• 보일러설비
• /
• s.77
• /
• pp.87-93
• /
• 2000

• Bulletin of Food Technology
• /
• v.9 no.1
• /
• pp.87-107
• /
• 1996

• Journal of Korea Foundry Society
• /
• v.42 no.3
• /
• pp.177-182
• /
• 2022

• Journal of Korea Foundry Society
• /
• v.42 no.2
• /
• pp.112-122
• /
• 2022

• Journal of Korea Foundry Society
• /
• v.43 no.2
• /
• pp.77-83
• /
• 2023

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.350-350
• /
• 2021

한국건설기술연구원의 돌발홍수연구센터는 돌발홍수예측 시스템을 구축하여 2019년부터 전국에서의 돌발홍수정보를 제공하고 있다. 2019년에는 초단기 예측 모델인 Macgill Algorithm for Precipitation-nowcast by Lagrangian Extrapolation(MAPLE) 알고리즘으로부터 생산된 초단기 예측 강우를 활용하여 동(읍/면) 단위로 1시간 선행 예보를 제공하였다. 2020년에는 추가로 초단기 예측 강우와 수치예보 자료를 병합한 예측 병합 강우 자료를 생산하여 예측 선행시간을 1시간에서 3시간까지 확장하였다. 돌발홍수예측 시스템의 목표는 도시 및 산지소하천에서의 돌발홍수에 대응하기 위한 정보를 실시간으로 사용자에게 제공하여 수재해에 빠르게 대응하는 것이다. 이에 돌발홍수예측 시스템은 2019년부터 실시간으로 운영하여 홍수기에 보다 빠른 돌발홍수정보를 제공해왔다. 본 연구에서는 2020년 우기에 운영된 돌발홍수시스템에 대한 평가를 수행하였다. 이를 위해 부산(07.23), 대전(07.29), 서울(08.01), 경기-충북(08.02)에서 발생한 수재해 사례를 분석하였다.

• Korean Journal of Metals and Materials
• /
• v.56 no.11
• /
• pp.805-812
• /
• 2018

High pressure die casting is one of the precision casting methods. It is highly productivity and suitable for manufacturing components with complex shapes and accurate dimensions. Recently, there has been increasing demand for efficient heat dissipation components, to control the heat generated by devices, which directly affects the efficiency and life of the product. Die cast aluminum alloys with high thermal conductivity are especially needed for this application. In this study, the influence of elements added to the die cast aluminum alloy on its thermal conductivity was evaluated. The results showed that Mn remarkably deteriorated the thermal conductivity of the aluminum alloy. When Cu content was increased, the tensile strength of cast aluminum alloy increased, showing 1 wt% of Cu ensured the minimum mechanical properties of the cast aluminum. As Si content increased, the flow length of the alloy proportionally increased. The flow length of aluminum alloy containing 2 wt% Si was about 85% of that of the ALDC12 alloy. A heat dissipation component was successfully fabricated using an optimized composition of Al-1 wt%Cu-0.6 wt%Fe-2 wt%Si die casting alloy without surface cracks, which were turned out as intergranular cracking originated from the solidification contraction of the alloy with Si composition lower than 2 wt%.

• Korean Journal of Metals and Materials
• /
• v.49 no.11
• /
• pp.845-852
• /
• 2011

The Spark Plasma Sintering(SPS) method offers a means of fabricating a sintered-body having high density without grain growth through short sintering time and a one-step process. A titanium compact having high density and purity was fabricated by the SPS process. It can be used to fabricate a Ti sputtering target with controlled parameters such as sintering temperature, heating rate, and pressure to establish the optimized processing conditions. The compact/target(?) has a diameter of ${\Phi}150{\times}6.35mm$. The density, purity, phase transformation, and microstructure of the Ti compact were analyzed by Archimedes, ICP, XRD and FE-SEM. A Ti thin-film fabricated on a $Si/SiO_2$ substrate by a sputtering device (SRN-100) was analyzed by XRD, TEM, and SIMS. Density and grain size were up to 99% and below $40{\mu}m$, respectively. The specific resistivity of the optimized Ti target was $8.63{\times}10^{-6}{\Omega}{\cdot}cm$.

• Journal of Sensor Science and Technology
• /
• v.30 no.5
• /
• pp.331-336
• /
• 2021

The Non-dispersive Infrared (NDIR) gas sensor has high selectivity, measurement reliability, and long lifespan. Thus, even though the NDIR gas sensor is expensive, it is still widely used for carbon dioxide (CO₂) detection. In this study, to reduce the cost of the NDIR CO₂ gas sensor, we proposed the new optical waveguide structure design based on ready-made gas pipes that can improve the sensitivity by increasing the initial light intensity. The new optical waveguide design is a structure in which a part of the optical waveguide filter is inclined to increase the transmittance of the filter, and a parabolic mirror is installed at the rear end of the filter to focus the infrared rays passing through the filter to the detector. In order to examine the output characteristics of the new optical waveguide structure design, optical simulation was performed for two types of IR-source. As a result, the new optical waveguide structure can improve the sensitivity of the NDIR CO₂ gas sensor by making the infrared rays perpendicular to the filter, increasing the filter transmittance.

• Journal of Powder Materials
• /
• v.26 no.2
• /
• pp.132-137
• /
• 2019

Tungsten carbide (WC) hard materials are used in various industries and possess a superior hardness compared to other hard materials. They have particularly high melting points, high strength, and abrasion resistance. Accordingly, tungsten carbide hard materials are used for wear-resistant tools, cutting tools, machining tools, and other tooling materials. In this study, the WC-5wt.%Co, Fe, Ni hard materials are densified using the horizontal ball milled WC-Co, WC-Fe, and WC-Ni powders by a spark plasma sintering process. The WC-5Co, WC-5Fe, and WC-5Ni hard materials are almost completely densified with a relative density of up to 99.6% after simultaneous application of a pressure of 60 MPa and an electric current for about 15 min without any significant change in the grain size. The average grain size of WC-5Co, WC-5Fe, and WC-5Ni that was produced through SPS was about 0.421, 0.779, and $0.429{\mu}m$, respectively. The hardness and fracture toughness of the dense WC-5Co, WC-5Fe, WC-5Ni hard materials were also investigated.