• Korean Chemical Engineering Research
• /
• v.50 no.6
• /
• pp.1021-1026
• /
• 2012

The transient mass transfer in a single droplet system consisting of 1-octanol (continuous phase)/aqueous succinic acid solution (dispersed phase) was investigated in the presence of chemical reaction, which is acid/anion exchange reaction of succinic acid and tri-n-octylamine (TOA). This succinic acid extraction by TOA can be considered to occur at the interface between organic and aqueous phase, that is, heterogeneous reaction system. The basic properties of the system such as viscosity, density, distribution coefficient, terminal velocity of droplet, and diffusion coefficient were measured experimentally or calculated theoretically, and used for theoretical calculation of characteristic parameters of mass transfer later. The effects of succinic acid concentration on the terminal velocity was negligible in the existence of TOA, although the terminal velocity increases with succinic acid concentration in the absence of TOA. On the contrary, the terminal velocity decreases with TOA concentration. While droplets falls through organic phase, the trajectory of droplets is observed to oscillate around its vertical path. A mass trnasfer cell was prepared to monitor the mass transfer behavior in a single droplet and used to measure the mean concentration of succinic acid inside droplet. The results are expressed with dimensionless parameters. Under 50 g/L succinic acid condition, the system with 0.1 mol/kg TOA showed that the molar flux decreases in proportion to the decrease of concentration gradient, while in the case of 0.5 mol/kg TOA Sh increases rapidly with time indicating the molar flux of succinic acid decreases relatively slowly compared to the decrease in concentration gradient.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.12
• /
• pp.209-218
• /
• 2012

Recently, the Field Programmable Stateful Logic Array (FPSLA) was proposed as one of the most promising system integration technologies which will extend the life of the Moore's law. This work is the first proposal of the FPSLA design automation flow, and the approaches to logic synthesis, synchronization, physical mapping, and automatic placement of the FPSLA designs. The synchronization at each gate for pipelining determines the x-coordinates of cells, and reduces the placement to 1-dimensional problems. The objective function and its gradients for the non-linear optimization of the net length and placement density have been remodeled for the reduced global placement problem. Also, a recursive algorithm has been proposed to legalize the placement by relaxing the density overflow of bipartite bin groups in a top-down hierarchical fashion. The proposed model and algorithm are implemented, and validated by applying them to the ACM/SIGDA benchmark designs. The output state of a gate in an FPSLA needs to be duplicated so that each fanout gate can be connected to a dedicated copy. This property has been taken into account by merging the duplicated nets into a hyperedge, and then, splitting the hyperedge into edges as the optimization progresses. This yields additional 18.4% of the cell count reduction in the most dense logic stage. The practicality of the FPSLA can be further enhanced primarily by incorporating into the logic synthesis the constraint to avoid the concentrated fains of gates on some logic stages. In addition, an efficient algorithm needs to be devised for the routing problem which is based on a complicated graph. The graph models the nanowire crossbar which is trimmed to be embedded into the FPSLA fabric, and therefore, asymmetric. These CAD tools can be used to evaluate the fabric efficiency during the architecture enhancement as well as automate the design.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2003.04a
• /
• pp.510-516
• /
• 2003

연안관리 정책을 결정하기 위해서는 다양한 정보의 수집과 이를 체계적으로 관리하고 분석할 수 있는 기법이 필요하다. 특히, 다양한 이해집단과 목적들이 상충하는 지역의 특성을 파악하기 위해서는 환경, 사회, 경제적인 기준 및 의사결정자의 가치체계가 반영될 수 있어야 하며, 선호도가 반영된 요소를 효율적으로 분석할 수 있어야 한다. 이에, 본 연구에서는 공간자료의 처리 및 분석이 용이한 GIS 환경에 다기준 분석법, 그 중에서도 AHP 모형을 결합하는 방법을 다루어 보았다. 분석과정을 살펴보면, 본 연구에서는 지역에 영향을 미치는 사회ㆍ경제적인 지표, 환경 지표를 정하였고, 이런 지표들의 데이터를 GIS라는 도구를 통하여 분석이 용이하도록 변환시켰다. 한편, 이 지역에 영향을 미치는 각 기준들의 중요성을 파악하여 의사결정자의 의견을 반영할 수 있도록 다기준 분석법의 하나인 AHP를 이용하여 가중치를 산정하였다. 다음으로, 다양한 출처의 자료를 표준화하여 GIS의 래스터 자료로 구축한 후, 가중치를 적용한 개별 레이어를 지도대수와 중첩분석을 이용하여 최종 결과 레이어를 생성하였다. 생성된 최종 결과 레이어 상의 공간의 대안인 각 셀 값을 비교ㆍ분석하였다. 이로 인한 결과는 연안의 유한한 자원과 공간의 다양한 이용상태를 관리하기 위한 해안과 육상의 정보를 제공할 수 있다. GIS와 다기준 분석을 통합함으로써 다양한 출처의 공간정보를 분석하고 연안의 현 상태를 밝힐 수 있다. 또한, 이것은 분석 결과가 단순하고 명확하게 설명되어 정책 결정자에게 유용한 정보를 제공할 뿐만 아니라, 이 정보를 이용하여 실질적인 연안관리계획을 수립하는데 도움이 된다.가능성 0.5이상의 면적은 59%를 차지하였다.퇴적이 우세한 것으로 관측되었다.보체계의 구축사업의 시각이 행정정보화, 생활정보화, 산업정보화 등 다양한 분야와 결합하여 보다 큰 시너지 효과와 사용자 중심의 서비스 개선을 창출할 수 있는 기반을 제공할 것을 기대해 본다.. 이상의 결과를 종합해볼 때, ${\beta}$-glucan은 고용량일 때 직접적으로 또는 $IFN-{\gamma}$ 존재시에는 저용량에서도 복강 큰 포식세로를 활성화시킬 뿐 아니라, 탐식효율도 높임으로써 면역기능을 증진 시키는 것으로 나타났고, 그 효과는 crude ${\beta}$-glucan의 추출조건에 따라 달라지는 것을 알 수 있었다.eveloped. Design concepts and control methods of a new crane will be introduced in this paper.and momentum balance was applied to the fluid field of bundle. while the movement of′ individual material was taken into account. The constitutive model relating the surface force and the deformation of bundle was introduced by considering a representative prodedure that stands for the bundle movement. Then a fundamental equations system could be sim

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.1
• /
• pp.74-84
• /
• 2007

This paper presents a new dual-loop Delay Locked Loop(DLL) to expand the delay lock range of a conventional DLL. The proposed dual-loop DLL contains a Coarse_loop and a Fine_loop, and its operation utilizes one of the loops selected by comparing the initial time-difference among the reference clock and 2 internal clocks. The 2 internal clock signals are taken, respectively, at the midpoint and endpoint of a VCDL and thus are $180^{\circ}$ separated in phase. When the proposed DLL is out of the conventional lock range, the Coarse_loop is selected to push the DLL in the conventional lock range and then the Fine_loop is used to complete the locking process. Therefore, the proposed DLL is always stably locked in unless it is harmonically false-locked. Since the VCDL employed in the proposed DLL needs two control voltages to adjust the delay time, it uses TG-based inverters, instead of conventional, multi-stacked, current-starved inverters, to compose the delay line. The new VCDL provides a wider delay range than a conventional VCDL In overall, the proposed DLL demonstrates a more than 2 times wider lock range than a conventional DLL. The proposed DLL circuits have been designed, simulated and proved using 0.18um, 1.8V TSMC CMOS library and its operation frequency range is 100MHz${\sim}$1GHz. Finally, the maximum phase error of the DLL locked in at 1GHz is less than 11.2ps showing a high resolution and the simulated power consumption is 11.5mW.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.53-59
• /
• 2005

In this study, the supercritical electroplating was investigated by forming macroemulsion of electroplating solution using surfactant in supercritical $CO_2$. The fluorinated analogous AOT surfactant, sodium salt of bis (2,2,3,3,4,4,5,5-octafluoro-1-pentanol) sulfosuccinate which has both '$CO_2$ philic' chains and 'hydrophilic' head group was used as a surfactant, and Ni plate and Cu plate were used as the anode and the cathode, respectively. Electroplating was carried out in the conventional method and the supercritical macroemulsion and both results were compared. The supercritical electroplating was carried out in various concentration of surfactant such as 2, 4, 7 wt%, the volume ratio of Ni-plating solution to $CO_2$ was varied in the range of 10-70 vol%, and propane was used as a supercritical fluid instead of $CO_2$. According to the experimental results, the plated surface of Ni on Cu plate performed in supercritical macroemulsion was better than that, in conventional state. In the image of Ni surface plated on Cu plate in supercritical state, there were fewer pin-holes and pits comparing with that in the conventional process. The current and conductivity was increased as the volume ratio of Ni-plating solution to $CO_2$ was increased and the current and the amount of Ni plated on Cu plate were decreased as the concentration of surfactant become higher. In addition, in case of the continuous phase, using $CO_2$ was more effective than using $CO_2$.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.6
• /
• pp.137-143
• /
• 2015

A delay-line type time-to-digital converter (TDC) implemented in a field-programmable gate array (FPGA) is most widely owing due to its simple structure and high conversion rate. However, the delay-line type TDC suffers from nonlinearity error caused by the long delay-line because its time interval measurement range is determined by the length of the used delay line. In this study, a new TDC structure with a shorter delay line by taking a pulse train as an input is proposed for improved time accuracy and efficient use of resources. The proposed TDC utilizes a pulse-train with four transitions and a transition state detector that identifies the used transition among four transitions and prevents the meta-stable state without a synchronizer. With 72 delay cells, the measured resolution and maximum non-linearity were 20.53 ps, and 1.46 LSB, respectively, and the time interval measurement range was 5070 ps which was enhanced by approximately 343 % compared to the conventional delay-line type TDC.

• Culinary science and hospitality research
• /
• v.19 no.5
• /
• pp.100-109
• /
• 2013

This study aims to analyze 19 kinds of mineral contents in hair targeting 311 people in Seoul who suffer from hair loss. The results are as follows: 1. The average contents of all kinds of minerals were within the standards. 2. Sodium, potassium, and selenium were more detected in men than in women; calcium, magnesium, copper, and manganese were more detected in women than in men; toxic elements, mercury, antimony, and arsenic were more detected in men than in women, which was statistically significant. 3. As the age increased, potassium (p<.05), iron (p<.01), manganese (p<.05), chromium (p<.01), and mercury (P<0.01) increased gradually, which was statistically significant. In particular, the content of mercury exceeded its standard in those over fifty. 4. Selenium (p<.01), lead (p<.05), aluminum (p<.05), and arsenic (p<.01) were more detected in natural hair than in permanent or colored hair. Calcium (p<.001), magnesium (p<.001), and manganese (p<.01) were more detected in permanent or colored hair than in natural hair. They were all statistically significant.

• Polymer(Korea)
• /
• v.28 no.4
• /
• pp.314-320
• /
• 2004

Soluble aromatic polyimides bearing 4-(4-oxyalkyleneoxystyryl)- pyridines (ethylene and hexylene) as photoreactive side groups were synthesized and characterized. The photoreactive polymers were soluble in various polar organic solvents and their films were easily formed by solution casting. The photoreactivities of the polymers in the film state were approximately 64% at an exposure energy of 1.5 J/$\textrm{cm}^2$. Transmittances of the polymer films were about 85% after annealing at 20$0^{\circ}C$. Therefore, these polymers can be evaluated to be photoreactive polyimides with good transparency and solubility. The dichroic ratios of the polymers with ethylene and hexylene groups as the alkylene spacers were 0.023 and 0.026, respectively. The order parameters of 4'-pentyl-4-bipheny1carbonitrile as a liquid crystal (LC) in the film cells of the former and latter polymers were 0.50 and 0.52, respectively. These results indicate that the polymers show the effect of alkylene spacer on the photoalignments. The LC in the film cells of the polymers was perpendicularly oriented to the electric vector of the linear polarized UV light (LPUVL).

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.184-192
• /
• 2022

Porous NiO synthesized via hydrothermal synthesis was used in the electrodes of lithium-sulfur batteries to inhibit the elution of lithium polysulfide. The electrode of the lithium-sulfur battery was manufactured as a freestanding flexible electrode using an economical and simple vacuum filtration method without a current collector and a binder. The porous NiO-added S/CNT/NiO electrode exhibited a high initial discharge capacity of 877 mA h g^-1 (0.2 C), which was 125 mA h g^-1 higher than that of S/CNT, and also showed excellent retention of 84% (S/CNT: 66%). This is the result of suppressing the dissolution of lithium polysulfide into the electrolyte by the strong chemical bond between NiO and lithium polysulfide during the charging and discharging process. In addition, for the flexibility test of the S/CNT/NiO electrode, the 1.6 × 4 cm² pouch cell was prepared and exhibited stable cycle characteristics of 620 mA h g^-1 in both the unfolded and folded state.

• Journal of Nutrition and Health
• /
• v.51 no.4
• /
• pp.295-306
• /
• 2018

Purpose: Koreans' internet and smartphone usage hours are steadily increasing and the dependence of young people on smartphones is causing social problems. Therefore, this study was conducted to examine health and dietary habits, as well as hair mineral contents according to the level of dependence of smartphone use among adolescents to clarify the interrelation of smartphone dependence, lifestyle, dietary behavior, and mineral nutrition status. Methods: A total of 80 smartphone-addicted adolescents participated in this study and were divided into three groups (general, potential and danger group) according to smartphone dependence. The subjects' lifestyles and dietary behaviors were then surveyed, and hair mineral contents were analyzed. Results: Higher smartphone dependence was associated with lower average weekly sleeping time and later first smoking age. In the danger group, the rate of eating fast and the rate of snacking twice a day was also relatively high. Parents (45.0%) and mobile (30.0%) were the factors having the greatest influence on an individual's dietary behavior. In the hair mineral analysis, all subjects had lower selenium concentrations and higher lead concentrations than normal. In addition, the levels of aluminum in the danger group were higher than in the normal range and the highest among the three groups. Conclusions: It is necessary to guide adolescents to use smartphones correctly and manage dietary habits. In addition, careful attention is needed the mineral nutritional status of smartphone-addicted adolescents.