• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.164-165
• /
• 2017

본 논문은 직렬 공진형 컨버터를 이용하여 낮은 저항을 갖는 주방 용기를 가열하기 위한 유도 가열(Induction Heating; IH)용 공진형 컨버터와 코일 설계방법을 제안한다. 기존 IH 시스템은 저항이 작은 용기를 가열할 때 낮은 전압이득으로 인해 정격보다 큰 전류가 흘러 스위칭 손실 및 전도 손실이 증가하고 소자의 정격 전류량을 초과하는 문제가 발생한다. 본 논문에서는 용기에 따른 임피던스를 분석하고 다양한 저항 조건의 용기를 모두 가열하기 위한 적절한 IH용 코일 설계 방법을 제안한다. 이는 2.4 kW의 최대 전력을 가지는 IH용 공진형 컨버터 시작품을 사용하여 제안하는 설계의 타당성을 검증하고자한다.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.1
• /
• pp.113-117
• /
• 2021

A composite active layer was designed based on graphene quantum dots, which is a low-dimensional structure, and a heterogeneous active layer of graphene quantum dots was applied to the interfacial defect structure to overcome the limitations. Increasing to 1.5~3.5 wt % PVP GQD, Vf changed from 2.16 ~ 2.72 V. When negative deflection is applied to the lower electrode, electrons travel through the HfOx/ITO interface. The Al + ions are reduced and the device dominates at low resistance. In addition, as the PVP GQD concentration increased, the depth of the interfacial defect decreased, and the repetition of appropriate electrical properties was confirmed through Al and HfOx/ITO. The low interfacial defects help electrophoresis of Al+ ions to the PVP GQD layer and the HfOx thin film. A local electric field increase occurred, resulting in the breakage of the conductive filament in the defect.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.3
• /
• pp.6-14
• /
• 2000

The high efficiency multi-resonant converter(MRC) is capable of operating at a high frequency because the losses are decreased due to the resonant tank circuit. Such a few MHz high frequency applications provide high power density[W/inch3] of the converter. However, the resonant voltage stress across the switch of the resonant tank circuit is 4∼5 times input voltage. This high voltage stress increases the conduction losses because of on-resistance of a MOSFET with higher rating. In this paper, the modeling analysis for the AT Forward MRC suggested to solve the these problems is discusses. The operational modes of the AT Forward MRC are divided to 8 equivalent modes according to the two switching sequences. Each mode analysis is covered using the equivalent circuits modeled over all of the paper. The operational principle of the resonant converter was verified through the experimental converter with 48[V] input voltage, 5[V]/50[W] output voltage/power and PSpice simulation. The measured maximum voltage, 5[V]/50[W] output voltage/power and PSpice simulation. The measure maximum voltage stress is 170[V] of 2.9 times the input voltage and the maximum efficiency is measured to 81.66%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.4
• /
• pp.298-308
• /
• 2017

This paper presents a Interleaved Buck Converter(IBC) system with Random PWM to reduce electromagnetic noise by harmonics. Swithced mode power supply generally controlled by high switching frequency have a electromagnetic interference(EMI) issue due to the high-voltage/high-current switching to regulate the voltage in buck converter. To solve the problem. we present a novel IBC system with PRBS. IBC system has two active switches with 180 phase difference that controll the cicuit with two PWM signal. IBC system may be disadventageous for the cost due to the addtion of one set of switch, but it has adventages of power distribution, current ripple cancellation, fast transient response, and passive component size reduction. To verify the validity of study, simulation program has been bulit using PSIM and the experimental results of IBC system using RPWM was compared with the conventinal PWM and randomized PWM.

• Analytical Science and Technology
• /
• v.15 no.6
• /
• pp.529-533
• /
• 2002

The separation and determination method of racemic isomers of flurbiprofen in urine samples have been investigated using column switching- HPLC, which include the sample treatment and concentration column. The optical rotation of two isomers separated were measured to identify d-form and l-form. The calibration curves are liear in the ranges of $0.11-5.4{\mu}g/mL$ for both d-form and l-form. The detection limits were $0.031{\mu}g/mL$ for l-isomes and $0.027{\mu}g/mL$ for d-isomer. The coefficients of variation of intra-day and inter-day precision of this method were about 1.8%. The present method was apllied to determine the concentration of racemic isomers in urine sample from human eating the drug.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.366-366
• /
• 2012

무기물 나노입자를 포함한 유기 박막인 나노 복합체를 사용하여 제작한 비휘발성 메모리 소자는 공정의 간단함과 낮은 전력구동이 가능하다는 장점 때문에 차세대 비휘발성 메모리 소자로 각광받고 있다. 다양한 나노입자를 포함한 유기 박막을 사용한 비휘발성 메모리 소자에 대한 연구는 많이 진행되었지만, 코어-쉘 나노입자가 poly (methylmethacrylate) (PMMA) 유기 박막에 분산되어 있는 나노 복합체를 활성층으로 사용하여 제작한 비휘발성 유기 메모리 소자의 전기적 특성과 메모리 메커니즘에 대한 연구는 비교적 미미하다. 본 연구에서는 코어-쉘 나노 입자가 PMMA 박막 안에 분산되어 있는 나노복합체를 사용한 비휘발성 메모리 소자를 제작하여 전기적 특성, 정보 유지력 및 메모리 스위칭 동작에 대하여 관찰 하였다. 소자 제작을 위해 hexane 안에 들어 있는 코어-쉘 나노입자를 Chlorobenzene에 용해되어 있는 PMMA에 넣어 초음파 교반기를 사용하여 나노입자를 고르게 분산하였다. 코어-쉘 나노입자가 PMMA에 고르게 분산 된 용액을 전극으로 사용 할 Indium-tin-oxide가 성장된 glass 위에 스핀코팅을 한 후 열처리를 하여 용매를 제거한 후 코어-쉘 입자가 PMMA에 분산되어 있는 박막을 형성하였다. 코어-쉘 입자가 PMMA에 분산된 나노복합체 위에 Al을 상부전극으로 열 증착하여 비휘발성 메모리 소자를 제작하였다. 제작된 소자의 전류-전압 (I-V) 특성을 측정결과는 특정한 두께에서 낮은 전도도 (ON state)와 높은 전도도 (OFF state)가 존재하는 쌍안정성 특성을 확인하였다. 코어-쉘 나노입자가 포함되지 않은 소자에서는 쌍안정성 특성이 보이지 않아 코어-쉘 나노입자가 비휘발성 메모리 소자의 기억 특성을 나타내는 중요한 저장 매체가 됨을 알 수 있었다. 제작된 메모리 소자의 메모리 동작에 대한 메커니즘 설명은 I-V와 에너지 밴드 구조를 사용하여 설명할 것이다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.6
• /
• pp.496-503
• /
• 2009

In this paper, a new three-phase interleaved isolated high efficiency boost dc-dc converter with active clamp is proposed. The converter is capable of increased power transfer due to its three-phase power configuration, and it reduces the rms current per phase, thus reducing conduction losses. Further, interleaved operation of three-phase boost converter reduces overall ripple current, which is imposed into fuel cells and realizes smaller sized filter components, increasing effective operating frequency and leading to higher power density. Each output current of three-phase boost converter is combined by the three-phase transformer and flows in the continuous conduction mode by the proposed three-phase PWM strategy. An efficiency of above 96% is mainly achieved by reducing conduction losses and switching losses are reduced by the action of active clamp branches, as well. The proposed converter and three-phase PWM strategy are analyzed, simulated and implemented in hardware. Experimental results are obtained on a 500 W prototype unit, with all of the design verified and analyzed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.10
• /
• pp.5105-5114
• /
• 2013

This paper is conducted a research of the cable and filter design considering the deep sea floor environment. The electric architecture which is being used in the subsea plant is comprised of the power supply unit of the high voltage, high-capacity drive system, long cable, and electric motor in the sea area. Conducted emission is occurred by the rapid voltage change at the moment of switching at high speed of inverter for driving motors. The more the length of the cable is lengthened, the worse the motor is influenced by transient voltage. Thus, the over voltage occurred in the drive motor was confirmed by designed wire which is considered R, L, line-to-line C, line-to-gnd C of long cable used in the subsea plant. A guide line of the subsea plant model is also suggested by using a filter to reduce conducted noise of PWM inverter drive-system.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.5
• /
• pp.7-13
• /
• 2002

In the resonant converters which can provide high efficiency and high power density, the resonant voltage stress is about 4-5 times the input voltage. It needs the power switch with high ratings. This is a reason why the conduction loss is increased. In this paper, it proposes the alternately zero voltage switched forward, flyback multi resonant converter topology for reducing the voltage stress using alternately zero voltage switching technique. And the proposed AT forward MRC is experimentally considered about the loop gain with HP4194A network analyzer.

• Journal of IKEEE
• /
• v.14 no.3
• /
• pp.250-255
• /
• 2010

The interleaved power management IC(PMIC) with DTMOS(Dynamic Threshold voltage MOSFET) switching device is proposed in this paper. The buck-boost converter used to provide the high output voltage and low output voltage for portable applications. Also we used the PWM(Pulse Width Modulation) control method for high power efficiency at high current level. DTMOS with low on-resistance is designed to decrease conduction loss. The interleaved PMIC to reduce output ripple. And step-down DC-DC converter in stand-by mode below 1mA is designed with LDO in order to achive high efficiency.