• Economic and Environmental Geology
• /
• v.37 no.1
• /
• pp.143-151
• /
• 2004

This study focused on examining the possibility of recycling mine solid waste as environmental materials, especially for porous media. Basic properties including mineralogical compositions, chemical compositions, and particle size distribution of the tailings from the Sangdong W mine were checked. The mineralogical and chemical compositions of the tailings samples were not much different in depth. According to Korean Standard Leaching Test for Wastes(KSLT), concentrations of heavy metals leached from the tailings were below the standard values. As a result of particle size analysis, the median diameter (d$_{50}$) of the tailings was in the range of 10 to 30 ${\mu}{\textrm}{m}$. The stable tailings slurry made up of 3 ${\mu}{\textrm}{m}$ in d$_{50}$ was prepared using Attrition Mill. The milling condition was 40 vol% in slurry concentration, 700 rpm in stirring speed, and 1 hour in milling time. PEI was added as dispersing agent. Concentrated slurry was extended to 3 times by foaming method. In the case of 3 times foamed slurry, the total and open porosity of ceramic supports sintered at 1,075$^{\circ}C$ for 90 minutes was about 80% and 72%, respectively. Pore size was in the range of 30∼350${\mu}{\textrm}{m}$. Therefore, the tailings could be recycled starting material for environmental materials such as macroporous ceramic support.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.211-211
• /
• 2013

Ru-Cr은 차세대 반도체 메모리(RAM, MRAM, FeRAM), 헤드(MR, TMR), 캐피시터의 웨이퍼 등에 전극층이나 시드층 형성을 위해 스퍼터링 타겟으로 제조되며, IT산업이 발달함에 따라 수요가 증가하고 있다. 기존의 스퍼터링 타겟은 산처리와 주조와 같은 습식법이 주를 이루었으나, 긴 제조시간과 강산사용의 위험성화 강산폐유의 처리가 문제되고 있다. 최근에는 습식공정을 보완하기 위한 건식법의 연구가 진행 중이며, 합금소재에 대한 건식법의 연구가 필요하다. 본 연구에서는 폐 Ru-Cr 금속합금 스퍼터링 타겟을 Hammer-mill, jet-mill 등 건식으로 분쇄하고 RF-Plasma를 이용하여 소결에 용이한 구형, 고순도 Ru-Cr금속합금분말을 제조하였다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.148-148
• /
• 2003

질석(vermiculite)을 출발물질로 하여 30$0^{\circ}C$에서 4시간 열처리하여 습식분쇄하고 325mesh 이하의 입자를 선별하여 수열조건에서 양이온 계면활성제인 hexadecyl trimethylammonium bromide (C$_{16}$TABr)를 층간 삽입시켜 유기화 질석을 제조하였다. 생성물을 XRD, TGA, FT-IR 등을 이용하여 분석하였고, 합성 및 층간 삽입조건을 조사하였다. 질석에 $C_{16}$TABr를 층간 삽입을 확인하기 위하여 XRD 분석 결과 d-spacing 값이 9.6$\AA$에서 33.5$\AA$으로 증가됨을 확인하였고, 열중량 시험결과 출발물질과 비교하여 유기화 질석은 25%감량이 확인되었다. 위 결과 값으로부터 질석의 유기화 처리로 인하여 층간 간격이 확장되었음을 확인하였다. 일반적으로 층간 간격이 넓을수록 고분자가 층 사이에 보다 쉽게 삽입될 수 있으며 고분자 매트릭스 안에서 층상화합물의 분산 및 박리가 용이해진다. 따라서 본 연구 결과로부터 합성된 유기화 질석은 고분자 나노복합재로 사용 가능성을 제시하고 있다.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.10a
• /
• pp.17-18
• /
• 2008

접착물질인 PP(Polypropylene)가 함유되지 않은 섬유 폐기물을 Niagara beater을 이용한 습식 분쇄하여 판상형태의 Sheet에 접착물질인 KSL 103과 KSL 203을 물과 1:1로 혼합사용 분무한 제품의 경우가 굴곡휨강도, 인열강도가 우수하였고, PP의 사용의 배제로 Press시의 온도를 $180^{\circ}C$에서 $130^{\circ}C$로 낮추어 작업이 가능하고 Texon에서 부여하기 힘든 굴곡휨강도와 굴곡강도가 우수한 결과를 나타내었다.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.514-519
• /
• 2020

Graphite materials for lithium ion battery anode materials are the most commercially available due to their structural stability and low price. Recently, research efforts have been conducted on carbon coatings by improving side reactions at the edge site of carbon materials. The carbon coating process has classified into a CVD by chemical reaction, wet coating process with solvent and dry coating by mechanical impact. In this paper, the rapid crush/coating process was used to solve the problem of which only few parts of the carbon precursor (pitch) can be used and also environmental problems caused by solvent removal in the wet coating process. When the ratio of needle coke to pitch was 8 : 2 wt%, and the rapid crush/coating process was carried out, it was confirmed that the fracture surface was coated by pitch. The pitch-coated sample was treated at 2400 ℃ and 41.8% improvement in 10C/0.1C rate characteristic was observed. It is considered that the material simply manufactured through the simple crush/coating process can be used as an anode electrode material for a lithium ion battery.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.12
• /
• pp.1797-1801
• /
• 2011

Two brown rice samples differing in amylose content, 20.1 (normal) and 7.3% (low amylose) were milled by different milling methods, and their physicochemical properties were tested. Particle size of brown rice flour prepared by dry milling using a pin mill (DM) was lower than that prepared by wet milling using a roll mill (WM). Particle size was further reduced by successive dry milling of the flour after wet milling and drying (WM/DM). Damaged starch contents in the wet milled brown rice flour were 14.6 and 15.6% for the normal and low amylose samples, respectively, whereas they were only 4.2 and 4.8% for the dry milled samples. WM/DM method resulted in a lower damaged starch (%) than DM, despite a reduced flour particle size. Water absorption index (WAI) of the brown rice flour was the lowest after WM/DM, and the water solubility index (WAI) was higher in the order of DM, WM/DM, and WM. Brown rice flour with normal amylose content appeared to have significantly higher pasting viscosities, as determined using a Rapid Visco Analyzer (RVA). Compared to dry milled brown rice flour, wet milled brown rice flour showed lower peak viscosity and higher final viscosity, resulting in increased setback value.

• Applied Chemistry for Engineering
• /
• v.27 no.4
• /
• pp.371-379
• /
• 2016

In this article, the foamed body of glass was manufactured from the waste borosilicate glass produced by wet pulverization process without additional pretreatment which can be used as a recycling method for waste LCD panel glass. Each 100 g of pulverized waste borosilicate glass with the size of less than 270 mesh were mixed with 0.3 weight fraction of carbon and 1.5 weight fraction of $Na_2CO_3$, $Na_2SO_4$ and $CaCO_3$ and let them foamed for 20 minutes at $950^{\circ}C$ to manufacture the foamed body having the density of less than $0.3g/cm^3$. Additionally, adding $SiO_2$ or $H_3BO_3$ to the mixture enabled the foamed body to have efficient formation of open pores which showed the possibility for producing the foamed body with new functionalities such as sound absorption.

• Resources Recycling
• /
• v.33 no.2
• /
• pp.24-36
• /
• 2024

The lithium-ion battery recycling process has been classified into direct recycling, hydrometallurgical process, and pyrometallurgical process. The commercial process based on the hydrometallurgical process produces black mass through pretreatment processes consisting of dismantling, crushing and grinding, heat treatment, and beneficiation, and then each metal is recovered by hydrometallurgical processes. Since all lithium-ion battery recycling processes under development conducts hydrometallurgical processes such as leaching, after the pretreatment process, to produce precursor raw materials, this article suggests a classification method according to the pretreatment method of the recycling process. The processes contain sulfation roasting, carbothermic reduction roasting, and alloy manufacturing, and the economic feasibility of the lithium-ion battery recycling process can be enhanced using unused by-products in the pretreatment process.

• Journal of the Mineralogical Society of Korea
• /
• v.18 no.1
• /
• pp.19-31
• /
• 2005

A study on the beneficiation of illite occurring in Youngdong province is performed with applying selective grinding and air classification techniques. Quartz and illite are occurred as major components, and sulfide minerals such as pyrite, chalcopyrite are associated as minor components. The result of sieving test shows that contents of Al₂O₃, K₂O and ignition loss are increased, whereas SiO₂ is decreased with particle size decrease. Fe₂O₃ content is almost same in all the particle size range but slightly lower at coarse particles. The yield of fine particles is increased with increasing rotor speed in both grinding stage and air classification stage. When the selective grinding and air classification are carried out at optimal condition, yield of the concentrate is 76.16 wt.%. The chemical compositions of the concentrate are SiO₂70.13%, Al₂O₃ 19.40%, Fe₂O₃ 1.62%, K₂O 5.20%, and ignition loss 2.77%. The beneficiation process developed in the current study is very effective method which purification and particle size control can be achieved simultaneously.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.115.2-115.2
• /
• 2010

최근 유가 상승 및 에너지 확보, 경질 원유 생산량 및 부존량 감소로 인하여 대체 석유자원의 개발에 대한 연구 및 관심이 급증하고 있다. 기존의 연소 방식이 아닌 연료를 청정 가스로 전환하여 이용하는 가스화 기술 개발이 진행되고 있다. 석탄은 매장량이 세계적으로 풍부 할뿐만 아니라, 지역적으로도 편재되어 있지 않은 에너지원인 석탄을 활용하는 새로운 발전기술로 환경보전성이 우수하며, 효율이 기존의 발전 시스템보다 뛰어난 에너지 이용기술로 각광받는 분야이다. 석탄 슬러리는 분쇄한 석탄을 믹서를 사용하여 소량의 계면활성제를 첨가하여 제조한다. CWM 제조용 석탄은 대체로 고유수분 5%이하, 회분 10%이하의 석탄이 추천되고 있으며, 수분이나 회분량, 산소함량, 입자의 세공율이 증가할수록 고농도화에 불리한 것으로 나타나고 있다. 연료적 가치를 향상시키기 위해서는 물의 함량을 적게, 즉 석탄의 농도를 증가시키는 것이 중요하다. 일반적인 CWM 규격으로는 석탄농도 65% 이상이 바람직한 것으로 보고되고 있다. 석탄가스화에 연료로 사용되는 CWM의 연료성상 및 미립화 정도, 제조 조건 등에 따라 많은 차이가 발생한다. 본 실험에서는 1.0T/D급 습식 분류층가스화기에서 이용할 CWM의 제조를 위하여 소형 믹서를 이용하여 석탄의 농도에 따른 점도 변화와 석탄의 분쇄입자 크기에 따른 점도 변화, 계면활성제와 첨가제의 농도에 따른 점도 특성을 실험하였다.