• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 1995.03a
• /
• pp.92-100
• /
• 1995

최근 지하 공간의 활용이 증대되는 추세에 이와 관련되어 지하 구조물의 시공전 또는 시공 중에 있어 시공 전략 수립, 장비 결정, 안정성 및 경제성 등을 위해 암반 내의 파쇄대나 균열대의 발달 및 분포에 대한 탐사는 필수적으로 선행되어야 한다. 이러한 탐사에는 분해능이 매우 높은 탐사 기술이 요구되며, 일반적으로 시추공이나 지하 갱도를 이용한 탄성파 탐사나 지오레이다(georadar) 탐사를 많이 사용하고, 자료해석을 위한 역산 기법으로는 지오토모그래피(geotomography)가 필수적인 기법으로 인식되고 있다. (중략)

• Tunnel and Underground Space
• /
• v.26 no.4
• /
• pp.304-315
• /
• 2016

In this study, the current horizontal stress characteristics of the Tertiary rock formations in the Pohang Basin are investigated on the basis of the in-situ rock stress measurements at depths from 75 m to 716 m of the 3 test boreholes in the Doumsan area, Pohang. The deep hydraulic fracturing stress measurement results indicated that the horizontal stress components in the test site appear far lower than the average ones by the linear fit for the data set measured from the other domestic sites. But, borehole scanning revealed clearly that lots of small and large scale borehole failures occurred due to the low strength characteristics of the existing rocks. To obtain more accurate and overall information on the horizontal stress direction, the integrated analysis combining the hydraulic fracturing stress measurement and borehole scanning data set were additionally carried out. The analysis results showed that in the upper sedimentary and the lower volcanic rock formation, the dominant orientations of the current maximum horizontal stress components were appeared in the range of $80^{\circ}{\sim}100^{\circ}$ (N80E~N80W) and $120^{\circ}{\sim}140^{\circ}$ (N60W~N40W), respectively. From this study result it was found that the maximum horizontal stress directions have a tendency to rotate in a clockwise direction as the rock formation changes with depth in the test site.

• Tunnel and Underground Space
• /
• v.28 no.3
• /
• pp.232-246
• /
• 2018

In this study, the relationship between in situ seismic wave velocities and RMR (rock mass rating) was investigated in a test bed for the examination of the basis of rock classification (RMR) based on seismic wave velocity. The seismic wave velocity showed a monotonous increase with depth. It was also found that there was no systematic correlation between the seismic wave velocity (Vp) and other parameters (RQD, joint spacing, UCS, rock core Vp, and RMR) collected at the same depth of the same borehole. However, correlative relation was observed among RMR, RQD, and joint spacing. On the other hand, when all the data in the borehole (three holes) are examined without considering the depth, Vp still shows no correlation with RMR parameters (e.g., correlative coefficient for uniaxial compressive strength and joint spacing are 0.039 and 0.091, respectively), but Vp shows weak correlative relation with RMR and RQD (correlative coefficient for RQD and RMR are 0.193 and 0.211, respectively). Thus, it is found that it is difficult to deduce physical properties of rock mass directly from seismic wave velocities, but the seismic wave velocity can be used as a tool to approximate rock mass properties because of weaker correlation between Vp and RMR with RQD. In addition, the velocity value of for soft and moderate rocks suggested by widely used construction standards is slower than that of the observed velocity, implying that the standards need to be examined and revised.

• Geophysics and Geophysical Exploration
• /
• v.4 no.1
• /
• pp.8-18
• /
• 2001

To delineate the inhomogeneities including fractures and to estimate the freshness of rock borehole radar consisting of the reflection and tomography methods, and GPR surveys were conducted at a granite quarry mine. The borehole reflection survey using the direction finding antenna was also conducted to get the spatial orientations of reflectors. 20 MHz was adopted as the central frequency for the borehole radar reflection and tomography surveys and 100 MHz was for GPR. Through the interpretation of borehole reflection data using dipole and direction finding antenna as well as GPR images, which are good agreement with each other, we could determine the orientation of the major fractures in three dimensional way. Parts of travel time curves of tomography data showed the anisotropy, which is uncommon in granite quarry. By comparing the tomography data and TeleViewer images, the anisotropy effect in this area are closely related to fine fissures aligned in the same direction. The area confined by the two fractures, MF2 and MF5, might consist of the most fresh granite in the surveyed area, which was concluded from the borehole radar tomography, and GPR images as well as the distribution of anisotropy.

• Geophysics and Geophysical Exploration
• /
• v.6 no.2
• /
• pp.57-63
• /
• 2003

For the dectection of small cavity in the hard rock, we investigated the feasibility of crosswell travel-time tomography and Kirchhoff migration technique. In travel-time tomography, first arrival anomaly caused by small cavity was investigated by numerical modeling based on the knowledge of actual field information. First arrival delay was very small (<0.125 msec) and detectable receiver offset range was limited to 4m with respect to $1\%$ normalized first arrival anomaly. As a consequence, it was turned out that carefully designed survey array with both sufficient narrow spatial spacing and temporal (<0.03125 msec) sampling were required for small cavity detection. Also, crosswell Kirchhoff migration technique was investigated with both numerical and real data. Stack section obtained by numerical data shows the good cavity image. In crosswell seismic data, various unwanted seismic events such as direct wave and various mode converted waves were alto recorded. To remove these noises und to enhance the diffraction signal, combination of median and bandpass filtering was applied and prestack and stacked migration images were created. From this, we viewed the crosswell migration technique as one of the adoptable method for small cavity detection.

• Tunnel and Underground Space
• /
• v.33 no.3
• /
• pp.109-125
• /
• 2023

Disposal repository for high-level radioactive waste secures its safety by means of engineered and natural barriers. The performance of these barriers should be tested and verified through various aspects in terms of short and/or long-term. KAERI has been conducting various in-situ demonstrations in KURT (KAERI Underground Research Tunnel). After completing previous experiment, a conceptual design of an improved in-situ experiment, i.e. K-COIN (KURT experiment of THMC COupled and INteraction), was established and detailed planning for the experiment is underway. Preliminary characterizations were conducted in KURT for siting a K-COIN test site. 15 boreholes with a depth of about 20 m were drilled in three research galleries in KURT and intact rock specimens were prepared for laboratory tests. Using the specimens, physical measurements, uniaxial compression, indirect tension, and triaxial compression tests were conducted. As a result, specific gravity, porosity, elastic wave velocities, uniaxial compressive strength, Young's modulus, Poisson's ratio, Brazilian tensile strength, cohesion, and internal friction angle were estimated. Statistical analyses revealed that there did not exist meaningful differences in intact rock properties according to the drilled sites and the depth. Judging from the uniaxial compressive strength, which is one of the most important properties, all the specimens were classified as very strong rock so that mechanical safety was secured in all the regions.

• Proceedings of the KOR-KST Conference
• /
• 1998.10b
• /
• pp.191-191
• /
• 1998

ITS를 구성하는 서비스나 기능이 대부분 동적인 특성을 지니고 있어, 앞으로는 이를 효율적으로 뒷받침할 수 있는 공간데이터(Spatial Data)가 필요하다. 특히, 대부분의 ITS서비스와 기능이 정보의 신속한 전달을 위해서 유무선통신을 사용할 것이다. 또한, 최정 사용자서비스와 응용분야가 공간데이터라는 기본적인 정보를 공유하므로써 위치에 대한 정적·동적교통정보를 제공받게 된다. 정보사용자가 사용하는 공간데이터가 상이하다면, 정보의 공유가 이루어지지 않거나 정확하게 제공되지 않는 것은 자명한 사실이다. 이러한 이유는 정보사용자가 자신들의 정보수집, 정보전달, 정보분석 등의 목적에 적합한 공간데이터를 제작하여 유지하기 때문이다. 결과적으로 정보의 공유를 위해서는 상이한 공간데이터들 간에 동일한 교통정보를 공유하도록 하는 조작이나 방법이 필요하다. 서로 다른 원본으로 구성된 데이터를 통합하고 이를 ITS서비스와 기능을 위한 각 시스템에 적용하기 위해서는 서로 다른 수준을 가지고 있는 공간데이터(수치지도 데이터)의 해상도, 위치정확도, 속성정확도, 정밀도, 범위 등과 같은 문제들이 최종 응용시스템에 적용되어져야 하고, 이를 통해 공간적인 위치와 수치지도를 구성하는 각종 엔터티가 참조되어야 할 것이다. 이뿐 아니라, 향후 데이터 공유의 방법에 있어서도, 각종 무선통신의 발달과 인터넷과 같은 정보전달매체의 대중화가 이루어짐에 따라, 정보의 공유가 동시적으로 이루어질 것이다. 본 연구에서는 공공기관주도로 제작된 전국범위의 수치지도를 하여, ITS용 네트워크데이터구성을 위한 기능분석과 사양을 제시를 함으로써, 이에 대한 프로파일 개발한다. 정보공유를 위한 위치참조모델(LRM)과 프로파일을 ITS데이터에 적용함으로써, 위치참조모델의 기능과 적용성을 평가한다.키기 위한 향후의 연구과제를 제시한다.Si결정의 크기를 비교하였을 때 45$\mu\textrm{m}$ 이하의 분말을 섞어 압출하였을 때 가장 작은 초정 Si입자 크기를 얻음 을 볼 수 있었다. 주의 Fairfax County에 소재한 주간 고속도로 66번(I-66)과 인접 교통망의 교통자료를 사용하여 각종 돌발교통 혼잡 상황을 전제로 한 Traffic Simulation과 정보제공시나\리오를 INTEGRATION Model을 이용해 실행하였다. 그 결과 적응형 알고리즘이 개개인의 최단시간 경로를 제공하는 사용자 평형 경로안내전략에 비해 교통혼잡도와 정체시간의 체류정도에 따라 3%에서 10%까지 전체통행시간을 절약할 수 있다는 결론을 얻었다.출발참, 구성대외개방선면축심, 실현국제항선적함접화국내항반적전항, 형성다축심복사식항선망; 가강기장건설, 개피포동제이국제기장건설, 괄응포동개발경제발전적수요. 부화개시일은 각 5월 26일과 5월 22일이었다. 11. 6월 중순에 애벌레를 대상으로 처리한 Phenthoate EC가 96.38%의 방제가로 약효가 가장 우수하였고 3월중순 및 4월중순 월동후 암컷을 대상으로 처리한 Machine oil, Phenthoate EC 및 Trichlorfon WP는 비교적 약효가 낮았다.>$^{\circ}$E/$\leq$30$^{\circ}$NW 단열군이 연구지역 내에서 지하수 유동성이 가장 높은 단열군으로 추정된다. 이러한 사실은 3개 시추공을 대상으로 실시한 시추공 내 물리검층과 정압주입시험에서도 확인된다.. It was resulted from increase of weight of single cocoon. "Manta"2.5ppm produced 22.2kg of cocoon. It

• Tunnel and Underground Space
• /
• v.14 no.6 s.53
• /
• pp.391-398
• /
• 2004

An algebraic algorithm for predicting the joint trace distribution on the cut-face of rock slope based on the orientations and the locations of joints investigated in the borehole has been developed. Joint trace prediction is manipulated by utilizing the three dimensional plane equations of both joint planes and projection face, and the extent of trace within the projection area is calculated by considering the persistence of each joint plane. Joint trace prediction method is efficiently applied for analyzing the stability and the adequacy of support design of Gimhae Naesam cut-slope, which is structurally unstable due to slumping. Structural characteristics of rock mass is investigated by performing DOM drilling and the potential rock mass sliding inside slope face is analyzed by examining the orientations of joint planes which can induce the slope failure. Also, the efficiency of anchor support design is evaluated by considering the joint trace distribution on the anchor installation area and its sliding potential.

• Tunnel and Underground Space
• /
• v.22 no.1
• /
• pp.43-53
• /
• 2012

Stability of cut-slope, the orientation and dimension of which are gradually changed, has been analyzed by employing the cross-section method capable of comprehensibly considering the lithological, structural and mechanical characteristics of slope rock. Lithological fragility is investigated by inspecting the drilled core logs and BIPS image has been taken to delineate the rock structure. Engineering properties of drilled-core including the joint shear strength have been also measured. Potential failure modes of cut-slope and failure-induced joints are identified by performing the stereographic projection analysis. Traces of potential failure-induced joints are drawn on the cross-section which depicts the excavated geometry of cut-slope. Considering the distribution of potential plane failure-induced joint traces blocks of plane failure mode are hypothetically formed. The stabilities and required reinforcements of plane failure blocks located at the different excavation depth have been calculated to confirm the applicability of the cross-section method for the optimum cut-slope design.

• Spatial Information Research
• /
• v.12 no.3
• /
• pp.275-283
• /
• 2004

In order to effectively, and accurately assess seawater intrusion in coastal area, multidisciplinary data including geophysical, well logging, and hydrogeochemical data should be managed in systematical way. Such systematical management of data is critical key to improve the re-usability of the data as well as the accuracy of the assessment by means of providing a method of synthetic analysis. Therefore, for systematical management of multidisciplinary data in seawater intrusion problem, we have developed a database management system and 3-D visualization interface based on geographic information system in this, study. All geophysical survey, well logging, hydrochemical, as well as drilling, data are classified as attribute data using Microsoft Access, and joined with spatial information based on ArcView. The database management system and 3-D visualization interface to handle these data, also, developed using the script language of ArcView. We think the development of database and 3-D visualization system will improve the efficiency of data management, user-friendliness of data access, and accuracy of data analysis.