• Journal of the Korean Society for Railway
• /
• v.9 no.6 s.37
• /
• pp.798-803
• /
• 2006

The suspension elements like primary coil spring, yaw damper, body to body damper are core parts of high speed railway bogie and the faults relating to these elements are reported recently. Thus, this study is started to analyze the displacements characteristics of suspension elements of high speed railway rolling-stock for the purpose of preventing the faults and developing the maintenance technology for suspension elements like spring and dampers. For this purpose, we made a plan to measure the displacements of the primary coil spring, yaw damper and body to body damper in actual running condition. We developed the measurement device to measure the longitudinal displacement and angular displacement of suspension elements and installed this device to test suspension elements. Test to measure displacements of suspension elements is conducted in service line of high speed railway. The displacement data which is acquired from the test with actual vehicles was analyzed for its maximum displacement depending on the track sections. As a result of analysis, we obtained the displacement trends occurring with the sections and valuable results like maximum values and the displacement distribution.

• Journal of computational fluids engineering
• /
• v.19 no.2
• /
• pp.99-107
• /
• 2014

The aim of the present study is to investigate the flow interference between two adjacent undulating fish-like body, and its effect on the undulating propulsion. For this purpose, unsteady two dimensional incompressible flow calculations were conducted using an unstructured mesh flow solver, coupled with an overset mesh technique. To deal with mesh deformation due to fish locomotion, spring analogy is utilized. The fish body used in the simulation is constructed from the NACA0012 airfoil. The study indicates that the propulsion of undulating fish is proportional to frequency and wavelength of the midline oscillation when there is no adjacent fish. It also reveals that average thrust was increased when the vortex shedding from the tail was conserved well and pressure difference between upper and lower sides of the fish was magnified due to flow interference. From this study, which relative position and phase difference of locomotion between two fishes can generate maximum thrust was known among six different cases.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.9 no.3
• /
• pp.21-30
• /
• 1989

In this study, the dynamic behavior of a continuous bridge under moving load is studied considering roughness of the road surface. Vehicle model includes the spring effects of axes, and due to these effects, equations of motions for the vehicle and bridge are derived in coupled form. And then iteration method is used to solve the equations. In experimental study a bridge model is constructed considering the similarity rule in order that the model exhibits dynamic behavior similar to that of prototype. Three types of roughness such as uneven random roughness, uplift on the approach and piece-wise constant roughness are used to describe road roughness. Through the numerical analysis and experiments, the effects of surface roughness, sprung mass, and velocity on the dynamic behavior of the bridge are examined.

• Journal of Power System Engineering
• /
• v.14 no.3
• /
• pp.33-38
• /
• 2010

Technology of vehicle industry has been developing and it is required a better vehicle performance than before. Therefore, the consumers are asking not only an economic efficiency, functionality, polished design, ride comfort and silence but also a driving stability. The ride comfort, silence and driving stability are influenced by the size of vehicle and various facilities. But the principal factor is a room noise and vibration sensed by a driver and passenger. Thus, the NVH of vehicle has been raised and used as a principal factor for evaluation of vehicle performance. The primary objective of this study is an optimized design of powertrain mounting system. To optimized design was applied MSC.Nastran optimization modules. Results of dynamic analysis for powertrain mounting system was investigated. By theses results, design variables was applied 12 dynamic spring constant. And the weighting factor according to translational displacement and rotational displacement applied 3 cases. The objective function was applied to minimize displacement of powertrain. And the design variable constraint was imposed dynamic spring constant ratio. The constraint of design variable for objective function was imposed bounce displacement for powertrain.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.1
• /
• pp.145-153
• /
• 2007

The purpose of this study is to compare and analyze the phase-by-phase elapsed time, the COG, the body joint angle changes and the angular velocities of each phase of Handspring Salto Forward Piked performed by 4 college gymnasts through 3D movement analysis program. 1. The average elapsed time for each phase was .13sec for Phase 1, .18sec for Phase 2, .4sec for Phase 3, and .3sec for Phase 5. The elapsed time for Phase 1 to Phase 3 handspring was .35sec on average and the elapsed time for Phase 4 to Phase 5 handspring salto forward piked was .7sec on average. And so it showed that the whole elapsed time was 1.44sec. 2. The average horizontal changes of COG were 93.2 cm at E1, 138. 5 cm at E2, 215.7 cm at E3, 369.2 cm at E4, 450.7 cm at E5, and 553.1 cm at E6. The average vertical changes of COG were 83.1 cm at E1, 71.3 cm at E2, 78.9 cm at E3, 93.7 cm at E4, 150.8 cm at E5, and 97.2 cm at E6. 3. The average shoulder joint angles at each phase were 131.6 deg at E1, 153.5 deg at E2, 135.4 deg at E3, 113.4 deg at E4, 39.6 deg at E5, and 67.5 deg at E6. And the average hip joint angles at each phase were 82.2 deg at E1, 60 deg at E2, 101.9 deg at E3, 161.2 deg at E4, 97.7 deg at E5, and 167 deg at E6. 4. The average shoulder joint angular velocities at each phase were 130.9deg/s E1, 73.1 deg/s at E2, -133.9 deg/s at E3, -194.4 deg/s at E4, 29.4 deg/s at E5, and -50.1 deg/s at E6. And the average hip joint angular velocities at each phase were -154.7 deg/s E1, -96.5 deg/s at E2, 495.9 deg/s at E3, 281.5 deg/s at E4, 90.3 deg/s at E5, and 181.7 deg/s at E6. The results shows that, as for the performance of handspring salto forward piked, it is important to move in short time and horizontally from the hop step to the point to place the hands on the floor and jump, and to stretch the hip joints as much as possible after the displacement of the hands and to keep the hip joints stretched and high in the vertical position at the takeoff. And it is also important to bend the shoulder joints and the hip joints fast and spin as much as possible after the takeoff, and to decrease the speed of spinning by bending he shoulder joints and the hip joints quickly after the highest point of COG and make a stable landing.

• The Journal of the Convergence on Culture Technology
• /
• v.5 no.3
• /
• pp.147-154
• /
• 2019

Baseball was first introduced in Korea by American Gillette, who was the general manager of the YMCA in the late Joseon Dynasty. There are many discussions about the timing of the first baseball game in Korea, but it has yet to be sorted out. But what is certain is that baseball was introduced directly from the after 1903, when the first Korea YMCA, the Hwang seong Christian Youth Association, was founded. Gillett studied at Springfield YMCA International Training School in the United States from 1900 to 1901. The school is where Gulick worked as a teacher, who actively embraced strong Christianity from Britain and laid the foundation for the YMCA project in the United States. Therefore, Gillett was influenced by this Muscular Christianity, and the reason behind the introduction of baseball in our country is the same Muscular Christianity idea. Gillett, the manager of the YMCA in Korea, has developed various sports projects in Korea based on this Manager idea. It also helped the Korean people, who have been under Japanese colonial rule since 1905, to strengthen their bodies and minds and It helped the independence movement of Koreans. These specific and practical examples are YMCA baseball team active and the 105-member incident.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.2
• /
• pp.49-63
• /
• 1989

Wave drift forces which are small in magnitudes compared to the first order wave exciting forces can cause very large motion of a vessel in waves. In this paper a theoretical and experimental analysis is made of the mean and slowly varying wave dirft forces on the semi-submersible platform. Theoretical calculations are performed by using near field method with three dimensional diffraction theory and model tests are carried out in regular and irregular waves with a 1/60 semi model. Test results are compared with theoretical calculations and the mooring spring effects in the test are discussed.

• Journal of the korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.23-32
• /
• 1996

차량에서 엔진은 가장 큰 질량 집중체(concentrated mass)이다. 만약 엔진이 적절하게 구속되지 않거나 절연되어 있지 않으면, 차체에 진동을 일으키는 원인이 된다. 엔진은 다양한 진동 교란을 받는데 엔진 마운트는 이러한 모든 것들을 고립시키는 역할을 해야 하며, 엔진은 정적인 장착 하중에 대한 지지와 전후, 좌우 및 수직 방향의 운동에 대해 적절한 강성을 가져야 한다. 또한 정숙성을 향상시키기 위해서는 엔진 마운트의 재료인 고무의 강성계수를 낮추는 것이 필요한데 이는 일반적으로 내구성의 저하를 가져온다. 따라서 개발과정에서 강성계수를 낮추는 변경을 하면 부품의 내구성을 보정함에 따르는 재평가 또한 필요하게 된다. 엔진 마운트에 쓰이는 고무부품의 해석은 엔진 마운트 시스템에 대한 진동 해석 및 내구수명의 예측과 병행해야 하며, 진동해석으로부터 얻은 하중 지지 능력 등의 모든 요구 특성을 만족하기 위해서는 고무 재료의 특성에 대한 지식, 엔진 마운트의 장착 위치에 대한 결정 능력과 함께 주어진 조건에 대한 형상의 최적 설계 능력 등이 요구된다. 본 연구에서는 기본적인 형상을 파라미터화하여 엔진 마운트의 형상을 최적화 하는 절차를 제안하였다. 현재 승용차에 널리 사용되고 있는 부시형(bush type) 엔진마운트를 적용 모델로 선택하였으며, 엔진 마운트의 기본적인 형상을 몇개의 파라미터를 사용하여 정의하고 설계 사양으로 주어지는 강성값과 각 파라미터들의 조합으로 구성되는 형상이 갖는 강성값의 차이가 최소가 되도록 파라미터 값들을 최적화하였다. 최적화된 파라미터 값들로 구성되는 형상을 내구 성능, 성형성등을 고려하여 최종 형상으로 결정한다. 내구성능의 예측은 금속부품의 내구수명 예측에 널리 이용되고 있는 방법이 방진 고무부품의 경우에도 적용 가능한지를 검토하고, 방진 고무부품에도 일반적으로 적용될수 있는 내구수명 예측방안의 개발 가능성을 타진해 보았다. 본 연구의 목표는 시제품을 제작하기 이전에 설계된 부품에 대한 스프링 상수 및 내구특성을 체계적으로 규명하여 제품 시험의 횟수를 줄이고, 보다 정밀한 제품을 제작할 수 있도록 하기 위한 것이다.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.3
• /
• pp.397-404
• /
• 2011

In this paper, a research for the dynamic wheel loads of a 3D vehicle model, which relates to a tire-enveloping model, is carried out. A single truck with four axles is modeled as a 10-D.O.F. vehicle by modeling both contact length of tires and pitching of tandem spring axles. The dynamic equations of the vehicle are obtained using the Lagrange's equation, the solution of the equations is calculated by Newmark-${\beta}$ method. The validity of the developed 3D vehicle model is demonstrated by comparing results obtained from the proposed method with those from experimental data. The maximum impact factors of tire force are evaluated according to the various step bumps on which a 24-ton dump truck is running.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.1
• /
• pp.95-104
• /
• 2002

In this paper, research for dynamic wheel loads of 3-D vehicle model considering tire enveloping model is carried out. Heavy trucks with 2-axles and 3-axles are modeled by 7-d.o.f. and 8-d.o.f., in which contact length of tire and pitching of tandem spring axles is considered. Dynamic equations of vehicle are derived by using the Lagrange's equation and solution of the equation is calculated by 5th Runge-Kutter method. The validity of the developed 3-D vehicle model is demonstrated by comparing the results obtained by the present method and experimental data by Whittemore. The maximum impact factors of tire force are calculated when vehicle models of 8ton and 15ton dump truck are running on the different class roads with 1.0km and on the various step bump.