• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.7
• /
• pp.858-862
• /
• 2018

The purpose of this study is to improve the current vessel departure control regulations to prevent traffic congestion after the lifting of vessel departure controls due to restricted visibility. AIS data was collected to analyze the traffic volume of normal traffic flow and after departure control. A statistical test was conducted to confirm the difference in traffic volume at peak hours according to whether or not departure control was used. The results of the t-test showed that there was a significant difference in traffic volume among groups of less than 10,000 tons in gross tonnage. However, the Mann-Whitney test showed no difference in traffic volume regardless of vessel control. Small and medium-sized vessels of less than 10,000 tons after departure control increased in traffic volume by 142% over normal traffic, and it was concluded that traffic congestion resulted as these small and medium-sized vessels were departing at the same time as large vessels of more than 10,000 tons. In order to prevent vessel collision accidents due to traffic congestion, it is suggested that the navigability of vessels less than 160 m or less than 10,000 tons should be improved.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.1
• /
• pp.119-131
• /
• 2021

This study quantitatively derived the direct socio-economic effects of the Gyeongbu Expressway, which opened in 1970, and suggested a methodological approach for more reliable results. The scenario was set when the Gyeongbu Expressway was not constructed in 1970, the opening of the Gyeongbu Expressway was delayed by 10 years, and the toll road between Seoul and Daejeon, or between Seoul and Gangneung was opened instead of the Gyeongbu Expressway as suggested by the World Bank. In addition, direct benefits were estimated by calculating and comparing the current vehicle operating costs, travel time costs, traffic accident costs, and environmental pollution costs. As a result, it was estimated that about 351 trillion won in direct benefits occurred, and it can be seen that the promotion of the construction project of the Gyeongbu Expressway at that time had a huge impact on South Korea's social economy.

• Environmental and Resource Economics Review
• /
• v.30 no.4
• /
• pp.627-648
• /
• 2021

The fine-dust season management system refers to the policy of implementing enhanced reduction measures in transportation, power, business and living sectors in winter, when fine dust levels are high. The fine dust season management system is a regulatory policy that causes social costs and transfers to various economic players. Equity is an important issue for the cost burden. Therefore, in this study, the cost of each power generator was analyzed using the coal power generation reduction amount of each power generator to verify that the cost of the power sector is evenly distributed. In particular, the effect of the fine dust season management system on coal power generation of power generators was analyzed by applying a synthetic control method that can identify the time-variable effect of the policy. It was confirmed that the fine dust season management system reduced volume of fuel and power generation in coal power plants, resulting in an increase in the cost of the power generation sector, even considering the effect of some power demand due to the COVID-19 crisis. However, it could be seen that these costs were not distributed equally among the generators, and that they were more costly to the specific generators.Social costs incurred by fine dust season management need to be improved so that stakeholders are equally burdened.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.91-96
• /
• 2021

The enhancement of thermoelectric figure of merit was achieved by the simple processes of sieving and high energy ball milling, respectively, which are enable to reduce the grain size of n-type Bi₂Te₃ thermoelectric materials. By optimizing the grain size, the electrical conductivities and thermal conductivities were controlled. In this study, spark plasma sintering was employed for hindering the grain growth during the sintering process. The thermoelectric figure of merit was measured to be 0.78 in the samples with 30 min high energy ball milling process. Notably, this value was 40 % higher than that of pristine Bi₂Te₃ sample. This result shows the properties of thermoelectric materials can be readily controlled by optimization of grain size via simple ball milling process.

• Membrane Journal
• /
• v.32 no.5
• /
• pp.292-303
• /
• 2022

An eco-friendly energy conversion device without the emission of pollutants has gained much attention due to the rapid use of fossil fuels inducing carbon dioxide emissions ever since the first industrial revolution in the 18th century. Polymer electrolyte membrane fuel cells (PEMFCs) that can produce water during the reaction without the emission of carbon dioxide are promising devices for automotive and residential applications. As a key component of PEMFCs, polymer electrolyte membranes (PEMs) need to have high proton conductivity and physicochemical stability during the operation. Currently, perfluorinated sulfonic acid-based PEMs (PFSA-PEMs) have been commercialized and utilized in PEMFC systems. Although the PFSA-PEMs are found to meet these criteria, there is an ongoing need to improve these further, to be useful in practical PEMFC operation. In addition, the well-known drawbacks of PFSA-PEMs including low glass transition temperature and high gas crossover need to be improved. Therefore, this review focused on recent trends in the development of high-performance PFSA-PEMs in three different ways. First, control of the side chain of PFSA copolymers can effectively improve the proton conductivity and thermal stability by increasing the ion exchange capacity and polymer crystallinity. Second, the development of composite-type PFSA-PEMs is an effective way to improve proton conductivity and physical stability by incorporating organic/inorganic additives. Finally, the incorporation of porous substrates is also a promising way to develop a thin pore-filling membrane showing low membrane resistance and outstanding durability.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3B
• /
• pp.311-319
• /
• 2006

A bed level change model(SED-FLUX) is introduced based on the realistic sediment transport process including bed load and suspended load behaviours at the bottom boundary layer. The model SED-FLUX includes wave module, hydrodynamic module and sediment transport and diffusion module that calculate suspended sediment concentration, net sediment erosion flux($Q_s$) and bed load flux. Bed load transport rate is evaluated by the van Rijn's TRANSPOR program which has been verified in wave-current fields. The net sediment erosion flux($Q_s$) at the bottom is evaluated as a source/sink term in the numerical sediment diffusion model where the suspended sediment concentration becomes a verification parameter of the $Q_s$. Bed level change module calculates a bed level change amount(${\Delta}h_{i,j}$) and updates a bed level. For the model verification the limit depth of the bed load transport is compared with the field experiment data and some formula on the threshold depth for the bed load movement by waves and currents. This model is applied to the beach profile changes by waves, then the model shows a clear erosion and accumulation profile according to the incident wave characteristics. Finally the beach evolution by waves and wave-induced currents behind the offshore breakwater is calculated, where the model shows a tombolo formation in the landward area of the breakwater.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.5
• /
• pp.108-126
• /
• 2023

In this paper, the dynamic hard shoulder running for bus only (HSRFBO) was presented to solve the traffic congestion by increase the capacity in chronic congested sections of highways, and a simulation was performed to evaluate the comparison with the current hard shoulder running for all vehicles(HSRFAV) and median bus only lane and HSR(MBOLHSR). According to the evaluation results, it was evaluated to be more advantageous in terms of traffic flow and safety than the current HSRFAV. In addition, the speed of passing buses is slightly reduced compared to the MBOHSR, but the speed of entering and exiting buses is increased and the speed of buses and cars is greatly improved. Therefore It was analyzed that the efficiency of transport personnel was also improved. In particular, it is expected that traffic flow will be stabilized as the difference in speed between passenger cars and buses will be greatly reduced, and violations of exclusive bus lanes by passenger cars will be greatly reduced. In addition, the operation time of HSR is greatly reduced, so that the original function of the shoulder lane can be maintained as much as possible. As a result, it was analyzed that the risk of accidents was significantly reduced when operating HSRFBO compared to when operating MBOHSR, and cross-conflicts with high accident severity did not occur.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.1
• /
• pp.39-48
• /
• 2009

Biodiesel is estimated to be the best recycling energy source as an alternative fuel for transportation vehicles which represents the biggest share of greenhouse effect gas exhausts. Thus, in order to widely expand use of biodiesel and to enhancement its reliability, studies on quality improvement of biodiesel is needed. In this study, we have produced biodiesel(BD100, BD20) through esterification reaction using raw material of waste frying oil and analyzed compatibility with 24 items of quality criteria. As waste frying oil has high contents of unsaturated fatty acid such as Oleic acid, Linoleic acid and Linolenic acid, it is confirmed that there is no problem in using the same as a raw material of biodiesel. The result of analyzing the quality criteria items of biodiesel showed that it satisfied all the quality criteria except the oxidation stability of BD100, which was 2 hours, fatty acid methyl ester of BD20, which was 18.6w% and the filter plugging point, which was $-5^{\circ}C$. We believe that it will contribute to improved utilization of waste resources as alternative energy if studies on technology to improve quality of some items are provided.

• Journal of KIISE:Computer Systems and Theory
• /
• v.34 no.8
• /
• pp.337-347
• /
• 2007

An embedded system is called a multi-mode embedded system if it performs multiple applications by dynamically reconfiguring the system functionality. Further, the embedded system is called a multi-mode multi-task embedded system if it additionally supports multiple tasks to be executed in a mode. In this Paper, we address a HW/SW partitioning problem, that is, HW/SW partitioning of multi-mode multi-task embedded applications with timing constraints of tasks. The objective of the optimization problem is to find a minimal total system cost of allocation/mapping of processing resources to functional modules in tasks together with a schedule that satisfies the timing constraints. The key success of solving the problem is closely related to the degree of the amount of utilization of the potential parallelism among the executions of modules. However, due to an inherently excessively large search space of the parallelism, and to make the task of schedulabilty analysis easy, the prior HW/SW partitioning methods have not been able to fully exploit the potential parallel execution of modules. To overcome the limitation, we propose a set of comprehensive HW/SW partitioning techniques which solve the three subproblems of the partitioning problem simultaneously: (1) allocation of processing resources, (2) mapping the processing resources to the modules in tasks, and (3) determining an execution schedule of modules. Specifically, based on a precise measurement on the parallel execution and schedulability of modules, we develop a stepwise refinement partitioning technique for single-mode multi-task applications. The proposed techniques is then extended to solve the HW/SW partitioning problem of multi-mode multi-task applications. From experiments with a set of real-life applications, it is shown that the proposed techniques are able to reduce the implementation cost by 19.0% and 17.0% for single- and multi-mode multi-task applications over that by the conventional method, respectively.

• Journal of Food Hygiene and Safety
• /
• v.22 no.3
• /
• pp.213-217
• /
• 2007

LPS induces the synthesis of several inflammatory cytokine, chemokine, NO and inflammation in the liver of rats. The purpose of this study was to investigate the preventive effects of Rubus coreanum Miquel (RCM) In lipid metabolism. RCM of 100 mg/kg concentration was intraperitoneally administered into rats at dose of 1.5ml/kg for 20 days. On the day 21, 1.5ml/kg of LPS was injected 4 hours before anesthetization. We examined the lipid-related functions by measuring the levels of triglyceride (TG), total cholesterol (TC), total lipid (TL), high-density lipoprotein cholesterol (HDL-C) in serum and malondialdehyde(MDA) in liver tissue. The results showed that LPS treatment increased the values of TG, TC, TL and MDA, decreasing that of HDL-C. But RCM pretreatment decreased the high values of TG, TC, TL and MDA to the low values and increased the low value of HDL-C to the high value. These results suggested that RCM could be used as the potential candidate for the lipid metabolism natural supplement.