• Journal of the Korean Solar Energy Society
• /
• v.34 no.3
• /
• pp.98-106
• /
• 2014

The effect of blockage ratio on wind tunnel testing of small vertical-axis wind turbine has been investigated in this study. Height and rotor diameter of the three blades Darrieus vertical axis wind turbine used in present test were 0.4m and 0.35m respectively. We measured the wind speeds and power coefficient at three different wind tunnels where blockage ratio were 3.5%, 13.4% and 24.7% respectively. The test results show that the measured powers have been strongly influenced by blockage ratio, generally increased as the blockage ratio increases. The maximum power at higher blockage ratio has been obtained at relatively high tip speed ratio compared with that at low blockage ratio. The measured power coefficients under high blockage ratio can be improved from proper correction using the simple correction equation based on blockage factor. In present study, the correction error for power coefficient can be less than 5%, however correction effectiveness reveals relatively poor at high blockage ratio and low wind speed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.6
• /
• pp.623-628
• /
• 2010

This paper presents a wind-power-driven portable power source based on piezoelectric effect. Positive piezoelectric effect is one of efficient and widely used mechanisms for converting mechanical energy to electrical energy. However, for this mechanism, a periodic mechanical stress with a high frequency, as in the case of AC, has to be exerted; such stress cannot be exerted by the natural wind in the environment. The natural wind has a constant velocity with slow and irregular variations, as in the case of DC. In this paper, we propose a novel and simple mechanism to convert mechanical energy into electrical energy. The DC-like wind flow is passed through a propeller to convert it to an AC-like wind flow; the resultant AC-like periodic flow induces vibrations in a piezoelectric cantilever, thereby, generating electrical power. This system is expected to be one of practical solutions for wireless energy supply to ubiquitous sensor networks (USNs).

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.5
• /
• pp.513-516
• /
• 2011

The dynamic behavior of a small wind-turbine blade was analyzed experimentally. Arrays of fiber Bragg-Grating (FBG) sensors attached along the blade were used to measure the strains of the blade surface. An impact test was performed to estimate the resonance frequencies of the fundamental and higher modes of the cantilever blade system developed for this study. The results were similar to the results for conventional strain gages. However, FBG sensors could sense modes that strain gauges could not sense. The strains obtained from the FBG sensor array were used to estimate displacement-mode shapes of the blade.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.5
• /
• pp.465-475
• /
• 2012

This study was carried out with two goals. One was the development of a model of a wind turbine blade airfoil and the other was the application of this folding blade. In general, in large-sized (MW) wind turbines, damage is prevented because of the use of a pitch control system. On the other hand, pitch control is not performed in small wind turbines since equipment costs and maintenance costs are high, and therefore, the blade will cause serious damage. The wind turbine proposed in this study does not require maintenance, and the blades do not break during high winds because they are folded in accordance with changes in the wind speed. But generators are not cut-out, while maintaining a constant angle will continue to produce. The focus of this study, the wind turbine is continued by folding blade system in strong winds and gusts without stopping production.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.12
• /
• pp.1273-1283
• /
• 2011

A 3-dimensional unsteady numerical analysis has been performed to evaluate the aerodynamic characteristics of a Giromill. Generally, the structure of a Giromill is simple and therefore easy to develop. In addition, the high solidity of the Gironmill helps improve the self-starting capacity at a low tip speed ratio (TSR). However, contrary to the Darrieus wind turbine which has a TSR of 4-7, a Giromill has a low TSR of 1-3. In this study, the aerodynamic characteristics of the Giromill are investigated using computational fluid dynamics (CFD). Three straight-bladed wings are used, and the solidity of the Giromill is 0.75. In contrast to a Darrieus wind turbine having low solidity, the Giromill shows a sudden decrease in the aerodynamic performance because of the interference between the wings and an increase in the drag on the wings in the downstream direction where wind flow is significantly reduced. Consequently, the aerodynamic performance decreased at a TSR value lower than 2.4.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.2
• /
• pp.739-748
• /
• 2013

In this study, analytical works for the induced winds due to traveling vehicles on highway have been conducted by Computation Fluid Dynamics (CFD). The traveling condition was considered in two cases: (a) single direction and (b) bi-direction. The analysis was focused on the effects of the induced winds on the upper part of a median strip while the aerodynamic characteristics of the vehicles were directly analyzed in the previous studies. From the analysis results, it has been found that the maximum magnitude of the induced winds was 2.2 m/s when the vehicles travel with the speed of 50 km/h. Additionally, 4.0 m/s and 5.3 m/s were obtained with the speed of 90 km/h and 120 km/h, respectively. Especially, the induced winds was generated about 84% of the vehicle speed at 1.0 m above from the median strip when the vehicles travel with the speed of 120 km/h. The induced winds was maintained during the very short period while the traveling. conclusively, it is noted that the wind power generation can be possible by using the small-sized wind power generators installed on median strips throughout the analytical results in this study.

• Bulletin of Korea Environmental Preservation Association
• /
• s.389
• /
• pp.8-24
• /
• 2010

도시생활과 관련된 교통 주택부문의 온실가스 배출량은 43%를 차지하고 있어 도시에서의 온실가스 저감대책 마련이 시급하며, 저탄소 녹색성장의 시대적 요구에 따라 기후변화 위기에 적극적으로 대응할 수 있는 저탄소 녹색도시 조성이 필요한 실정이다. '저탄소 녹색도시'는 지구온난화 등 기후변화의 주요 원인인 이산화탄소의 배출을 획기적으로 감축하고, 지속가능한 도시기능을 확충하면서 자연과 공생하는 도시를 말한다. 최근의 '저탄소 녹색도시'는 기존의 녹색도시와 또 다른 양상을 보이고 있다. 자원순환과 신재생에너지원의 도입을 주장하고, 탄소상쇄를 위한 에너지 및 자원절감 전략을 중요시 하고 있다. 선진국에서는 이미 주거단지내 소비되는 난방과 전력은 단지내에서 생산되는 신재생에너지를 활용하고 있으며, 모든 주택의 지붕위에 태양광 패널을 설치하고 단지 내 열병합 자가발전소에서 산업폐기물을 소각하여 에너지를 생산함으로써 제로 에너지(Zero Energy)를 실현하고 있다. 선진국 뿐 아니라 전 세계의 이목이 '저탄소 녹색도시'에 집중되고 있으며 저탄소 녹색도시를 조성해야 하는 것은 선택이 아닌 의무가 되고 있다. 우리나라도 2020년 그린홈 100만호 보급을 목표로 주택분야 보급가능 신재생 에너지원을 태양열, 지열, 소형풍력, 연료전지 등으로 다양화하여 안정적 보급 기반을 확보해 가고 있다. 녹색도시를 조성하기 위해서는 저탄소 주택, 저탄소 에너지, 녹색교통, 생태녹지, 물 및 자원순환등 핵심요소들의 적용방안이 검토되어져야 한다. 이에 본지에서는 "저탄소 녹색도시의 해외사례와 국내 적용방향", "그린홈 100만호 보급사업 그간 성과와 발전방향", "온라인 전지자동차의 기술 개발 동향" 내용에 대하여 살펴보고자 한다.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.4
• /
• pp.23-32
• /
• 2013

In order to evaluate the bearing capacity behaviour of a monopod suction bucket foundation for an offshore wind tower at the western sea of Korea, a centrifuge load test and numerical analyses were performed. The monopod bucket foundation was designed to be installed in a silty sand layer. The model soil was prepared to simulate a target site by using soil samples having similar properties and controlling relative density. In-flight miniature cone penetration test and bender element array were used to confirm that the model soil had represented the target site conditions. The load - rotation curve of the centrifuge load test was analysed. A series of numerical analyses were performed to validate the experimental conditions. Self-weight of the model, distance to the boundary and elastic modulus of the soil layer were varied to study their effects on the load - rotation curves.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.942-945
• /
• 2010

The development of decentralized power has appeared as part of an effort to decrease the energy loss and the cost for electric power facilities through installing small renewable energy generation systems including solar and wind power generation. Recently a new era for decentralized power environment in building is coming in order to handle the climatic and environmental change occurred all over the world. Especially solar and wind power generation systems can be easily set up and are also economically feasible, and thus many industrial companies enter into this business. This paper suggests the overall architecture for the decentralized renewable power system and the prediction method of power on climatic change. The ultimate goal is to help manage the overall power efficiently and thus provide the technological basis for achieving zero-energy house.

• Journal of Internet of Things and Convergence
• /
• v.10 no.1
• /
• pp.1-6
• /
• 2024

In order to increase the use of electric vehicles (EVs) and minimize grid strain, microgrid using renewable energy must take an important role. Microgrid may use fossil fuels such as small diesel power, but in many cases, they can be supplied with energy from renewable energy, which is an eco-friendly energy source. However, renewable energy such as solar and wind power have variable output characteristics. Therefore, in order to meet the charging and discharging energy demands of electric vehicles and at the same time supply load power stably, it is necessary to review the configuration of electric vehicle charging infrastructure that utilizes diesel power or electric vehicle-to-grid (V2G) as a parallel energy source in the microgrid. Against this background, this study modelized a microgrid that can stably supply power to loads using solar power, wind power, diesel power, and V2G. The proposed microgrid uses solar power and wind power generation as the primary supply energy source to respond to power demand, and determines the operation type of the load's electric vehicles and the rotation speed of the load synchronous machine to provide stable power from diesel power for insufficient generations. In order to verify the system performance of the proposed model, we studied the stable operation plan of the microgrid by simulating it with MATLAB /Simulink.