• Journal of Sensor Science and Technology
• /
• v.33 no.1
• /
• pp.40-47
• /
• 2024

The creation of vertically aligned one-dimensional (1D) nanostructures through the decoration of n-type tin oxide (SnO₂) on p-type chromium oxide (Cr₂O₃) constitutes an effective strategy for enhancing gas sensing performance. These heterostructures are deposited in multiple stages using a glancing angle deposition technique with an electron beam evaporator, resulting in a reduction in the surface porosity of the nanorods as SnO₂ is incorporated. In comparison to Cr₂O₃ films, the bare Cr₂O₃ nanorods exhibits a response 3.3 times greater to 50 ppm H₂S at 300℃, while the SnO₂-decorated Cr₂O₃ nanorods demonstrate an eleven-fold increase in response. Furthermore, when subjected to various gases (CH₄, H₂S, CO₂, H₂), a notable selectivity toward H₂S is observed. This study paves the way for the development of p-type semiconductor sensors with heightened selectivity and sensitivity towards H₂S, thus advancing the prospects of gas sensor technology.

• Journal of the Korean Magnetics Society
• /
• v.2 no.3
• /
• pp.277-281
• /
• 1992

We have designed, fabricated and tested an integrated planar DC SQUID which incorporates input coil and mofulation coil in thin film structure. The SQUID uses Nb /Al-oxide /Nb Josephson junctions and Pd shunt resistors, and the SQUID loop incorporates two rings connected in series forming figure '8' structure and has the advantage of a negligibly small circulating current for the spatially homogeneous noise fields. The devices were fabricated using photolithographic technique, RF magnetron sputtering, anodic oxidation for insulation and lift-off process. The preliminary test of the fabricated SQUID at 4.2 K showed that the flux-voltage characteristics were smooth enough to adopt standard readout system, and the voltage noise was too small to be measured by direct method and so the white noise was thought to be less than $10^{-4}\;{\phi}_o/\;\sqrt{H_z}$.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1254-1260
• /
• 2009

CDMA tele-Controller system is designed with a low power consumption 8 bit microcontroller, ATmega 2560. ATmega 2560 microcontroller consists of 4 UART (Universal asynchronous receiver/transmitter) ports, 4 kbytes EEPROM, 256 kbytes flash memory, 4 kbytes SRAM. 4 URAT is used for CDMA modem, communication for GPS module, EEPROM is used for saving a configuration for program running, a flash memory of 256 kbytes is used for storing a F/W(Firm Ware), and SRAM is used for stack, storing memory of global variables while program running. We have tested the communication distance between the coast station and sea by the fabricated control board using 800 MHz CDMA modem and GPS module, which is building for the navigational aid management system by remote control. As a results, the receiving signal strength is above -80 dBm, and then the characteristics of the control board implemented more than 10 km in the distance of the communication.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.8
• /
• pp.789-798
• /
• 2013

The procedures and relevant programs developed for analyzing mechanical load data of wind turbine generator systems, which are obtained through type certification tests, are verified. The following issues according to IEC 61400-13 are covered in the developed programs: data validation, time series analysis, summary load statistics, generation of fatigue load spectra, and estimation of equivalent loads. A capture matrix for normal power production is generated to determine whether the collected data sets are sufficient to carry out fatigue analysis. Fatigue load spectra are obtained through the rainflow counting method using 50 load ranges; finally, equivalent loads are calculated using different S-N curve slopes, m, according to the relevant materials. Case studies are performed using aero-elastic simulation data of the NREL 5 MW baseline wind turbine with a monopile foundation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.4
• /
• pp.495-501
• /
• 2014

Piezoresistive-type, capacitive-type, and optical-type sensors have mainly been used for measuring a strain. However, in building a sensor network for remote monitoring using these conventional sensors there are disadvantages such as the complexity of a measuring system including wireless communication circuitry and high cost. In this paper, we demonstrates a highly-sensitive surface acoustic wave (SAW) strain sensor which is advantageous to harsh environments and wireless network. We designed and fabricated the SAW strain sensor. The SAW strain sensor attached on a specimen was tested with a tensile tester. The strain on the sensor surface was measured with a commercial strain gauge and compared with that obtained from strain analysis. The central frequency shift of the SAW sensor was measured with a network analyzer. The sensitivity of the SAW strain sensor is 134 $Hz/{\mu}{\varepsilon}$ which is high compared to previous results.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.1
• /
• pp.185-190
• /
• 2020

The rapid aging is increasing as the shortage of medical facilities and the resulting of decline in the quality of public health. In order to ease the burden of rising medical expenses, advanced medical institutions are expanding their remote medical care to lower the cost of services. U-healthcare detects the changes in physical and chemical phenomena occurring in the human body and converts them into electrical signals that can be processed and feeds back to the results through analytical and visualization processes to select only the desired information from the measured signals. The service is provided through a process of providing an alarm to a user. However, traditional biometric methods of attaching sensors directly to the body can be annoying and rejected in daily life. Therefore, there is a need for a method of continuously measuring biometric information without causing inconvenience to daily life. In this paper, we propose an IR-UWB-based non-contact and non-responsive respiratory measurement system that can continuously monitor biological information without any inconveniences to daily life.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.6
• /
• pp.599-606
• /
• 2015

International Hydrographic Organization(IHO) adopted standard S-100 as the international standard Geographic Information System(GIS) that can be generally used in the maritime sector. Accordingly, the next-generation system to support navigation information based on GIS standard technology has being developed. AR based navigation information system that supported navigation by overlapping navigation information on the CCTV image has currently being developed. In this study, we considered the application of a transparent display as a method to support efficiently this system. When a transparent display applied, the image distortion caused by using a wide-angle lens for parallax secure, and the disc s, and demonstrated the applicability of the technology by developing a prototype.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.2
• /
• pp.97-104
• /
• 2011

This paper deals with the quick and precise disaster prevention automation system (DPAS) based on information communication technology (IT) that detects fire and disasters in the building automatically and quickly and then activates the facilities to extinguish fire and disasters, monitoring such situation in a real time through wire-wireless communication network. The proposed DPAS is applied a programmable logic controller (PLC) of one-chip type which is smallsize and lightweight and also has highly sensitive-precise reliabilities. The one-chip type PLC analyzes detected signals from sensors in a case of fire and disasters, then activates fire extinguishing facilities for rapid suppression. The detected data is also transferred to a remote situation room through wire-wireless network of RS232c and bluetooth communication. The transferred data sounds an emergency alarm signal, and operates a monitoring program. The proposed DPAS based on IT will minimize the life and wealth loss from rapid measures while prevents fire and disasters.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.626-626
• /
• 2013

P-N 접합에 의해 절연된 게이트를 통해 전류 통로를 제어하는 접합형 전계효과 트랜지스터(Junction Field Effect Transistors; JFETs)는, 입력 임피던스가 크고, 온도에 덜 민감하며, 제조가 간편하여 집적회로(IC) 제조가 용이하고, 동작의 해석이 단순하다는 장점을 가지고 있다. 특히 JFET는 선형적인 전류의 증폭 특성을 가지고 있으며, 잡음이작기 때문에, 감도가 우수한 음향 센서의 증폭회로, 선형성이 우수한 증폭회로, 입력 계측 증폭 회로 등에 주로 사용되고 있다. 기존에 사용되는 JFET 소자는 구조와 제조 공정에 따라서, 컷 오프 전압($V_{cut-off}$)과 드레인-소스 포화 전류($I_{DSS}$)의 변화가 심하게 발생하여, 소자의 전기적 특성 제어가 어렵고, 소자의 수율이 낮다는 문제점이 있다. 본 연구에서는 TCAD 시뮬레이션을 통해 게이트 전압에 의해 채널이 형성되는 채널 층의 상하부에 각각 $Si_xGe_{1-x}$로 이루어진 상부 및 하부 확산 저지층을 삽입한 JFET 소자 형성하여, 게이트 접합부의 접합 영역 확산을 저지하고, 상기 게이트 접합부가 계면에서 날카로운 농도 구배를 갖도록 함으로써, 공정 변화에 따른 전기적 특성의 편차가 작아지는 JFET 소자 구조를 만들어 전기적 특성을 개선하였다. JFET은 채널층에 삽입된 $Si_xGe_{1-x}$ 층의 두께, Ge 함유량 및 n채널층의 두께를 변화하였을 때, off 상태의 게이트-소스 전압이 감소한 반면에 드레인-소스 포화 전류($I_{DSS}$)와 컨덕턴스(gm) 값이 증가하였다. 삽입된 $Si_xGe_{1-x}$층이 Boron이 밖으로 확산되는 현상이 감소하여 채널이 좁아지는 현상을 막아 소자의 전기적 특성을 개선함으로써 제조공정의 변화에 관계없이 컷오프 전압을 정확하고 안정되게 제어할 수 있고 이를 통해 소자의 수율을 높일 수 있을 것으로 기대된다.

• Journal of Broadcast Engineering
• /
• v.10 no.1 s.26
• /
• pp.22-30
• /
• 2005

We implement an interactive 3D audio broadcasting terminal which synthesizes an audio scene according to the request of a user. Audio scene structure is described by the MPEG-4 AudioBIFS specifications. The user updates scene attributes and the terminal synthesizes the corresponding sound images in the 3D space. The terminal supports the MPEG-4 Audio top nodes and some visual nodes. Instead of using sensor nodes and route elements, we predefine node type-specific user interfaces to support BIFS commands for field replacement. We employ sound spatialization, directivity/shape modeling, and reverberation effects for 3D audio rendering and realistic feedback to user inputs. We also introduce a virtual concert program as an application scenario of the interactive broadcasting terminal.