• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.5
• /
• pp.519-526
• /
• 2018

In this study, an algorithm to predict evacuation routes in support of shipboard lifesaving activities is presented. As the first step of algorithm development, the feasibility and necessity of an evacuation route prediction algorithm are shown numerically. The proposed algorithm can be explained in brief as follows. This system continuously obtains and analyzes passenger movement data from the ship's monitoring system during non-disaster conditions. In case of a disaster, evacuation route prediction information is derived using the previously acquired data and a prediction tool, with the results provided to rescuers to minimize casualties. In this study, evacuation-related data obtained through fire evacuation trials was filtered and analyzed using a statistical method. In a simulation using the conventional evacuation prediction tool, it was found that reliable prediction results were obtained only in the SN1 trial because of the conceptual and structural nature of the tool itself. In order to verify the validity of the algorithm proposed in this study, an industrial engineering tool was adapted for evacuation characteristics prediction. When the proposed algorithm was implemented, the predicted values for average evacuation time and route were very similar to the measured values with error ranges of 0.6-6.9 % and 0.6-3.6 %, respectively. In the future, development of a high-performance evacuation route prediction algorithm is planned based on shipboard data monitoring and analysis.

• Membrane Journal
• /
• v.30 no.1
• /
• pp.57-65
• /
• 2020

The purpose of this study was to compare the water channel morphology and the proton conductivity by changing the number of repeating units of the polymer backbone of PEMs, and to present a criterion for selecting an appropriate polymer model for MD simulation. In the model with the shortest polymer main chain, the movement of the main chain and the sulfonic acid group was observed to be large, but no change in the water channel morphology was found. In addition, due to the nature of the proton transport ability that is most affected by the water channel morphology, the proton conductivity did not show a significant correlation with the length of the polymer backbone. These results provide important information, particularly for the preparation of ionomers for binders. In general, a low molecular weight polymer electrolyte material is used for a binder ionomer. Since the movement of the main chain/sulfonic acid group is improved, it can play a role of enclosing the catalyst layer well. However, there is no change in its proton conducting performance. In conclusion, the preparation of ionomers for binders will require molecular weight and structure design with a focus on physical properties rather than proton transfer performance.

• Journal of Biomedical Engineering Research
• /
• v.18 no.4
• /
• pp.429-438
• /
• 1997

Mechanical valve is one of the most widely used implantable artificial organs of which the reliability is so important that its failure means the death of patient. Therefore early noninvasive detection is essentially required, though mechanical valve failure with thrombosis is the most common. The objective of this paper is to detect the thrombosis formation by spectral analysis and neural network. Using microphone and amplifier, we measured the sound from the mechanical valve which is attached to the pneumatic ventricular assist device. The sound was sampled by A/D converter(DaqBook 100) and the periodogram is the main algorithm for obtaining spectrum. We made the thrombosis models using pellethane and silicon and they are thrombosis model on the valvular disk, around the sewing ring and fibrous tissue growth across the orifice of valve. The performance of the measurment system was tested firstly using 1 KHz sinusoidal wave. The measurement system detected well 1KHz spectrum as expected. The spectrum of normal and 5 kinds of thrombotic valve were obtained and primary and secondary peak appeared in each spectrum waveform. We find that the secondary peak changes according to the thrombosis model. So to distinguish the secondary peak of normal and thrombotic valve quantatively, 3 layer back propagation neural network, which contains 7, 000 input node, 20 hidden layer and 1 output was employed The trained neural network can distinguish normal and valve with more than 90% probability. As a conclusion, the noninvasive monitoring of implanted mechanical valve is possible by analysing the acoustical spectrum using neural network algorithm and this method will be applied to the performance evaluation of other implantable artificial organs.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.49 no.2
• /
• pp.28-34
• /
• 2012

Various feature extraction algorithms are widely applied to real-time image processing applications for extracting significant features from images. Feature extraction algorithms are mostly combined with image processing algorithms mostly for image tracking and recognition. Feature extraction function is used to supply feature information to the other image processing algorithms and it is mainly implemented in a preprocessing stage. Nowadays, image processing applications are faced with embedded system implementation for a real-time processing. In order to satisfy this requirement, it is necessary to reduce execution time so as to improve the performance. Reducing the time for executing a feature extraction function dose not only extend the execution time for the other image processing algorithms, but it also helps satisfy a real-time requirement. This paper explains FAST (Feature from Accelerated Segment Test algorithm) of E. Rosten and presents FPGA-based embedded hardware accelerator architecture. The proposed acceleration scheme can be implemented by using approximately 2,217 Flip Flops, 5,034 LUTs, 2,833 Slices, and 18 Block RAMs in the Xilinx Vertex IV FPGA. In the Modelsim - based simulation result, the proposed hardware accelerator takes 3.06 ms to extract 954 features from a image with $640{\times}480$ pixels and this result shows the cost effectiveness of the propose scheme.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.12
• /
• pp.3-11
• /
• 2014

Multiple antennas can provide huge capacity gains when the transmitter knows the channel state information (CSI). Precoding is a technique that exploits CSI at the transmitter side. In this paper, an adaptive precoding scheme is proposed, called a hybrid multiple-input multiple-output (MIMO) precoding (HMP). HMP is a combination of linear and nonlinear precoding. The number of transmit antennas less than or equal to four is as same as the conventional antenna selection scheme. Therefore, the HMP scheme uses more than four transmit antennas. The good channel means that the channels must be selected to maximize the channel capacity among the given channels, and the rest channels are called bad channel. In HMP scheme, we use the nonlinear precoding in the good channels and the linear precoding in the bad channels. The well-known Tomlinson-Harashima precoding (THP) is considered as nonlinear precoding. The system throughput and MSE (minimum square error) are shown for the performance of HMP scheme compared to the conventional schemes which are BD (block diagonalization), antenna selection and THP.

• Journal of the Korea Concrete Institute
• /
• v.17 no.6 s.90
• /
• pp.975-982
• /
• 2005

Scientific community agrees about the fact that base Isolation provides interesting solutions to minimize the seismic risk. Reliability of such a technique is nowadays proofed by a large number of applications like public buildings, nuclear plants, bridges, etc. This paper reports the results of performance verification tests of the base isolated RC building with the laminated rubber bearings which is manufactured by enterprise in Korea. The shaking table tests were performed using a three story model scaled to 1/3 of the prototype RC apartment building. Several major earthquake records were scaled to different peak ground accelerations and used as input base excitations. Especially in this study, effect of earthquake characteristics on response reduction and effect of the intensity of excitations are studied. Through the verification tests, the validity of the applied base isolaion device and the response reduction effect against earthquakes are confirmed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.10
• /
• pp.1976-1985
• /
• 2015

The amount of packets in palyout buffer of video streaming receiver can be changed by network condition, and saturated and exhausted by the delay and jitter. Especially, if the amount of incoming video traffic exceeds the maximum allowed playout buffer, buffer overflow problem can be generated. It makes the deterioration of video image and the discontinuity of playout by skip phenomenon. Also, if the incoming packets are delayed by network confusion, the stop phenomenon of video image is made by buffering due to buffer underflow problem. To solve these problems, this paper proposes the video streaming receiver with token bucket scheme which automatically establishes the important parameters like token generation rate r and bucket maximum capacity c adapting to the pattern of video packets. The simulation results using network simulator-2 (NS-2) and joint scalable video model (JSVM) show that the proposed token bucket scheme with automatic establishment parameter provides better performance than the existing token bucket scheme with manual establishment parameter in terms of the generation number of overflow and underflow, packer loss rate, and peak signal to noise ratio (PSNR) in three test video sequences.

• Spatial Information Research
• /
• v.23 no.2
• /
• pp.1-9
• /
• 2015

Graphical processing unit (GPU) contains many arithmetic logic units (ALUs). Because many ALUs can be exploited to process parallel processing, GPU provides efficient data processing. The spatial data require many geographic coordinates to represent the shape of them in a map. The coordinates are usually stored as geodetic longitude and latitude. To display a map in 2-dimensional Cartesian coordinate system, the geodetic longitude and latitude should be converted to the Universal Transverse Mercator (UTM) coordinate system. The conversion to the other coordinate system and the rendering process to represent the converted coordinates to screen use complex floating-point computations. In this paper, we propose a parallel processing technique that processes the conversion and the rendering using the GPU to improve the performance. Large spatial data is stored in the disk on files. To process the large amount of spatial data efficiently, we propose a technique that merges the spatial data files to a large file and access the file with the method of memory mapped file. We implement the proposed technique and perform the experiment with the 747,302,971 points of the TIGER/Line spatial data. The result of the experiment is that the conversion time for the coordinate systems with the GPU is 30.16 times faster than the CPU only method and the rendering time is 80.40 times faster than the CPU.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.3
• /
• pp.588-594
• /
• 2015

Although GPS technology for location positioning system has been widely used, it is difficult to be used in intelligent transport systems, due to the large positioning error and limited area for receiving radio signals. Thanks to the rapid development of LED technology, LED lights become popular in many applications. Especially, visible light communications (VLC) has raised a lot of interests because of the simultaneous functioning of LED illumination and communication. Recent studies on positioning system using VLC mainly focused on indoor environments and still difficult to satisfy positioning accuracy and simple implementation simultaneously. In this paper, we propose a positioning system based on VLC using the coordinate information of LEDs installed on the road infrastructure. Extracting the LED signal, obtained through VLC, from the easily accessible camera image, it is possible to estimate the position of the car on the road. Simulation results show that the proposed scheme can achieve a high positioning accuracy of 1 m when large number of pixels is utilized and the distance from the LED light is close.

• Journal of Biomedical Engineering Research
• /
• v.24 no.4
• /
• pp.363-367
• /
• 2003

Contact area and pressure are important factors which directly influence a life of knee implants. Since implant's mechanical functions should be experimentally evaluated for clinical use, many studies using a knee simulator and a pressure sensor system have been conducted. However it has not been reported that the contact pressure's distribution of a knee implant motion was estimated in real-time during a gate cycle. Therefore. the objective of this study was to analyze the contact pressure distribution for the motion of a joint using the knee simulator and I-scan sensor system. For this purpose, we developed a force-controlled dynamic knee simulator to evaluate the mechanical performance of artificial knee joint. This simulator includes a function of a soft tissue and has a 4-degree-of-freedom to represent an axial compressive load and a flexion angle. As axial compressive force and a flexion angle of the femoral component can be controlled by PC program. The pressure is also measured from I-scan system and simulator to visualize the pressure distribution on the joint contact surfaces under loading condition during walking cycle. The compressive loading curve was the major cause for the contact pressure distribution and its center move in a cycle as to a flexion angie. In conclusion, this system can be used to evaluate to the geometric interaction of femoral and tibial design due to a measured mechanical function such as a contact pressure, contact area and a motion of a loading center.