• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.2
• /
• pp.135-141
• /
• 1995

Abstract The sintering behavior and the electrical properties of sintered PZT ceramics using 2.45 GHz microwave energy were investigated. The ceramics were sintered between $1050 ~ 1130^{\circ}C$ for 5 min. Sintered body with high density and good electrical properties were achieved as the sintering temperature increases. Above $1090^{\circ}C$, however, the bulk density was decreased due to the volatilization of PbO component, and also electrical properties were decreased. The relative dielectric constant, mechanical Quality factor, electro- mechanical coupling factor of microwave sintered body at $1090^{\circ}C$ without PbO atmosphere were 1900, 80, 0.53 respectively, which were comparable to conventional sintering values. The sintering process completed within 20 min using microwave hybrid energy. The processing time and the amount of energy con-sumption could be reduced by microwave hybrid energy assisted rapid sintering.

• Journal of the Korean Magnetics Society
• /
• v.4 no.2
• /
• pp.94-99
• /
• 1994

This work addresses the relationship between initial complex permeability and porosity in polycrystalline Mg-ferrite material. The initial permeability corresponds to Snoek theory except the sample with large grains. The frequency which initial real permeability, $\mu$' equal 1 due to domain rotation are found in the frequency range 50-80 [MHz]. Internal magnetic field which is considered as mainly anisotropy field is 100[Oe] which is obtained from the relationship between initial complex permeability and porosity in polycrystalline Mg-ferrite material. This is almost the half value of reported anisotropy field of single Mg-ferrite. The difference between them is almost due to domain wall effect in polycrystalIine Mg-ferrite material.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.7
• /
• pp.19-26
• /
• 2008

• Resources Recycling
• /
• v.16 no.4
• /
• pp.10-16
• /
• 2007

As a basic study for reusing converter slag as slow-release potassium fertilizer by a sintering process, powdery converter slag and reagent grade $SiO_2\;and\;K_2CO_3$ were mixed with ball mill above 24 hours and sintered at $900^{\circ}C{\sim}1000^{\circ}C\;for\;10{\sim}60$ min. Basicity of the mixed powder was controlled to 0.7, 1.0 and 1.4 and content of $K_2O$ was fixed with 22 mass%. After sintering, property of the potassium fertilizer was investigated with X-ray diffraction pattern and ICP analysis. Also effects of basicity, sintering temperature and time on the making slow-release potassium fertilizer was investigated. Water solubility of KBO in sample were decreased with sintering time, temperature and decreased with basicity. Citric acid solubility of $K_2O$ were increased with basicity and decreased with sintering temperature.

• Proceedings of the KSEEG Conference
• /
• 1999.04a
• /
• pp.291-293
• /
• 1999

• Resources Recycling
• /
• v.19 no.1
• /
• pp.33-39
• /
• 2010

The spheric sintered body with $6{\pm}2mm$ diameter was manufactured in a rotary kiln at $1125^{\circ}C$/15 min using green body formed by pelletizing the batch powder composing of coal bottom ash produced from power plant and dredged soil by 70:30, wt%. And the physical properties of sintered body (BD) were analyzed to confirm the possibility for applying to an absorbent to restore a contaminated soil. The sintered body had a giant pore above 100 ${\mu}m$ and a fine pore below 10 ${\mu}m$, and bulk density was 1.4. Also its specific surface area, porosity and void proportion were $12.0m^2/g$, 30.1% and 38.2% respectively. The crushed body (BD-C), produced by crushing a BD specimen into an irregular shape with a aspect ratio of about 2, was similar to BD specimen at bulk density and pore size distribution. But it had superior values of specific surface area, porosity and void proportion compared with BD specimen owing to a decreased apparent volume due to conversion of closed pore existed at interior of BD to open pore during a crushing process. The IEP of sintered body occurred at about pH=5, so the optimum pH condition of reacting aqueous solution could be known before bonding a microbe to the sintered body. Hence, the optimum void proportion and porosity of an absorbent can be obtained by appropriate mixing a BD with BD-C from the base data calculated in this study.

• Resources Recycling
• /
• v.12 no.6
• /
• pp.8-12
• /
• 2003

According to the recent trend to raise the horizontal scan frequency to increase the image refinement of the High Definition TV and High Resolution Display, material with low core loss is required for the ferrite core for deflection yoke, which is secured even in the high frequency range. liking notice of the influence on the fine structure of Mg-Zn ferrite by the chemical com position and process, low temperature sintering was proceeded. Cu was added to the low loss Mg-Zn system ferrite. After select-ing MgO, ZnO, $Fe_2$$O_3$, CuO, MgO was substituted for CuO while varying the composition ratio. Then the sample was sintered for 3 hours between $980～1350^{\circ}C$ Magnetic permeability, power consumption, shrinkage rate, core loss were measured. The start-ing temperature to test the shrinkage of the sample was nearby $900^{\circ}C$, it increased according to the substitution process of Cu, and the firing temperature was lowered about $-50～-75^{\circ}C$ alongside of the process.

• Journal of the Korean Magnetics Society
• /
• v.7 no.2
• /
• pp.69-75
• /
• 1997

The effect of oxide additive system and $Po_2$ condition on the power loss, microstructure, initial permeability, ${\mu}_i$ vs. temperature curve of Mn-Zn ferrites has been investigated. The density and permeability increased with various additive systems while the power loss decreased. It was confirmed that the oxide additives are grain boundary materials and do not change the magnetic properties of Mn-Zn ferrites such as $T_{spm}$ and $T_c$. The ${\mu}_i$ vs. T curve indicated that $T_{spm}$ moved to the higher temperature as $Po_2$ increased. It was also confirmed that the microstructure of Mn-Zn ferrites was independent of the $Po_2$ control during cooling.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.328-329
• /
• 2005

ZnO 바리스터의 소결조건에 따른 바리스터 특성과 유전특성을 조사하였다. 소결조건에서 소결시간 및 시간에 따라 바리스터 전압의 변화를 볼 수 있었으며 적정소결온도에서 바리스터 전압 $V_{1mA}$ 및 $V_{10mA}/V_{1mA}$특성은 225 ~ 250. 0.85 ~ 0.9의 특성을 얻을 수 있었다. 특히, 유전특성의 경우 주파수에 따라 정전용량의 변화가 높은 온도에서 소결한 경우 높게 나타났으며 적정 소결온도에서는 유전율은 720 ~ 740, 유전손실은 2.5% 이하의 값을 얻을 수 있었다.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.05a
• /
• pp.29-33
• /
• 2003

최근 이동 정보통신 분야의 발전에 따라 단말기 및 관련 부품들을 소형 경량화 하는 것이 매우 중요한 기술요소로 부각되고 있다. 이를 위해서는 기판의 배선밀도를 높이는 것과 개별 부품 또는 모듈의 크기와 무게를 줄이는 것이 절실히 필요하며, 이러한 요구에 부응하기 위해 기존의 다층 PCB 기술이나 MCM 기술에 비해 우수한 배선밀도와 양호한 전기적 특성을 갖는 저온 동시소성 세라믹(Low Temperature Co-fired Ceramic) 기술이 개발, 적용되고 있다. 본 논문에서는 이러한 LTCC 기판의 소결에 있어 기존의 소결 공정인 전기로 소결 공정과 microwave를 이용한 소결 공정을 이용하여 소결 하였을 때, LTCC 기판의 수축율과 무게감소, 그에 따른 밀도변화, SEM 을 이용한 표면형상 분석을 통해 급속가열을 통한 공정시간의 단축, 낮은 에너지 소비로 인한 제조단가의 절감, 균일한 가열로 인한 소결온도의 저하 등의 장점을 갖는 microwave sintering 을 적용할 수 있는 가능성을 제시하였다.