• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.167-167
• /
• 2008

The barium strontium calcium titanate powders were prepared by sol-gel method. Ferroelectric $(Ba_{0.54}Sr_{0.36}Ca_{0.1})TiO_3$(BSCT) thick films were fabricated by the screen-printing method on alumina substrate. And we investigated the structural and dielectric properties of BSCT thick films with the variation of sintering temperature. As a result of thermal analysis, BSCT polycrystalline perovskite phase was formed at around $660^{\circ}C$. The results of X-ray diffraction analysis were showed a cubic perovskite structure without presence of the second phase in all BSCT thick films. The average grain size and the thickness of the specimen sintered at $1450^{\circ}C$ were about 1.6 mm and 45 mm, respectively. The relative dielectric constant increased and the dielectric loss decreased with increasing the sintering temperature, the values of the BSCT thick films sintered at $1450^{\circ}C$ were 5641 and 0.4% at 1kHz, respectively.

• Phonetics and Speech Sciences
• /
• v.5 no.3
• /
• pp.63-69
• /
• 2013

The purpose of this study was to evaluate the maximum and optimal listening speed of Korean TTS for the blind. Five blind participants took part in this study. The instruments used in this study were 17 sentence sets (2 sets for an excercise, 10 sets for a repeated test, and 5 sets for a random test), with short meaningful sentences (the same sentences for the repeated test, different sentences for the random test) with 15 differentiated speeds (Range=0.8-3.6, SD=0.2). Each participant's maximum and quickest listening speeds were calculated by objective recall accuracy (determined by the number of correctly recalled syllables/the total number of syllables in a sentence X 100) and subjective recall accuracy (recall accuracy judged by each participant's subjective evaluation). The results showed that the participants' recall accuracy had a tendency to increase as the TTS speed decreased. Participants' subjective recall accuracy was higher than objective recall accuracy in the repeated tests and vice versa in the random tests. The results also revealed that the participants' sentence familiarity had an influence on their Korean TTS listening speed.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2006.11a
• /
• pp.265-268
• /
• 2006

데스크탑 환경의 멀티미디어 디스플레이 시스템은 고해상도, 대화면의 영상을 제공해 줄 수 있는 반면 제약된 공간에서만 동작하므로 휴대할 수 없는 문체가 있다. PDA, PMP와 모바일 폰과 같은 휴대성을 가지는 멀티미디어 디스플레이 시스템은 해상도가 낮아 사용자에게 충분한 몰입감을 제공 해 주지 못한다. 본 논문에서는 기존의 데스크탑 환경에서 동작하는 프로젝션 기반의 증강현실 시스템을 모바일 플랫폼으로 확장한 프로젝션 기반의 휴대형 멀티미디어 디스플레이 시스템을 제안한다. 제안된 시스템은 PDA와 포켓 프로젝터를 결합한 것으로, PDA에서 전 처리된 멀티미디어 영상을 포켓 프로젝터를 이용하여 임의의 모양을 가지는 스크린에 왜곡 없이 영상을 표시해 줄 수 있다. 개발환경은 Window Mobile 5.0 기반의 ARM 플랫폼을 사용하는 PDA를 이용하였고, 시스템의 최적화를 위하여 x86 플랫폼에 최적화된 OpenCV 라이브러리를 모바일용으로 변환하였다. 또한 모바일 플랫폼에서는 부동소수점 연산으로 인한 시스템의 속도저하 문제가 발생하기 때문에 부동소수점 연산을 정수 연산으로 변환함으로써 처리 속도를 개선하였다. 프로젝션 기반의 디스플레이 시스템을 실현하기 위해서 필요한 기술적인 과제들을 모바일 환경에서 직접 처리해 봄으로써 휴대형 프로젝션 기반의 멀티미디어 시스템의 가능성을 제시한다.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.4
• /
• pp.149-154
• /
• 2011

Martensitic stainless steel STS 431 has been nitrided by active screen ion nitriding under the various temperature and time. The thickness of diffusion layer, case depth, hardness and composition phases were investigated using field emission scanning electron microscopy (FE-SEM), micro-Vickers hardness tester, X-ray diffraction (XRD) and glow discharge spectroscopy (GDS). It was observed that the thickness of diffusion layer depends strongly on the treatment temperature and time. A sample, which was nitrided at $450^{\circ}C$ for 8hours, was a maximum hardness of Hv0.01 1558 and nitride layer of $70{\mu}m$. As shown in XRD patterns, $\varepsilon(Fe_{2-3}N)$ and expanded martensite (${\alpha}_N$) phases which was saturated with nitrogen solid solution were in the nitrided layer treated at $450^{\circ}C$ for 2 hours. Composition phases of $\varepsilon$ $(Fe_{2-3}N)$ and ${\gamma}'$ ($Fe_4N$) were observed after active screen nitriding at $450^{\circ}C$ for 8 hours.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.6
• /
• pp.505-511
• /
• 2014

In this paper, silver pastes were printed on polyethylene terephthalate (PET) film using screen printing and evaluated the drying characteristics by using dry oven and NIR drying system. The printed Ag films were dried at $140^{\circ}C$ and the drying time was changed from 10 to 90 seconds. To evaluate the electrical properties of printed Ag film, sheet resistance was compared. The sheet resistance of the dried thin silver film by using NIR drying system more rapidly decreased. To clarify this phenomena, the morphology and component of the dried surfaces were measured by using the scanning electron microscope (SEM) and the energy dispersive X-ray Spectroscopy (EDX), respectively. In the EDX measurement results, the oxidation of the surface was observed in the dried thin film by using the dry oven. The NIR drying system is more applicable than conventional hot air drying to apply continuous printing system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.351-354
• /
• 1998

The formation of the $YBa_2Cu_30_{7_\delta}$(Y123) thick films has been investigated by a surface diffusion Imcess between $3BaCu0_2$+2CuO composite coating powder and a $Y_2BaCuO_5$(Y211). This reaction has been studied in the temperature of $930^{\circ}C$ and $940^{\circ}C$ for 2h to 10h in an oxygen atmosphere. The Y211 substrates becomes covered by co-precipitation of Y123 grains and CuO inclusions. X-ray diflractotnctn. revealed that the lager consisted of an orthorhombic crystal structure. The maximum Jc of $400A/\textrm{cm}^2$ is abtained when the specimen was heat-treated at $930^{\circ}C$ for 6h on the Y211 substrate.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.267-268
• /
• 2007

기존의 Free Sintering 방법을 사용하는 LTCC(Low Temperature Cofiring Ceramics)는 수축률이 일정하지 않아서 설계 치수와 동일하게 제작하기 어려운 단점을 가지고 있다. 이에 따라서 정밀한 전자부품을 제작하기 위한 방안으로 X-Y면 방향에서의 변형을 거의 zero로 제어하는 Constrained Sintering(CS) 기술이 요구되고 있다. 본 연구에서는 LTCC 기판이 소성되는 동안에 변형을 억제하기 위하여 소성온도가 LTCC 기판 보다 높은 $Al_2O_3$ 분말과 유기물을 혼합하여 페이스트를 제작한 후에 스크린 프린팅 방법을 이용하여 도포 후에 Z축 방향으로 일축가압을 하면서 소성하여 수축률을 제어 하였다. 또한 바인더와 $Al_2O_3$ 분말의 함량에 대한 최적 조성의 $Al_2O_3$ 페이스트를 제작하여 0.5%로 수축률을 가지는 균일한 LTCC 기판을 구현 할 수 있었다.

• The Journal of the Korea Contents Association
• /
• v.8 no.3
• /
• pp.270-278
• /
• 2008

This study : An analysis of position accuracy of topography according to using LiDAR data, aerial photo and digital map for a study area was conducted. The study area was selected in Hadan area, Sahagu, Busan aerial LiDAR data and aerial photo in the scales of 1:20,000, which are high tech surveying ways were used. The final digital orthoimage according to orientation process for each image and image resampling was producted. Using it, a checkpoint was chosen, information about the checkpoints selected was extracted, a coordinate of Horizontal Position through the screen digitizing was also extracted. Both the coordinates of LiDAR data and aerial photo using digital map in the scales of 1:20,000 announced to the public from NGII(National Geographic Information Institute) were gradually compared and analyzed. Based on the digital map, as a result of being both compared and analyzed, it has shown to us that horizontal position of aerial photo is more accurate than that of aerial LiDAR surveying (RMSE-building x:24cm, y:26cm).

• Journal of Sensor Science and Technology
• /
• v.8 no.6
• /
• pp.454-460
• /
• 1999

$LaCoO_3$ thick-films for gas sensing layers were prepared on alumina substrate by screen printing method. The sensitivities to $C_4H_{10}$, $NH_3$, NO and CO gases were investigated for different heat treatment temperatures of the films. Their structural properties were examined by X-Ray Diffraction measurements and SEM photographs. The sensitivity of $LaCoO_3$ thick-film to CO gas was much higher than those of $C_4H_{10}$, $NH_3$, and NO gases. The optimal heat treatment and operating temperatures were $800^{\circ}C$ and $150^{\circ}C$, respectively. The sensitivities of $LaCoO_3$ thick-films to 500ppm and 1250ppm CO gas were 72% and 95%, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.322-322
• /
• 2013

최근 전자제품들의 소형화, 경량화, 다기능화가 활발히 진행됨에 따라, 고성능의 고출력용 인쇄회로기판(PCB)의 개발이 요구되고 있다. PCB는 전자제품의 각 부품을 전기적으로 연결하는 통로로서 전자제품의 소형화, 다기능화에 따라 고집적화가 요구되고 있다. 하지만 모든 전자장비의 고장의 85% 정도가 발열에 의한 것으로, PCB의 고집적화에 따른 발열문제가 매우 중요한 이슈가 되고 있다. 최근에는 이러한 문제점을 해결하기 위해 PCB의 방열층으로 양극 산화막을 금속 기판 위에 형성하고 이 절연층 위에 금속층을 회로로서 형성하는 방열 PCB 기판에 대한 연구가 활발히 진행되고 있다. 최근까지, 금속층 회로 형성을 위해 무전해 Ni 도금에 대한 연구가 활발히 이루어져 왔다. 하지만 주로 화학적, 전기화학적 관점에서 많은 연구자들에 의해 조사 연구되어 왔다. 본 실험에서는 anodized Al 절연층 위의 회로전극 부분으로 스크린 방법으로 Ag paste를 패턴 인쇄한 뒤, 무전해도금 방식으로 저렴한 Ni 전면 회로전극을 형성하여 전기전도도를 높이고, 저항을 낮출 수 있는 회로로서 기판의 손상을 최소화하고 선택적으로 Ag 패턴에만 Ni 전극회로를 형성시키는 것을 목표로 연구하였다. Ni-B 무전해 도금시 도금조의 온도는 $65^{\circ}C$, 무전해 도금액의 pH는 ~7 (중성)로 유지하였다. Al2O3 기판을 이용한 Ag Paste 패턴 위에 증착된 Ni-B 박막의 특성을 분석하기 위해 X-ray diffraction (XRD), AFM (Atomic Force Microscopy), SEM (Scanning Electron Microscope), XPS (X-ray Photoelectron Spectroscopy)을 이용하여 Ni-B 박막의 특성을 분석하였다.