• Journal of Advanced Navigation Technology
• /
• v.23 no.1
• /
• pp.90-96
• /
• 2019

LPWA is a cost-effective and time-saving technology with wide coverage. However, the LPWA is an ISM band that uses UHF radio waves, and its performance is very poor indoors because of its strong linearity. But, because of the possibility of achieving high performance compared to other communication in the room, this paper has studied the indoor communication performance by applying LoRa in LPWA technologies. After installing the data receiving module on the 4th floor, the transmission module was placed at the end of the building from the same floor to the 1st floor, and the data was collected. As a results, it installed on the 1st floor can be collected data with 98 ~ 99% probability, and the lowest RSSI is about -116dBm. Thus, considering the specification of LoRa with a maximum reception sensitivity -136dBm when the spreading factor is 12, the application of LPWA in the industrial field can be fully considered.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.786-791
• /
• 2021

In this paper, in order to minimize limitations such as signal interference and positioning errors in existing indoor positioning systems, a smart LED-based positioning system for excellent line-of-sight radio environments and precise location tracking is proposed to improve accuracy. An IEEE 802.4 Zigbee module is mounted on the SMPS board of a smart LED; RSSI and LQI signals are received from a moving tag, and the system is configured to transmit the measured data to the positioning server through a gateway. For the experiment, the necessary hardware, such as the gateway and the smart LED module, were separately designed, and the experiment was conducted after configuring the system in an external field office. The positioning error was within 70cm as a result of performing complex calculations in the positioning server after transmitting a vector value of the moving object obtained from the direction sensor, together with a signal from the moving object received by the smart LED. The result is a significantly improved positioning error, compared to an existing short-range wireless communications-based system, and shows the level at which commercial products can be implemented.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.05a
• /
• pp.355-357
• /
• 2022

In this paper, as a positioning technology for predicting the movement path of a moving object using a recurrent neural network (RNN) model, which is a deep learning network, in an indoor environment, continuous location information is used to predict the path of a moving vehicle within a local path. We propose a movement path generation technique that can reduce decision errors. In the case of an indoor environment where GPS information is not available, the data set must be continuous and sequential in order to apply the RNN model. However, Wi-Fi radio fingerprint data cannot be used as RNN data because continuity is not guaranteed as characteristic information about a specific location at the time of collection. Therefore, we propose a movement path generation technique for a vehicle moving a local path in an indoor environment by giving the necessary sequential location continuity to the RNN model.

• The Journal of the Acoustical Society of Korea
• /
• v.27 no.1
• /
• pp.1-11
• /
• 2008

To overcome the mid frequency limitation of geometrical acoustic techniques, the phased geometrical method was suggested by introducing the phase information into the sound propagation from the source. By virtue of phase information, the phased tracing method has a definite benefit in taking the interference phenomenon at mid frequencies into account. Still, this analysis technique has suffered from difficulties in dealing with low frequency phenomena, so called, wave nature of sound. At low frequencies, diffraction at corners, edges, and obstacles can cause errors in simulating the transfer function and the impulse response. Due to the use of real valued absorption coefficient, simulated results have shown a discrepancy with measured data. Thus, incorrect phase of the reflection characteristic of a wall should be corrected. In this work, the uniform theory of diffraction was integrated into the phased beam tracing method (PBTM) and the result was compared to the ordinary PBTM. By changing the phase of the reflection coefficient, effects of phase information were investigated. Incorporating such error compensation methods, the acoustic prediction by PBTM can be further extended to low frequency range with improved accuracy in the room acoustic field.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.6
• /
• pp.1510-1517
• /
• 1995

A theoretical method is described to simulate the propagation of turbulent premixed flames in a closed vessel. The objective is to develop and test an efficient technique to predict the propagation speed of flame as well as the geometric structure of the flame surfaces. Flame is advected by the statistically generated turbulent flow field and propagates as a wave by solving twodimensional Hamilton-Jacobi equation. In the simulation of the unburned gas flow field, following turbulence properties were satisfied: mean velocity field, turbulence intensities, spatial and temporal correlations of velocity fluctuations. It is assumed that these properties are not affected by the expansion of the burned gas region. Predictions were compared with existing experimental data for flames propagating in a closed vessel charged with hydrogen/air mixture with various turbulence intensities and Reynolds numbers. Comparisons were made in flame radius growth rate, rms flame radius fluctuations, and average perimeter and fractal dimensions of the flame boundaries. Two dimensional time dependent simulation resulted in correct trends of the measured flame data. The reasonable behavior and high efficiency proves the usefulness of this method in difficult problems of flame propagation such as in internal combustion engines.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.1
• /
• pp.90-97
• /
• 2004

In this paper, the optimal position selection of error microphones and control speakers to attenuate interior noise from outside noise sources using active noise control techniques is presented. To get an optimal control characteristics of adaptive noise control systems, it is necessary to optimize the positions of microphones and speakers. New type of simulated annealing method has been proposed as searching techniques to find optimal speakers and microphones positions in which the sum of the squared pressures at microphone positions in an enclosure can be best minimized. Computer simulations and experiments have been performed to show the effectiveness of the proposed method.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.43-46
• /
• 2003

This paper presents capacity characteristics of the indoor LOS(Line-Of-Sight) propagation channel for MIMO system at 5GHz. The distance between antenna elements, their moving path, and number of transmitting and receiving antennas can be determined by wanted eigen-vlaue, and channel capacity of the MIMO communication channel using only reliable simulation without measurements. The simulation uses 3D Ray tracing and patch scattering model to which electromagnetic material constants are applied. As distance between antenna elements increases, distribution of the eigen-value show a tendency to decrease, but channel capacity increases in LOS environment. However, despite of short distance between antenna elements, large value of channel capacity is obtained in positions which have high AS. When the position of receiver antennas are shifted, channel capacity hardly changed, and as number of antenna elements increases, channel capacity also increases regularly.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.11
• /
• pp.933-940
• /
• 2006

In this study multi-zone modeling program CONTAM 2.4 developed by NIST is used for estimating the air disinfection rate of the interior of a room which is set up the indoor air disinfection system with filter and ultra violet germicidal irradiation (UVGI). Developed models those enable to predict the transmission of air home contagion such as bacteria and fungus generated in our daily life are useful model for designning air cleaning & ventilation system of building. Also, results indicate that these models are enable to compute the real situation that is almost impossible of carrying out experiment in an actual condition due to biohazard problems and suggest that engineers will use these models as a design tool for the future immune building system.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2010.11a
• /
• pp.1384-1387
• /
• 2010

최근 무선인터넷의 기술을 이용한 스마트폰의 활용도가 높아짐에 따라 새로운 서비스의 연구분야로 단말기를 이용하여 이동객체의 위치정보를 제공받는 위치 기반 서비스 기술에 관심이 높아지고 있다. 하지만 현재 기술은 GPS를 이용한 위치추적으로 외부의 이동객체를 추적하는 기술로 많이 활용되고 있다. 그리고 고정된 레퍼런스 노드 또는 마스터 노드에 의존하고 있는 문제점과 위치 계산을 위한 기준이 대부분 홉스나 RF신호의 수신강도에 의한 거리차를 이용하는데 전파 특성에 따른 회절 및 반사, 다중 경로 등에 의한 신호감쇠현상으로 정확도를 보장하지 못하는 문제점이 있다. 따라서 본 논문에서는 GPS와 WiFi를 이용하여 고정된 레퍼런스 노드에 의존하지 않고 이동식 GPS-AP를 이용하여 건물내부에 위치하는 특정 단말기의 위치정보를 제공할 수 있는 시스템을 제안한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.47-49
• /
• 2022

IPS is an indoor positioning system that replaces GPS, which is less accurate due to walls and roofs inside buildings. Radio signals such as Wi-Fi are used instead of satellite signals, and complex methods are being used to increase accuracy. In this paper, we present a more efficient positioning method than before by applying high-level signals to high-accuracy fingerprint techniques. A radio map is configured with high-level signals collected by utilizing Wi-Fi APs, which are more than in the past. The suitability of use was confirmed by analyzing the pattern represented by the configured radio map for each location.