranks of identified risk factors using a risk matrix.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2005.10a
• /
• pp.75-80
• /
• 2005

Because there are only a limited number of means of action that are available for the master to pursue in the event of flooding, onboard decision support system has been required The majority of systems activated during a flooding emergency (such as watertight and semi-watertight doors, bulkhead valves, dewatering pumps etc.) almost exclusively aim to restore a sufficiently high level of subdivision to prevent flooding from spreading through the ship. Even though assuming the flooding scenario is not catastrophic, the use of ballast tanks can be an additional and very effective tool to ensure both prevention of flooding spreading and also improve ship stability. This paper describes an optimization algorithm devised to choose the set of ballast tanks that should be filled in order to achieve an optimal response to a flooding accident.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1996.04a
• /
• pp.215-220
• /
• 1996

원자력발전소의 주증기관은 증기발생기와 터빈을 연결하는 주요 계통으로서 여기서 발생하는 배관진동은 주요기기의 연결부, 밸브, 배관지지물과 건물 등에 복합적인 반복하중을 가하여 관련 지지물 및 구조물에 열화현상을 발생시켜 발전소의 안전운전에 심각한 영향을 초래할 가능성을 항상 내포하고 있다. 그럼에도 불구하고 배관진동 대책은 대부분 지지물을 추가로 설치하여 진동준위만 낮추고 있는 실정이다. 따라서 구체적인 배관진동의 예측, 측정 및 평가, 감쇠방안에 이르는 종합적이고 체계적인 연구가 요구되고 있다. 본 연구에서는 지지물의 열화현상 및 부분적인 파손으로 진동준위가 높아진 것으로 추정되는 원자력발전소 주증기관의 진동특성 및 요인을 분석하여 진동감쇠 방안을 도출하고 검증함으로써 배관 및 주변 구조물의 건전성을 확보하고 설비의 신뢰성을 확보하고자 하였다. 이를 위하여 주증기관을 모델링하여 해석하였으며, 발전소의 기동 및 정상운전시의 진동준위를 측정하였다. 또한 발전소의 정진기간중 일부 배관계에 대한 실험적 모우드 해석을 수행하였다. 여러가지 진동감쇠 방안을 검토하여 탄성지지 및 에너지 흡수효과를 동시에 발휘할 수 있는 특수 지지물(WEAR$_{TM}$)을 설치하는 방안을 도출하였으며, 현장에 설치한 후 배관의 진동상태를 확인함으로서 효과적인 방안임을 검증하였다.

• Nuclear Engineering and Technology
• /
• v.24 no.3
• /
• pp.311-318
• /
• 1992

During mid-loop operation of Nuclear Power Plant, to prevent the Decay Heat Removal System (DHRS) from failure due to air entrainment of free surface vortex in the piping system, a set of simulating experiments was performed. Through these experiments, a relation between the non-dimensionalized numbers, such as H/d, Froude number, Reynolds number, was found. It was also found that the perturbation of the system by the disturbance such as pump start, valve operation, etc., has a strong effect on the free surface vortex. Furthermore, from viewpoint of reactor safety, a modified inlet device which is reducer type is strongly recommended for the prevention of air entrainment into DHRS.

• Journal of Korean Society for Geospatial Information Science
• /
• v.10 no.2 s.20
• /
• pp.97-105
• /
• 2002

Nowadays the gas utilities has been increasing constantly due to the expansion of the urban areas. The gas utility companies have adopted GIS technologies and been trying to computerize the management system for gas facilities to maintain up-to-dated information to forecast possible accidents and to minimize the casualties from the accidents. The major objective of this study is to develop a GIS-based gas accident management system which could facilitate early response and alternatives in the cases of the accidents. The system is able to provide the information for the pipes to be closed followed by selecting the location of the accident, and search all the relevant values connected to the location to provide all the information to minimize the casualties. In addition to that, the system can calculated the remaining amount of the gas in the pipes closed from the accident thereby providing more safer alternatives. In the future, more practical method needs to be made such as GPS-linked more integrated gas accident management system.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.6
• /
• pp.81-87
• /
• 2023

SAE J2601 and SAE J2799, the communication protocols between a hydrogen refueling station and a fuel cell electric vehicle, only cover hydrogen charging. In this paper, we measure the hydrogen detection, current, and voltage of a fuel cell electric vehicle and transmit the sensor data to the hydrogen refueling station by changing the WiFi protocol. A small-scale laboratory model was built using Raspberry Pi for sensing, controlling, and transmitting sensor data of a fuel cell electric vehicle. The sensor data was stored in the database of the hydrogen refueling station, and a dashboard was configured using Grafana to analyze the stored data. When hydrogen is detected, the dispenser valve of the hydrogen refueling station is locked. Then, we measured the average transmission delay according to the WiFi protocol. The results showed that IEEE 802.11a is the most suitable WiFi protocol for transmitting sensor data between the hydrogen refueling station and the fuel cell electric vehicle.