• Journal of the Korean Geotechnical Society
• /
• v.34 no.6
• /
• pp.49-59
• /
• 2018

When a tracked vehicle travels off-road, shearing action and ground sinkage occur on the soil-track interface and severely affect tractive performance of the tracked vehicle. Especially, the ground sinkage, which is induced by vehicle's weight (hereinafter referred to as static sinkage) and longitudinal forces in the direction of travel producing slip (hereinafter referred to as slip sinkage), develops soil resistance, directly restricting the tractive performance of an off-road tracked vehicle. Thus, to assess the tractive performance of an off-road tracked vehicle, it is imperative to take both of static sinkage and slip sinkage into consideration. In this research, a series of model track experiments was conducted to investigate the slip sinkage which has not been clarified. Experiment results showed that the slip sinkage increased with increasing the slip ratio, but the increasing rate gradually decreased. Also, the slip sinkage was found to increase as relative density of soil decreased and imposed vertical load increased. From the experiment results, the normalized slip sinkage defined as slip sinkage to static sinkage calculated in the identical condition was investigated, and an empirical equation for the slip sinkage was developed in terms of slip ratio, which allows vehicle operators to predict the slip sinkage in a given soil and operating conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.234-243
• /
• 2002

When a vehicle is operated over sort terrain, torque(or soil thrust) applied to driving wheel brings about shear displacement far soil due to compression and shear failure of soil under tire. This shear displacement give rise to slip and a additional sinkage due to slip. This additional sinkage is usually referred to as slip-sinkage. The slip-sinkage is affected by soil conditions and inflation pressure of tire. This slip-sinkage influence tractive performance on driving wheel . We conducted the experimental study far investigating the effect of slip on sinkage and tractive performance of driving wheel, such as motion resistance, thrust and drawbar pull. The experiment was carried out over three different soil conditions(soft, hard and very hard soil) far a tire with three levels of inflation pressure(120kPa, 240kPa and 360kPa). The results of this study show qualitatively slipsinkage characteristics and slip-tractive performance relationships of driving wheel with soil conditions and inflation pressure of tire.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.2
• /
• pp.123-134
• /
• 2001

본 연구에서는 화강풍화토 지반상 unpropped diaphragm wall의 거동을 연구하기 위하여 벽체의 근입깊이와 지하수위 조건을 변화시키면서 원심모형실험을 수행하였다. 원심모형실험시 diaphragm wall은 두께 8mm인 알루미늄합금을 사용하였으며, 지반굴착을 재현하기 위하여 zinc chloride 기법을 이용하였다. 수치해석은 대부분의 지반공학문제에 적용할 수 있는 SAGE CRISP 프로그램을 이용하였다. 수치해석에서 모형지반은 수정 Cam-Clay 모델, diaphragm wall은 탄성모델, 지반과 diaphragm wall 사이의 경계면요소는 슬립모델을 사용하여 2차원 평면변형률 조건으로 해석을 수행하였다. 모형실험 결과 파괴면의 직선적인 형태로 파괴면내의 배면측 지반은 벽체를 향하여 하향의 변위를 일으키면서 벽체의 회전에 의해 파괴되었다. 실험 및 유한요소해석 결과 지반의 최대침하량과 최대침하량이 발생하는 위치는 잘 일치하였으며, 깊이에 따른 벽체변위는 선형적인 관계를 나타내었다. 또한, 최대 휨모멘트와 근입깊이로 정규화한 최대 휨모멘트 발생위치($h_{Mmax}$/d=0.4)는 잘 일치하였다.

• Journal of Biosystems Engineering
• /
• v.34 no.4
• /
• pp.205-210
• /
• 2009

It has been known from Willoughby's empirical equation that rating cone index can be determined if wheel sinkage and slip of a vehicle can be measured on soil surface. A field data of wheel sinkage and slip was collected from two tractors of different sizes on gravelly sand and gravelly loamy sand. Using the data, rating cone index of the soil was estimated. The estimated rating cone index demonstrated that it could be determined in real time by measuring wheel sinkage and slip. It was also demonstrated statistically that the same soil strength could be obtained under the same soil conditions regardless of the vehicle platforms used for the wheel sinkage and slip measurements.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.116-120
• /
• 2003

To study the trafficability on soft and cohesive benthic terrain, a tracked vehicle model($670mm(L){\times}750mm(B_c)$) is designed and tested. The pitch and chevron angle of grouser, weight and center of gravity of vehicle, and drawbar pull force are chosen as experimental variables. Slip, sinkage and inclined angle of vehicle are picked as performance values. Strength of soil is considered as noise factor. A preliminary straight-line motion test is performed. Then, DOE(Design of Experiment) is discussed for further research.

• Journal of Biosystems Engineering
• /
• v.25 no.5
• /
• pp.359-368
• /
• 2000

In this paper, mathematical model was developed for predicting the tractive performance of off-road wheeled vehicles operated on soft terrains. Based on the mathematical model, a computer simulation program(TPPMWV) was developed. The model takes into account main design parameters of wheeled vehicle, including radius and width of front and rear tire, weight of vehicle, wheelbase and driving type(4WD, 2WD). Soil characteristics, such as the peressure-sinkage and shearing characteristics and the response to repetitive loading and slip-sinkage effect, are also taken into consideration. The effectiveness of the developed model was verified by comparing the predicted drawbar pulls using TPPMWV with measured ones obtained by field tests for two different driving types of wheeled vehicle. As a results, the drawbar pulls predicted by the TPPMWV were well matched to the measured ones within the absolute errors of 3.916%(4WD) and 13.31%(2WD) for two different driving types, respectively.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.5
• /
• pp.19-26
• /
• 2014

Concrete guide rail and median barrier are an attached RC member, however they are vulnerable to cracking due to slip form construction and large surface of member. In this study, causes and pattern of cracking are analyzed through assessment and NDT (Non-Destructive Technique) evaluation for concrete guide rail and median barrier on highway structure. For this work, analysis on drying shrinkage and hydration heat are performed considering installation period, and plastic shrinkage is also analyzed considering their environmental conditions. From the evaluation, plastic settlement around steel location, drying/ plastic shrinkage, and aggregate segregation are inferred to be the main causes of cracking in the structures. The crack causes and patterns are schematized and techniques of crack-control are suggested. Furthermore concrete guide rail/ median barrier in the bridge on the sea are vulnerable to cracking at early age so that special attentions should be paid at the stages of material selection and construction.

• Proceedings of the KSRS Conference
• /
• 2008.03a
• /
• pp.3-6
• /
• 2008

본 논문에서는 레일형 GB-SAR의 단점을 극복하고자 차량에 원형레일을 탑재하여 신속한 기동을 확보하고 합성구경의 길이를 늘리며 영상영역을 확장한 Arc-SAR의 설계안을 제시한다. 하드웨어 측면에서 살펴보면, 밴형 차량의 상부에 원형레일을 설치하고 마이크로파 송, 수신 안테나를 탑재한 후 레일 위를 1mm 이내의 정밀도로 이동시키며, 자료를 획득하게 된다. 이때 안테나에 연결된 동축 케이블은 차량 내부의 송, 수신장치에 연결되는데 RF대역에서 완벽히 작동하는 슬립링이 없기 때문에 내부 송, 수신 장치를 턴 테이블위에 장착하여 외부 안테나의 이동과 동일한 각도로 회전하여, 동축 케이블의 꼬임을 방지하게 된다. 송, 수신 장치의 구성은 벡터 네트워크 분석기를 기반으로 마이크로파 앰프, 마이크로파 스위치로 구성되며, 통합 제어 소프트웨어를 통해 외부 안테나의 이동과 함께 제어된다. 한편, Arc-SAR 영상의 구현은 원형레일을 따라 얻어지는 합성구경의 기하학적인 특수성을 감안하여 최초로 시도될 것이다. 이 시스템은 RTK-GPS를 장착하여 지반변형 모니터링 시 차량 이동 오차를 최소화 하고자 하며, 이외에 고정형 산란체를 이용하여 차량 이동 오차를 보정하고자 한다. 또한 AWS (Automatic Weather System)을 장착하여 위상의 대기보정을 동시에 수행할 것이다. 이 시스템은 차량 탑재에 의한 기동성의 확보로 침수나 침하 등 긴급 재난 지역에 즉각적인 대응이 가능하며, 대형 구조물의 주기적인 변형 모니터링 등에 활용성이 클 것이다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.4
• /
• pp.693-703
• /
• 2017

Rover wheel's mobility depends on soil's condition and wheel's design. The purpose of this study is to evaluate the effect of soil conditions, which are Jumunjin sand and Korean lunar soil simulant (KLS-1), on wheel's motion performance. The experiments were performed by using a single wheel testbed with a wheel which grouser height is 15mm on Jumunjin sand and KLS-1, respectively. Also the influence of grouser length to wheel's mobility performance was studied. The experimental results of torque, drawbar pull and sinkage relating to slip ratio were discussed and analyzed to evaluate wheel's motion performance. Results showed wheel moving on KLS-1 has high performance than Jumunjin sand. Wheel's mobility performance was influenced by soil's properties of cohesion and frictional angle. In addition, wheel's performance of drawbar pull and Torque increased with the increasing of grouser length.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.11
• /
• pp.97-108
• /
• 2016

Lunar rover plays an important role in lunar exploration. Especially, performance of rover wheel related to interaction with lunar soil is of great importance when it comes to optimization of rover's configuration. In this study, in order to investigate the motion performance of lunar rover's wheel on Korean Lunar Soil Simulant (KLS-1), a single wheel testbed was developed and used to carry out a series of experiments with two kinds of wheel with grousers and without grousers which were used to perform the experiments. Wheel traction performance was evaluated by using traction parameters such as drawbar pull, torque and sinkage correlated with slip ratio. The results showed that the single wheel testbed was suitable for evaluation of the performance of wheel and rover wheel with grousers which was likely to have higher traction performance than that without grousers in Korean Lunar soil simulant. The experimental results could be utilized in verification of the optimum wheel design and effectiveness of wheel traction for Korean lunar rover.