• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.509-510
• /
• 2016

본 논문은 계통연계형 인버터의 위상추종기법인 SRF-PLL을 모델링하고, FPGA에 구현하기 위해 System Generator를 이용하여 설계하였다. SRF-PLL의 비례-적분 이득은 소신호 해석을 하여 일반화를 통해 입력전압의 크기에 관계없이 적용가능하며, 주파수 응답에서 65도 위상여유를 갖는 안정한 이득을 산정하였다. FPGA 구현을 위해 MATLAB/SIMULINK와 연동 가능한 System Generator를 이용하여 SRF-PLL을 모델링하였으며, MATLAB 기반의 시뮬레이션과 실험을 통하여 위상추종 특성을 분석하였다.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.530-531
• /
• 2012

본 논문에서는 태양광 발전시스템에서 사용되는 벅 컨버터의 새로운 모델을 제시하고, 선형화하여 모델링하였다. 이 모델을 통하여 전류와 전압 제어기를 설계하고, 그 특성을 MATLAB과 PSIM으로 모의실험하여 검증하였다.

• Proceedings of the KIPE Conference
• /
• 2018.11a
• /
• pp.223-224
• /
• 2018

본 논문에서는 전기자동차용 저전압 배터리 충전기(Low-voltage DC-DC Converter, LDC)에 적합한 입력 직렬-출력 병렬 구조의 능동 클램프 포워드 컨버터의 모델링 및 제어기 설계를 제안한다. 제안하는 컨버터는 모든 스위치에서 소프트 스위칭을 성취하기 때문에 높은 효율을 달성할 수 있다. 또한 누설 인덕턴스의 영향을 포함한 컨버터의 정확한 소신호 모델을 통하여 모델링 기반의 제어기 설계를 제시한다. 제어기의 시뮬레이션 및 3.2kW급 시작품의 실험을 통하여 제안하는 컨버터의 성능을 검증하였다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.4C
• /
• pp.371-379
• /
• 2002

In this paper, the MMIC SPST switches operating from DC to 3GHz were designed and implemented. Prior to the design of switches, the small and large-signal switch models were needed to predict switch performance accurately. The newly proposed small-signal switch model parameters were extracted from measured S-parameters using optimization technique with estimated initial values and boundary limits. In the extraction of large-signal switch model parameters, the current source was modeled by fitting empirical equations to measured DC data and the charge model was derived from extracted channel capacitances from measured S-parameters varying the drain-source voltage. To design basic series-shunt SPST switches and isolation-improved SPST switches, we applied this model to commercial microwave circuit simulator. The improved SPST switches exhibited 0.302dB insertion loss, 35.762dB isolation, 1.249 input VSWR, 1.254 output VSWR, and about 15.7dBm PldB with 0/-3V control voltages at 3GHz.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.1
• /
• pp.1-11
• /
• 2000

An accurate technique to retrieve HEMT modeling parameters with measurements of S-parameters and DC characteristics of HEMT is proposed. The extrinsic series resistances among HEMT modeling parameters are determined by the FUKUI method using the measured DC characteristics. And other parameters are determined by the measured S-parameters by HP 8510C Network Analyzer with various values of DC bias. The transconductance retrieved from the measured S-parameters, however, shows only 0.078% error comparing with the measured gm values. Therefore, the S-parameters measured directly for an individual transistor should be used for an accurate determination of the model parameters. The procedure for the retrieval of the circuit modeling parameters redescribed in detail in this thesis.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.11
• /
• pp.1633-1640
• /
• 2013

In this paper, noise parameters for high frequency modeling of dual-gate FET are extracted and analyzed. To extract thermal noise parameter of dual gate, noise characteristics are measured by changing input impedance of noise source using Tuner, and the influence of pad parasitic elements are subtracted using open and short dummy structure. Measured results indicated that the dual-gate FET is improved the noise figure by 0.2dB compared with conventional cascode structure FET at 5GHz, and it confirmed that the noise figure has dropped due to reduction of capacitances between the drain and source, gate and drain by simulation and analysis of small-signal parameters.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.7
• /
• pp.1039-1048
• /
• 2013

Generally, the buck converter controller was designed to control output voltage of the converter. However, design of the controller in photovoltaic power conditioning system is different from general design. the controller in photovoltaic power conditioning system controls input voltage of the converter(output voltage of the solar cell) for MPPT(Maximum Power Point Tracking). This paper proposes novel buck converter model which can control input voltage of the converter. We integrate this model with a model of solar cell. and linearize at the operating point(MPP). In addition, we determine whether or not suitable for the general linear controller design into small and large signal analysis.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.131-136
• /
• 2008

Two Ka-band 3-stage power amplifiers were designed and fabricated using $0.18-{\mu}m$ CMOS technology. For low loss matching networks for the amplifiers, two substrate-shielded transmission line structures, having good modeling accuracy up to 40 GHz were used. The measured insertion loss of substrate-shielded microstrip-line (MSL) was 0.5 dB/mm at 27 GHz. A 3-stage CMOS amplifier using substrate-shielded MSL achieved a 14.7-dB small-signal gain and a 14.5-dBm output power at 27 GHz in a compact chip area of 0.83$mm^2$. The measured insertion loss of substrate-shielded coplanar waveguide (CPW) was 1.0 dB/mm at 27 GHz. A 3-stage amplifier using substrate-shielded CPW achieved a 12-dB small-signal gai and a 12.5-dBm output power at 26.5 GHz. This results shows a potential of CMOS technology for low cost short-range wireless communication components and system.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.7
• /
• pp.156-161
• /
• 1996

Accurate equivalent circuit modeling using multi-circuit optimization has been perfomred for detemining small-signal model of AlGaAs/GaAs HBTs. Three equivalent circuits for a cutoff biasing and two active biasing at different curretns are optimized simultaneously to fit gheir S parameters under the physics-based constrain that current-dependent elements for one of active circuits are connected to those for another circit multiplied by the ratio of two currents. The cutoff mode circuit and the physical constrain give the advantage of extracting physically acceptable parameters, because the number of unknown variables. After this optimization, three ses of optimized model S-parameters agree well with their measured S-parameters from 0.045 GHz to 26.5GHz.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.4
• /
• pp.307-316
• /
• 2001

In this paper, the multiple output forward converter forPC power supply with weighted voltage mode control which improves the characteristics of DC and transient responses is analyzed and designed. The power stage model of this converter including all the major parasitic components is derived and the small signal model is also derived. Determination of the weighting factors and a design procedure for the loop compensation are presented. Finally, the proposed controller is verified through the simulation of three output forward converter with SABER, and the experiment.