• Journal of the Korean Society of Safety
• /
• v.27 no.4
• /
• pp.13-19
• /
• 2012

The purpose of this study is to extract the major factors related to the deterioration mechanism of white organic light-emitting diodes(WOLED) by performing accelerated testing of temperature, voltage, time, etc., and to develop an accelerated life test(ALT) model. The measurement results of the brightness of the WOLED exhibited that their average brightness tended to increase as the operating voltage increased and that the half-life period of the brightness appeared after approximately 400 hours when the operating voltage was 20V and the ambient temperature was $85^{\circ}C$. It could be seen that although the WOLED showed comparatively the same brightness when the initial acceleration began after the operating voltage was applied to it, its brightness changed excessively after the WOLED's thermal storage had been made. In addition, it was observed that the half-life period was reduced as the ambient temperature and applied voltage increased. The strength of the WOLED which had been maintained in the range of visible light at the maximum load was reduced by the deterioration of the organic light emitting material due to the influence of the operating voltage and temperature, and the reduction of emitted light was small at low voltage and temperature. It could be seen that the failure of the WOLED during the ALT was caused by wear due to load accumulation over time, and that Weibull distribution was appropriate for the life distribution and acceleration was established between test conditions. From the WOLED analysis, it is thought that factors influencing the brightness deterioration are voltage, temperature, etc., and that comprehensive analysis considering discharge control, dielectric tangent margin, etc., would further increase the reliability.

• The Journal of the Korea Contents Association
• /
• v.7 no.1
• /
• pp.139-146
• /
• 2007

Most of embedded systems have been developed practically based on the PC platform equipped with Intel x86 CPU since it is able to reduce the total time for product development and improve the reliability of product by making use of a variety of solutions developed for a long time in the PC environment. Also, embedded systems based on PC-platform mainly use a high-capacity hard disk as data storage device for applications intending to store multimedia data. Recently, while the capacity of hard disk is increasing rapidly, the start-up ready time of hard disk is growing longer more than 30 seconds. The lengthened start-up ready time may delay the booting time of embedded system seriously, weighting users down with inconvenience. This paper proposes the refined system architecture and the dynamic IDE device probing method for fast booting of linux kernel in the embedded system based on PC platform with high-capacity hard disks, and the performance of proposed methods is evaluated and presented.

• Journal of KIISE:Information Networking
• /
• v.35 no.2
• /
• pp.120-129
• /
• 2008

The purpose of sensor network is gathering the information from sensor nodes. If there are selfish node that deliberately avoid packet forwarding to save their own energy, the sensor network has trouble to collect information smoothly. To solve this problem we suggest a mechanism which uses credit payment schema according to the amount of forwarding packets. Sensor nodes use credits to send their own message and they forward packets of other sensor nodes to get credits. To offer authenticity we combined the roles of sink node and server, also we used piggybacking not to send additional report message. The packet trace route is almost fixed because sensor node doesn't have mobility. In this case, it happens that some sensor nodes which don't receive forwarding packets therefore they can't get credit. So, we suggested the way to give more credits to these sensor nodes. Finally, we simulated the suggested mechanism to evaluate performance with ns2(network simulator). As a result, packet transmission rate was kept on a high rate and the number of arrival packets to sink node was increased. Also, we could verify that more sensor nodes live longer due to deceasing the energy consumption of sensor nodes.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.6
• /
• pp.643-648
• /
• 2013

In this paper, we developed a system which can detect and can alarm about the sailing provocative climate by using a photo. The research on domestic shipbuilding industry and in IT fusion technology is under construction, but a reliable safety device which can alarm a sailor about the circumstances of the fog and rain during ship operation as soon as possible due to the constant state in domestic. In this paper, a compact, for system low-power transceiver and data processing equipment for sensing were developed, also a performance evaluation got accomplished with simulation analysis. In results, it is operating normally at least 32.36[dB] and maximum values f 89.20[dB] in the domestic, and 32.55 to 60.66[dB] in the outdoors.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.3A
• /
• pp.230-236
• /
• 2007

This paper presents a resource management mechanism for the mesh networking in IEEE 802.15.3 High-rate WPAN. IEEE 802.15 TGS is standardizing the MAC and PHY for mese networking. This task group researches the mechanism that are extension of network coverage without increasing transmit power of receive sensitivity, and studies the enhanced reliability via route redundancy. In this paper we propose the distributed resource management scheme that is fairly using the channel resource in the piconet without centralized piconet coordinator. Each DEV reserves the channel time and broadcasts its information. This scheme has unfairness for later associated DEV because of preoccupation of earlier associated DEVs. This paper presents the method that fairly allocates the channel time in MAC layer. And we evaluate the performance enhancement using simple simulations.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.43 no.5 s.311
• /
• pp.1-11
• /
• 2006

This paper presents a digital auto-focusing method using a priori estimated point-spread-functions (PSF) database. The proposed algorithm efficiently removes out-of-focus blur in a degraded input image by selecting the optimal PSF from the database. The database consists of optical characteristics of image formation system. The PSF selection Process is performed based on a novel focusing measure. The proposed method includes a spatially adaptive filter for removing both noise and ringing artifacts. Experimental results show that the proposed method efficiently removes out-of-focus blur using significantly reduced computational load compared with the existing method.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.2
• /
• pp.17-23
• /
• 2000

Wireless link has high bit error rate compared with wired link and many users share this limited bandwidth. So it needs more powerful error control code and efficient media access control(MAC) to provide multimedia service reliably. In this paper we proposed efficient MAC frame format based on TDMA using mini-slot for request access. The number of mini-slots is variable based on the result of collision in the previous frame. This dynamic allocation of request mini-slots helps resolve the contention situation quickly and avoids the waste of bandwidth that may occur when there are several unneeded request mini-slots. The simulation results are also presented in terms of channel utilization, call blocking probability and cell transmission delay for mixed traffic environment.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.200-203
• /
• 2009

Ultrasonic techniques have the advantage of determining the burning rates with wide range of pressure in only a single test. However, ultrasonic techniques have a drawback, which is that they are using high frequency transducers and it is easily affected by noise. Therefore, ultrasonic measurement method needs noise reduction algorithm to improve or grantee accuracy of burning rate measurements of solid propellants using ultrasound. Thus, in the present study, we propose a noise reduction method of measured ultrasonic signals by applying wavelet shrinkage.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.3
• /
• pp.246-253
• /
• 2002

This paper describes the development and the field application of the ultrasonic gas flowmeter for accurate measurement of the volumetric flow rate of gases in a harsh environmental conditions in iron & steel making company. This ultrasonic flowmeter is especially suited for measuring LDG, COG, BFG gases produced in iron & steel making process. This is a transit time type ultrasonic flowmeter. We have developed the transmitting & receiving algorithm of ultrasonic wave and the ultrasonic signal processing algorithm to develope a transit time type ultrasonic flowmeter. We have evaluated the performance of ultrasonic flowmeter by the calibration system with Venturi type standard flowmeter. We has confirmed its reliability by extensive field tests for a year in POSCO, iron & steel making company. Now we have developed the commercial model of ultrasonic flowmeter and applied to the POSCO gas line.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.7
• /
• pp.587-592
• /
• 2016

Bellows for LNG carriers must be corrosion resistant in order to operate in seawater environments. They must also have long fatigue lives in order to withstand the expansion and contraction caused by large temperature changes and continuous vibration in extreme environments. In order to incorporate these properties into bellow design, it is important to use materials that are resistant to cold brittleness and corrosion, and maintain their optimized forming condition. The design conditions and forming methods used for bellows must be optimized in order to incorporate these characteristics. In this study, finite element analysis was used to develop cryogenic bellows, which have good mechanical strength and reliability. In addition, two different forming methods (mechanical and hydroforming) were used to design and produce bellows, in order to derive their forming condition. The height, thickness, and hardness of the convolutions of bellows produced by each method were measured and compared with each other. The results confirmed that the two forming methods produced bellows with different mechanical properties.